Effect of oxide-based fluxes on mechanical and metallurgical properties of Dissimilar Activating Flux Assisted-Tungsten Inert Gas Welds

Present investigation is to study the “Effect of Activating Fluxes on Mechanical and Metallurgical Properties of Dissimilar Activated Flux-Tungsten Inert Gas Welds”. Effect of current, welding speed, joint gap and electrode diameter on weld bead dimensions on 6 mm thick dissimilar weld between carbon steel to stainless steel, was studied under Activated Flux-Tungsten Inert Gas Welding process. During this investigation three different types of oxide powders were used-TiO₂, ZnO and MnO₂. After welding samples were subject to mechanical testing, in addition to characterization via micro hardness and microstructures of Normal Tungsten Inert Gas Welds and Activated Flux-Tungsten Inert Gas Welds. Activating fluxes TiO₂ and ZnO are effective fluxes for Activated Flux-Tungsten Inert Gas Welding of dissimilar weld between CS to SS. Highest depth/width (D/W) ratio reported under TiO₂ and ZnO fluxes compare to Normal-Tungsten Inert Gas Welds. Lowest angular distortion was observed under TiO₂ flux compare to Normal-Tungsten Inert Gas Welds. Mechanical properties, Joint Efficiency of Activated Flux-Tungsten Inert Gas Welds are higher than normal-Normal Tungsten Inert Gas Welds. Tensile Test specimens of both the processes failed from the parent metal (carbon steel side). Carbon migration from CS to SS, had occurred which led to failure of weld joints from CS side.     

Microstructure of 2205 duplex stainless steel joint in submerged arc welding by post weld heat treatment

The 2205 duplex stainless steel (DSS) is of both good properties austenitic steel and ferritic steel, which applies to the shipbuilding industry usually. In this paper, the OM, XRD and microhardness test methods are used to analyze the variation of submerged arc welded (SAW) joints with and without post weld heat treatment (PWHT). The research results show that the σ phase disappear in the fusion edge zone near heat affect zone (HAZ) and an increase in the welded center zone during the follow-up PWHT, while the amount of γ phase is decreased in the welded center zone with PWHT. A segregation distribution of some second phases is also found in the welded center zone after PWHT. There have two pick values of microhardness arise in the fusion edge zone and the welded center zone separately without PWHT. However, a maximum value of microhardness at the fusion edge zone near HAZ is disappeared and the other is still held at the welded center zone during PWHT. It can be attributed to the changes of second phases, element diffusions and particle segregation during PWHT. A developing mechanism is issued to demonstrate the second phases transferring of the 2205 DSS SAW joints by PWHT.     

45~#钢在西双版纳大气环境下的腐蚀研究

目的研究西双版纳热带雨林地区大气环境下材料的初期腐蚀行为。方法使用45#碳钢在西双版纳大气环境下进行1年的大气暴露腐蚀试验,并利用质量损失分析、SEM、XRD和FTIR等技术,分析45#碳钢在西双版纳大气环境下暴露1年的腐蚀行为。结果 45#碳钢的腐蚀产物以γ-FeOOH,Fe(OH)3和Fe3O4为主,并有少量的α-FeOOH。结论西双版纳大气环境腐蚀性为C2级。在暴露1年的时间内,锈层化学稳定性随试验时间的延长逐渐增强,对基体的保护性逐渐加大。     

某大型钢结构项目喷涂废气污染防治措施可行性分析研究

钢结构建筑是一种新型的节能环保的建筑体系,大多数大型钢结构产品在生产过程中均需要进行抛丸除锈、喷涂处理,使用油漆进行喷涂过程中将不可避免地产生含TVOC(主要为甲苯、二甲苯和非甲烷总烃)的有机废气。大型钢构类生产项目喷涂废气的收集和处理尤为困难。文章结合某大型钢结构生产企业实际采取的喷涂废气治理方法进行喷涂废气污染防治可行性分析,旨在为同类项目喷涂废气污染治理及进一步改良涂装废气治理工艺和技术提供参考依据。     

