发酵类抗生素废水处理工艺及运行效果

介绍了内蒙古某抗生素废水处理厂的处理工艺流程、处理单元类型及其详细设计参数,通过对该污水处理厂半年内运行效果的调研,分析评价该污水处理系统的处理效果及出水指标;该水厂工艺流程对COD、TOC、氨氮、总氮、总磷、BOD和急性毒性的平均去除率分别为96.52%、95.83%、50.24%、55.20%、62.05%、98.52%和99.14%,COD、氨氮、总氮、总磷出水水质分别为477、438、556.7和7.69 mg/L,达到排放到城区下水道要求,园区内所有废水汇集到园区污水处理厂进行集中深度处理达标后排放水体。通过对该水厂工艺的介绍和水质分析,为我国抗生素生产企业面临的废水处理工艺类型选择及工程改造升级提供一定参考。     

Influence of constant and fluctuating temperature on biodegradation rates of fish biodiesel blends contaminating Alaskan sand

Bioremediation of sandy soil contaminated with fish-biodiesel, conventional diesel, and blends of both was studied in microcosm experiments at different temperatures, simulating the subarctic environment. While distinct lag, exponential, and stationary phases were observed at 20 °C, degradation at 6 °C was slow and the lag phase continued throughout the 4-week experiment. A three-phase 1st order kinetic model successfully described respiration at 20 °C, a one-phase model was sufficient at 6 °C. For temperatures fluctuating between ∼6 and ∼20 °C, higher than expected microbial activity persisted at 6 °C for several days, due to the presence of active cultures, even though the soil temperature closely followed the air temperature. At 20 °C, respiration peaked already after 1 week, and 18-51% of the initially added fuel was mineralized within 4 weeks, whereby degradation was higher at higher biodiesel percentages. Biodiesel addition accelerated mineralization of blends with regular diesel beyond expectations. In blends with 20% biodiesel, the degradation rate constant was twice as high as for conventional diesel. These synergistic effects are likely due to an active microbial population. Addition of biodiesel to conventional diesel could reduce the impact of diesel spills.     

Does the Temporal Resolution of Precipitation Input Influence the Simulated Hydrological Components Employing the SWAT Model?

This study aimed to evaluate the influence of sub‐daily precipitation time steps on model performance and hydrological components by applying the Green and Ampt infiltration method using the Soil and Water Assessment Tool (SWAT). Precipitation was measured at a resolution of 0.1 mm and aggregated to 5‐, 15‐, 30‐, and 60‐min time steps. Daily discharge data over a 10‐year period were used to calibrate and validate the model. Following a global sensitivity analysis, relevant parameters were optimized through an automatic calibration procedure using SWAT‐CUP for each time step. Daily performance statistics were almost equal among all four time steps (NSE ≈ 0.47). Discharge mainly consisted of groundwater flow (55%) and tile flow (42%), in reasonable proportions for the investigated catchment. In conclusion, model outputs were almost identical, showing simulations responded nearly independently of the chosen precipitation time step. This held true for (1) the selection of sensitive parameters, (2) performance statistics, (3) the shape of the hydrographs, and (4) flow components. However, a scenario analysis revealed that the precipitation time step becomes important when saturated hydraulic conductivities are low and curve numbers are high. The study suggests that there is no need in using precipitation time steps <1 h for lowland catchments dominated by soils with a low surface runoff potential if daily flow values are being considered. Editor's note : This paper is part of the featured series on SWAT Applications for Emerging Hydrologic and Water Quality Challenges. See the February 2017 issue for the introduction and background to the series.     

Long-range atmospheric transport of three toxaphene congeners across Europe. Modeling by chained single-box FATEMOD program

