树脂基纳米钛锆氧化物复合吸附剂同步去除水中磷和氟

以大孔强碱性阴离子交换树脂D201为基体,负载纳米钛、锆氧化物,制备新型树脂基纳米钛锆氧化物复合吸附剂TiZr-D201.通过吸附等温线实验、pH影响实验、竞争吸附实验、动力学实验及柱吸附实验,并结合对吸附剂的表征,探讨了复合吸附剂对水中磷和氟的吸附性能和相应的吸附机制.结果表明,当pH值为5.8,温度为308K时,Ti-Zr-D201对磷和氟的Langmuir拟合最大吸附容量分别是34.9 mg·g~(-1)和35.1 mg·g~(-1),且吸附行为是自发进行的,温度越高,吸附效果越好;与磷相比,pH值对Ti-Zr-D201吸附氟的影响更为显著;选取SO_4~(2-)、NO_3~-和Cl~-作为竞争离子,Ti-Zr-D201较基体D201表现出很好的抗干扰能力;内扩散模型拟合结果表明Ti-Zr-D201在吸附平衡前存在两个不同的吸附阶段;柱吸附实验表明Ti-Zr-D201具有稳定的结构和良好的动态吸附性能,并且可再生循环使用,具备实际应用的潜力.     

微生物燃料电池处理含S2-/NH4+废水的研究

以除硫硝化微生物燃料电池(Microbial Fuel Cell,MFC)处理含S~(2-)/NH_4~+的模拟无机废水,研究了不同进水S~(2-)浓度下MFC的产电性能、污染物去除效果和阳极室硫累积情况.结果表明,除硫硝化MFC可实现同步阳极除硫和阴极硝化,并通过非生物电化学作用和生物电化学作用共同产电.进水S~(2-)浓度为(60.8±2.9)、(131.7±2.4)、(161.7±4.5)和(198.1±3.1)mg·L~(-1)时,最佳阳极碳刷清洗周期分别为3、3、3、4个换水周期,前3个进水浓度下的换水周期可分别缩短为6、8和8 h.MFC阴极硝化完全,不受进水S~(2-)浓度影响,但氧从阴极向阳极的渗漏导致阳极库仑效率较低(40%).适当增加进水S~(2-)浓度可增强MFC的产电性能并提高S~(2-)去除负荷和颗粒硫累积比.除硫硝化MFC适宜的进水S~(2-)浓度为(161.7±4.5)mg·L~(-1),相应的最大功率密度为5.77 W·m~(-3),周期产电量为(141.0±5.2)C,S~(2-)去除负荷为(0.31±0.00)g·L~(-1)·d~(-1),颗粒硫累积比达58%.阳极碳纤维丝上沉积有粒径约100 nm的颗粒硫.阳极悬浮物与沉积物相比,悬浮物中S0含量比例较高,而S6+含量比例较低.     

土霉素对SBR系统细菌的抑制效应与机制研究

基于SBR系统,从脱氮过程、化学需氧量(COD)的去除过程、胞外聚合物(EPS)的总量变化过程、比呼吸速率(SOUR)的变化过程及微生物群落的变化等多个角度出发,较系统地研究了不同浓度土霉素对SBR系统的冲击作用.结果表明,由于土霉素(OTC)的作用,系统氨氮去除率从空白对照组的99.0%分别下降至77.2%(OTC 1 mg·L~(-1))、47.4%(OTC 5 mg·L~(-1))及10.0%(OTC 10 mg·L~(-1)).此外,高浓度土霉素(10mg·L~(-1))引起EPS分泌量和异养菌SOUR分别下降至空白组的44.3%和41.2%.由高通量分析可得,由于高浓度土霉素(5 mg·L~(-1)以上)的作用,活性污泥中微生物的多样性显著下降,且微生物的群落结构也发生显著变化.属层面的分析可得,高浓度土霉素(5 mg·L~(-1)以上)反应器中的部分氨氧化菌,如Nitrospira和Nitrosomonas均受到了抑制.     

抗生素废水的铁屑微电解预处理研究

研究了采用铁屑微电解法预处理抗生素废水.在进水COD质量浓度为6.2 g/L时,试验结果表明,经微电解处理后的废水,COD和色度的去除率分别达到68.3%和79.3%,BOD5/COD从0.306提高到0.56,废水的可生化性得到显著提高.通过正交试验考察pH、反应时间及铁屑用量对处理效果的影响,并对各因素作了单因素影响试验,确定了最佳工艺条件.     