模拟烹饪油烟的粒径分布与扩散

烹饪油烟颗粒物粒径分布与扩散特性研究有助于解析其对室内空气质量和居民健康的影响,采用电子低压撞击器(ELPI)实时监测了油烟机开启和关闭状态下,模拟烹饪油烟发生处和3 m外位置处,0.03~10μm范围内油烟颗粒数浓度和质量浓度随粒径分布.油烟颗粒主要以655 nm以下的细颗粒为主.油烟机能够显著降低室内油烟浓度,开启油烟机后,油烟发生处颗粒数浓度从2.8×106个·cm-3降低到2.3×105个·cm-3,PM2.5(空气动力学直径≤2.5μm的颗粒)质量浓度从85.9 mg·m-3降低到6.2 mg·m-3.油烟机对PM10的净化效率高于PM2.5.油烟迅速从发生处扩散到3 m外,无通风状态下,总颗粒数浓度衰减达65%,PM2.5质量浓度衰减达75%.计算流体动力学(CFD)模拟了油烟机对油烟PM2.5质量浓度场扩散分布影响.红外摄像仪监测了油烟温度场分布扩散,以扇形向外扩散,伴随着油烟温度梯度降低.     

我国人为源气态活性氮排放时空变动特征分析

随着粮食和能源需求的增加,农业生产和化石燃料燃烧带来的活性氮污染越来越成为影响我国环境和人民健康的重要因素之一.通过对2000、2005及2010年全国31个省(直辖市、自治区)的人为源气态活性氮排放总量、单位GDP及单位人均排放量的Moran's I指数和GetisOrd G*i指数进行空间分析,探讨了气态活性氮排放及其强度的时空变动特征.结果表明,全国的气态活性氮排放及其强度呈现明显的空间集聚特征.在空间分布特征上,全国活性氮排放表现为高值集聚分布,其热点主要位于华北平原和长江中下游平原地区;排放强度方面则为高值聚集和低值聚集兼备.通过对3个年份的冷热点比较分析发现,排放强度的冷点地区变化较小,热点地区变化较大.其中,单位GDP排放强度方面,冷点地区处于东南沿海地区,热点地区则由西北地区缩小到四川、甘肃两省;而单位人口排放强度方面,冷点地区范围有所缩减,热点地区则由分散转变为集中分布于京津冀及周边的山西、内蒙古和辽宁等.分析人为源气态活性氮时空分布格局和特征及其形成原因,可为评估和减缓气态活性氮排放对生态环境的影响提供科学基础.     

双层板桁钢梁应力分析

以跨度最大的双层斜拉桥闵浦大桥为背景,研究了双层板桁钢梁桥面板的受力特性,阐述了精细壳单元与梁单元结合的整体有限元模型,并分析了上、下桥面间腹杆的受力特性与桥面板的应力分布特性;采用桥面纵横梁间带U肋精细桥面模型,分析了桥面板和U肋在车辆荷载作用下的应力分布.研究表明,上、下层桥面横桥向应力小于纵桥向应力,并且横桥向应...     

设置限位器双向隔震铁路桥梁车桥耦合动力响应研究

对铅芯橡胶双向隔震铁路桥梁在列车荷载作用下的力学性能进行了研究,针对双向隔震铁路桥梁中存在的问题,提出了设置限位器的解决方案,并对设置限位器的双向隔震铁路桥梁进行了车桥耦合动力响应分析.研究结果表明,采用常规隔震设计方法的铅芯橡胶支座在横桥向的初始刚度和屈服强度均不能满足规范要求,设置限位器后,双向隔震铁路桥梁的力学性...     

不同构造措施的钢管混凝土边框钢板剪力墙抗震性能试验研究

钢管混凝土边框钢板剪力墙是一种新型抗震剪力墙,为了比较不同构造措施对该新型剪力墙抗震性能的影响,进行了3个剪跨比为1.5的钢管混凝土边框钢板剪力墙低周反复荷载试验.其中,试验模型1为墙体钢板与边框柱钢管焊接,试验模型2为墙体钢板与边框柱钢管螺栓连接,试验模型3为墙体钢板开孔并与边框柱钢管焊接.通过试验研究,比较了各剪力...     

湖北省某钢铁厂工业区及周边铅污染调查

为了解湖北省某钢铁厂周边铅污染的现状,通过对钢铁厂工业区及其周边乡村的土壤、蔬菜、居民体内和排污渠污泥中铅元素含量的研究,其结果表明:钢铁厂周围的土壤、蔬菜、居民均受到了一定程度的铅等重金属元素的污染,其含量高于国家标准或正常范围;钢铁厂工业区周边土壤铅污染主要由于工业废气(烟尘)扩散沉降和废水灌溉引起;污染区人体尿样中铅元素含量(116～160 ng/mL)普遍超标,头发样(2.09～12.04 μg/g)基本正常,尿样比头发样更能显示铅等重金属元素在人体内的分布特征.