Background, aims, and scope  Since toxaphene (polychlorocamphene, polychloropinene, or strobane) mixtures were applied for massive insecticide use in the 1960s to replace the use of DDT, some of their congeners have been found at high latitudes far away from the usage areas. Especially polychlorinated bornanes have demonstrated dominating congeners transported by air up to the Arctic areas. Environmental fate modeling has been applied to monitor this phenomenon using parallel zones of atmosphere around the globe as interconnected environments. These zones, shown in many meteorological maps, however, may not be the best way to configure atmospheric transport in air trajectories. The latter could also be covered by connecting a chain of simple model boxes. We aim to study this alternative approach by modeling the trajectory chain using catchment boxes of our FATEMOD model. Polychlorobornanes analyzed in biota of the Barents Sea offered one case to study this modeling alternative, while toxaphene has been and partly still is used massively at southern East Europe and around rivers flowing to the Aral Sea. Materials and methods  Pure model substances of three polychlorobornanes (toxaphene congeners P26, P50, and P62) were synthesized, their environmentally important thermal properties measured by differential scanning calorimetry, as evaluated from literature data, and their temperature dependences estimated by the QSPR programs VPLEST, WATSOLU, and TDLKOW. The evaluated property parameters were used to model their atmospheric long-range transport from toxaphene heavy usage areas in Ukraine and Aral/SyrDarja/AmuDarja region areas, through East Europe and Northern Norway (Finnmarken) to the Barents Sea. The time period used for the emission model was June 1997. Usual weather conditions in June were applied in the model, which was constructed by chaining FATEMOD model boxes of the catchment’s areas along assumed maximal air flow trajectories. Analysis of the three chlorobornanes in toxaphene mixtures function as a basis for the estimates of emission levels caused by its usage. High estimate (A) was taken from contents in a Western product chlorocamphene and low estimate (B) from mean contents in Russian polychloroterpene products to achieve modeled water concentrations. Bioaccumulation to analyzed lipid of aquatic biota at the target region was estimated by using statistical calculation for persistent organic pollutants in literature. Results  The results from model runs A and B (high and low emission estimate) for levels in sea biota were compared to analysis results of samples taken in August 1997 at Barents Sea. The model results (ng g⁻¹ lw): 4–95 in lipid of planktovores and 7–150 in lipid of piscivores, were in fair agreement with the analysis results from August 1997: 21–31 in Themisto libellula (chatka), 26–42 in Boreocadus saida (Polar cod), and 5–27 in Gadus morhua (cod) liver. Discussion  The modeling results indicate that the application of chained simple multimedia catchment boxes on predicted trajectory is a useful method for estimation of volatile airborne persistent chemical exposures to biota in remote areas. For hazard assessment of these pollutants, their properties, especially temperature dependences, must be estimated by a reasonable accuracy. That can be achieved by using measurements in laboratory with pure model compounds and estimation of properties by thermodynamic QSPR methods. The property parameters can be validated by comparing their values at an environmental temperature range with measured or QSPR-estimated values derived by independent methods. The chained box method used for long-range air transport modeling can be more suitable than global parallel zones modeling used earlier, provided that the main airflow trajectories and properties of transported pollutants are predictable enough. Conclusions  Long-range air transport modeling of persistent, especially photo-resistant organic compounds using a chain of joint simple boxes of catchment’s environments is a feasible method to predict concentrations of pollutants at the target area. This is justified from model results compared with analytical measurements in Barents Sea biota in August 1997: three of six modeled values were high and the other three low compared to the analysis results. The order of magnitude level was similar in both modeled (planktovore and piscivore) and observed (chatka and polar cod) values of lipid samples. The obtained results were too limited to firm validation but are sufficient to justify feasibility of the method, which prompts one to perform more studies on this modeling system. Recommendations and perspectives  For assessment of the risk of environmental damages, chemical fate determination is an essential tool for chemical control, e.g., for EU following the REACH rules. The present conclusion of applicability of the chained single-box multimedia modeling can be validated by further studies using analyses of emissions and target biota in various other cases. To achieve useful results, fate models built with databases having automatic steps for most calculations and outputs accessible to all chemical control professionals are essential. Our FATEMOD program catchments at environments and compound properties listed in the database represent a feasible tool for local, regional, and, according our present test results, for global exposure predictions. As an extended use of model, emission estimates can be achieved by reversed modeling from analysis results of samples corresponding to the target area. This article is dedicated to the memory of Professor Alexander B Terentiev (who passed away in November 2006), our true friend. With his Institute of Organo-Element Compounds, Russian Academy of Science, Moscow, he was an important main organizer of the six joint Finnish–Russian seminars (every third year since 1989) on the field (‘Chemistry and Ecology of Organo-Element Compounds’). He prompted us especially to search properties and environmental fates for various polyhalogen compounds. We remember him for his friendly character and great sense of humor.     