不同条件下高炉渣吸附水中无机磷的研究

高炉渣(BFS)是在冶炼生铁过程中产生的固体废弃物,开展高炉渣的资源化研究具有重要意义.为了对水淬高炉渣净化含磷污水的应用提供理论依据,采取等温吸附的实验方法,比较了不同水淬炉渣的吸附磷效果,研究了不同pH和不同温度下水淬炉渣吸附磷的特点,结果如下:利用Langmuir等温吸附方程炉渣吸附磷的过程进行拟合,其相关系数均能达到显著水平.炉渣的碱度越高,吸附磷的效果越好;炉渣对磷的吸附能力随溶液pH的增加而降低,且初始为酸性(pH=2、4)的溶液在吸附达到平衡后pH有所上升,而初始为碱性的溶液(pH=10、12)在吸附达到平衡后pH有所下降;炉渣对磷的吸附是一个自发放热过程.     

A2/O工艺中的反硝化除磷

A2/O工艺是一种最简单的同步脱氮除磷工艺,但由于其系统中固有的基质竞争和污泥龄等矛盾,在实际应用中特别是处理低C/N比污水时脱氮除磷效率较低.反硝化除磷工艺作为近年来颇受关注的污水生物处理新技术.由于在脱氮除磷过程中可以在碳源利用上耦合,可从一定程度上缓解A2/O工艺中的基质竞争矛盾,使得其在处理低C/N比污水时也能实现较高的脱氮除磷效率.就反硝化除磷的技术原理,结合其在A2/O工艺中的最新研究成果及其控制策略,对A2/O工艺中的反硝化除磷的实现、维持及影响因素进行了分析和探讨,并对其发展方向进行了展望.     

In field arsenic removal from natural water by zero-valent iron assisted by solar radiation

An in situ arsenic removal method applicable to highly contaminated water is presented. The method is based in the use of steel wool, lemon juice and solar radiation. The method was evaluated using water from the Camarones River, Atacama Desert in northern Chile, in which the arsenic concentration ranges between 1000 and 1300 μg L⁻¹. Response surface method analysis was used to optimize the amount of zero-valent iron (steel wool) and the citrate concentration (lemon juice) to be used. The optimal conditions when using solar radiation to remove arsenic from natural water from the Camarones river are: 1.3 g L⁻¹ of steel wool and one drop (ca. 0.04 mL) of lemon juice. Under these conditions, removal percentages are higher than 99.5% and the final arsenic concentration is below 10 μg L⁻¹. This highly effective arsenic removal method is easy to use and inexpensive to implement.     

Impact of Bioaugmentation with a Consortium of Bacteria on the Remediation of Wastewater-Containing Hydrocarbons (5 pp)

Goals, Scope and Background It has been observed that hydrocarbon treated wastewaters still contain high COD and a number of intermediates. This suggests that the required catabolic gene pool for further degradation might be absent in the system or, that its titer value is not significant enough. By providing the desired catabolic potential, the overall efficiency of the treatment system can be improved. This study aims to demonstrate this concept by bioaugmentation of a lab-scale reactor treating refinery wastewater with a consortium having the capacity to complement the alkB genotype to the available microbial population. Methods Two reactors were set up using activated biomass collected from a refinery treatment plant and operated at a continuous mode for a period of 8 weeks. The feed to both reactors was kept constant. Crude oil was spiked regularly. One reactor was bioaugmented with a consortium previously described for crude oil spill remediation. The efficiency of the bioaugmented reactor was demonstrated by reduced COD. The changes in the microbial population over a period of time were analyzed by RAPD. Catabolic activity of the biomass in both reactors was monitored by PCR. The presence of the catabolic loci was confirmed by Southern Hybridization. Results and Discussion 52.2% removal of COD was observed in the bioaugmented reactor while only 15.1% reduction of COD was observed in the reactor without bioaugmentation. The change in microbial population can be seen from the 4th week, which also corresponds to improved catabolic activity. The presence of the bedA locus was seen in all samples, which indicates the presence of aromatic degraders, but the appearance of the alkB locus, from the 6th week onwards, which was observed only in the samples from the bioaugmented reactor. The results suggest that the gene pool of the bioaugmented reactor has catabolic loci that can degrade accumulated intermediates, thus improving the efficiency of the system. Conclusions In this study, improvement of efficiency of bioremediation was demonstrated by addition of catabolic loci that are responsible for degradation. Bioaugmentation was carried out in biomass that was collected from an ETP (effluent treatment plant) treating hydrocarbon containing wastewater to study the strategies for improvement of the treatment system. Biostimulation, only marginally improved the efficiency, when compared to bioaugmentation. The improved efficiency was demonstrated by COD removal. The presence of the alkB locus suggests the importance of a catabolic gene pool that acts on accumulated intermediates. It is well documented that straight chain aliphatics and intermediates of aromatic compounds after ring cleavage, accumulate in refinery wastewater systems, thereby hindering further degradation of the wastewater. Supplementation of a catabolic gene pool that treats the lower pathway compounds and alkanes will improve the overall efficiency. In this study, results suggest that the alkB locus can also be used to monitor the degradative mode of the activated biomass. Recommendations and Perspective . Pollution from petroleum and petroleum products around the globe are known to have grave consequences on the environment. Bioremediation, using activated sludge, is one option for the treatment of such wastes. Effluent treatment plants are usually unable to completely degrade the wastewater being treated in the biological unit (the aerator chambers). The efficiency of degradation can be improved by biostimulation and bioaugmentation. This study demonstrates the improved efficiency of a treatment system for wastewater containing hydrocarbons by bioaugmentation of a consortium that supports degradation. Further experiments on a pilot scale are recommended to assess the use of bioaugmentation on a large scale. The use of molecular tools, like DNA probes for alkB, to monitor the system also needs to be explored.     