三级串联人工快渗系统处理养殖废水

人工快速渗滤系统（constructed rapid infiltration,CRI）是在传统的污水快速渗透系统上发展起来的一种新的生物处理方法。采用猪粪浸泡污水模拟实际猪场处理系统的厌氧出水,研究三级串联人工快渗系统对其污染物的去除效果。试验结果表明,三级串联系统对废水COD、NH3N的去除率稳定在81%和94.5%,出水均满足了《畜禽养殖行业污染物排放标准》（GB18596-2001）的要求,同时三级串联系统还可以有效预防系统的堵塞。     

无砾石微孔管地下渗滤系统处理生活污水的中试研究

进行了无砾石微孔管地下渗滤系统处理生活污水的中试研究。基于不同土壤、不同管径、不同植物的协同效应,对比研究了不同系统处理污水中有机物、氮、磷和SS的去除效果及其影响因素。结果表明,不同土壤、不同管径及不同植物组成的系统,对生活污水中有机物、氮、磷和SS的去除效果差别较大。中试系统对COD、总磷、氨氮、总氮和SS的最佳去除率分别达到86.13%、90.20%、61.24%、65.49%和97.43%,对应的出水COD、总磷、氨氮、总氮和SS的平均浓度分别为64.29、0.69、22.13、26.19和5.56 mg/L。分析表明,进水SS浓度过高、外界温度下降等共同作用是导致系统对生活污水中NH4+-N和TN的去除率相对较低的主要原因。     

生物填料地下渗滤系统对生活污水的脱氮

将草甸棕壤、炉渣和活性污泥等基质按体积比13∶6∶1配制生物填料,研究了生物填料地下渗滤系统（subsurface wastewater infiltration system,SWIS）在不同的水力负荷和污染负荷条件下对校园生活污水的脱氮效果。场地实验结果表明,当BOD5负荷为12.0 g BOD5/（m2·d）,表面水力负荷为0.04-0.10 m3/（m2·d）时,SWIS对NH＋4-N和TN的平均去除率分别为92.4%和82.0%。当水力负荷为0.08 m3/（m2·d）,BOD5负荷9.3-16.8 g BOD5/（m2·d）时,SWIS对NH＋4-N和TN的平均去除率为92.7%和81.2%。SWIS中氧化还原电位（oxygen reduction potential,ORP）随进水水力负荷和BOD5负荷的增加而降低,脱氮效率下降。综合出水水质和处理效率,适宜的水力负荷和污染负荷分别为0.065 m3/（m2·d）和12.0 g BOD5/（m2·d）。在此条件下,SWIS的启动周期为25-30 d。出水水质均优于《城市污水再生利用-景观环境用水水质》（GB/T18921-2002）标准,且处理效果稳定,抗负荷冲击能力强。     

深型地下土壤渗滤系统中氮的去除途径

为了系统研究氮在深型地下土壤渗滤系统中的去除途径,本次实验采用直径30cm,高200cm的有机玻璃柱模拟地下土壤渗滤系统;柱内分层装填取自北京顺义的土壤。在水力负荷为8cm／d的条件下,取得了较好的脱氮效果;氨氮去除率为99．80％;TN去除率为83．68％。通过观察氮沿土柱深度的变化规律发现,在1．30m以上的区域随着氨氮浓度的降低硝氮浓度逐渐增大,同时总氮浓度也在不断降低,约有30．55％在此区域被去除;通过氮元素质量平衡证明这部分氮是通过厌氧氨氧化反应去除的。在1．30m以下反硝化反应是脱氮的主要途径,在此过程中难降解有机物被利用。     

考虑人为因素的可靠性评估

统计数据表明,系统的可靠运行不可忽略人为误操作造成的故障,该故障发生率有时甚至超过设备本身导致的系统故障发生率。将人为因素与设备自身因素造成的系统故障进行对比,分析人为因素造成系统故障后的特点,可得出人为因素的可靠性参数。根据解析法和模拟法的相关理论计算考虑人为因素的可靠性指标,可以看出考虑人为因素的计算结果更加符合实际运行特点,便于相关人员采取对策,保障系统的安全运行。     

生态土壤渗滤系统启动周期研究

利用室内模拟试验装置,考察了4种生态土壤渗滤系统在0.1 m3/(m2·d)的水力负荷条件下对生活污水中TP、COD和NH3-N的去除效果及启动周期; 同时对整个系统及同类生态工艺启动周期的判断方法做了探讨.研究结果表明,生态土壤渗滤系统对TP、COD和NH3-N的启动周期分别为15～27 d、24～40 d和24～26 d; 土壤渗滤系统对TP的启动周期最短,对COD的启动周期最长; 处理系统启动周期的判断原则是综合考察系统对主要污染物各自的启动周期,以最长的作为系统启动周期.4组试验中,1#和2#系统的启动周期为40 d; 3#和4#的为24 d.