Heavy metals in untreated/treated urban effluent and sludge from a biological wastewater treatment plant

Background, Aim and Scope

The presence of heavy metals in wastewater is one of the main causes of water and soil pollution. The aim of the present study was to investigate the removal of Cd, Cu, Pb, Hg, Mn, Cr and Zn in urban effluent by a biological wastewater treatment, as well as to quantify the levels of As, Be, Cd, Cr, Cu, Fe, Hg, Mn, Ni, Pb, Sn, Tl, V and Zn in dewatering sludge from the Biological Wastewater Treatment Plant to Ribeirão Preto (RP-BWTP), Brazil.

Materials and Methods

Concentrations of Cd, Cr, Cu, Mn and Pb in wastewater and those of Ni in sludge were determined by atomic absorption spectrophotometry with graphite furnace atomization. Mercury concentrations in wastewater were measured by hydride generation atomic spectrophotometry, and Zn levels were determined by atomic absorption spectrophotometry using acetylene flame. In sludge, the levels of As, Be, Cd, Cr, Cu, Fe, Hg, Mn, Pb, Sn, Tl, V and Zn were determined by inductively coupled plasma-mass spectrometry.

Results

The percentages of removal efficiency (RE) were the following: Hg 61.5%, Cd 60.0%, Zn 44.9%, Cu 44.2%, PB 39.7%, Cr 16,5% and Mn 10.4%. In turn, the mean concentrations (mg/kg) of metals in dewatering sludge followed this increasing order: Tl (<0.03), Hg (0.31), Be (0.43), As (1.14), Cd (1.34), V (59.2), Pb (132.1), Sn (166.1), Cr (195.0), Mn (208.1), Ni (239.4), Cu (391.7), Zn (864.4) and Fe (20537).

Discussion

The relationship between metal levels in untreated wastewater, as well as the removal efficiency are in agreement with previous data from various investigators, It is important to note that metal removal efficiency is not only affected by metal ion species and concentration, but also by other conditions such as operating parameters, physical, chemical, and biological factors.

Conclusions

Metal values recorded for treated wastewater and sludge were within the maximum permitted levels established by the Environmental Sanitation Company (CETESB), São Paulo, Brazil.

Recommendations

There is an urgent need for the authorities who are responsible for legislation on sludge uses in agriculture of establishing safety levels for As, Be, Hg, Sn, Tl and V.

Perspectives

According to the current metal levels, RP-BWTP sludge might be used for agriculture purposes. However, for an environmentally safe use of sewage sludge, further studies including systematic monitoring are recommended. Annual metal concentrations and predicted variations of those elements in the sludge should be monitored.

     

生物滤池对气相与液相中污染物质的净化

通过实验室研究探讨了生物滤池同时处理废水和废气的可行性。试验结果表明：在２５℃－３７℃条件下,甲苯废气的流量为９０Ｌ／ｈ,甲苯浓度为５００ｍｇ／ｍ＾３;废水的流量为０．４Ｌ／ｈ,ＣＯＤｃｒ浓度为４００－７５０ｍｇ／Ｌ,甲苯与ＣＯＤｃｒ的去除率分别是７０％－７２％和８６％－８９％。