Mixing hazard evaluation of organic peroxides with other chemicals

Organic peroxides (POs) have been widely used in chemical industries as initiators of polymerization, hardening or bridge formation agents, and they are known for its self-reactive and also mixing hazard characteristics when mixed with other chemicals such as acids and alkalis. It is the purpose of this investigation to propose a simple but useful evaluation flow of mixing hazards of POs with other chemicals using conventional experimental techniques such as a glass test tube test, Dewar vessel test and DSC is proposed. 7 kinds of POs (DEPD, THP, TBEH, TBTC, MEKPO, DTBP, THHP) were mixed with sulfuric acids with various concentration, sodium hydroxide solutions, -iron(III) oxide and acrylonitrile (AN).

Based on the proposed evaluation flow the testing results were classified into 4 ranks due to the hazard criteria. Futhermore DEPD/acrylonitrile mixtures were investigated in more detail and the influences of the mixing ratio and the stirring speed were discussed.     

City hazardous gas monitoring network

In our today's societies, many dangerous chemicals are produced and transported. Due to the vast use of chemicals, more chemical accidents are taking place with huge losses. In this study a city hazardous gas monitoring network was designed to detect the dispersion of toxic and combustible gases in the primary stages. The network could cover hazardous chemical facilities, important hazardous chemical routes, warehouses and special locations which may be the targets of terrorist attacks. The network is consisted of several local networks and a central control panel complex. Each local network has a local control panel in the center and many detectors and sounders around it at distances less than 3000 m that communicate with the local control panels wirelessly. In each location there are two types of gas detectors, toxic and combustible, and a sounder which are equipped with a wireless, radio frequency modem allowing the units to communicate readings and other information on a real-time basis with a remotely located local control panel. High sensitive Photo Ionization Detectors, PIDs, are used to provide fast and low-level on-site screening for chemicals contamination. Combustible gas detectors are the second choice to sense the combustible gas and verify the readings of PIDs in this regard. The central panel consists of several connected control panels work uniquely helping a computer set and the appropriate software and communicate with local control panels via telephone lines. All of the network components are shown on the monitor of central panel with special symbols by geographical information system program. The system is fully addressable so that the high level detection of a detector produces a blinking color double-circle around its symbol in GIS plan. In case of high level gas detection, a team of experts who are fully equipped with different portable detectors depart to the site to test the field to identify the chemicals. All readings of detectors are saved in a data bank and then analyzed to find any chemicals spills and leakages. The network was simulated by a special program so that the components of local networks and the central panel are shown in separate windows. By clicking on one detector on environmental window the formerly designed responses will be activated in central panel window.     

大学生沉溺网络透析及防范措施

因沉溺网上聊天、交友、玩游戏、看色情而影响大学生学习、生活、身体健康,以致诱发犯罪的问题如洪水猛兽席卷而来.防止大学生沉溺网络,走向犯罪是当前社会、学校、家庭不容忽视的问题.立法、执法、管理、教育应形成合力.     

Interconnectivity between the Superficial Aquifer and the Deep Confined Aquifers of the Gnangara Mound, Western Australia

Perth groundwater resources are obtained from three major aquifers that occur beneath the Perth metropolitan area: the Superficial aquifer, Leederville aquifer and Yarragadee aquifer. Each aquifer has a unique seasonal water level pattern controlled by soils, geomorphology and geology. Landuse is mainly responsible for variations in recharge; however, the hydraulic properties control aquifer response and water level pattern to a greater degree. Groundwater in the three aquifers is generally of very good quality except in localised areas. Salinity increases with depth and in direction of groundwater flow in the three aquifers. The best water quality is in the Superficial aquifer in the Wanneroo well field area. The geochemistry and stable isotope signatures from the three major aquifers revealed distinct water types that suggest very little hydraulic connection or mixing of waters between these aquifers at the present abstraction and recharge regimes. The results also show that the Leederville and Yarragadee aquifers were recharged during earlier cooler times while the Superficial aquifer is being recharged at present.     

GEOMORPHOLOGY OF STEEPLAND HEADWATERS: THE TRANSITION FROM HILLSLOPES TO CHANNELS1

Headwater streams comprise 60 to 80 percent of the cumulative length of river networks. In hilly to mountainous terrain, they reflect a mix of hillslope and channel processes because of their close proximity to sediment source areas. Their morphology is an assemblage of residual soils, landslide deposits, wood, boulders, thin patches of poorly sorted alluvium, and stretches of bedrock. Longitudinal profiles of these channels are strongly influenced by steps created by sediment deposits, large wood, and boulders. Due to the combination of small drainage area, stepped shallow gradient, large roughness elements, and cohesive sediments, headwater streams typically transport little sediment or coarse wood debris by fluvial processes. Consequently, headwaters act as sediment reservoirs for periods spanning decades to centuries. The accumulated sediment and wood may be episodically evacuated by debris flows, debris floods, or gully erosion and transported to larger channels. In mountain environments, these processes deliver significant amounts of materials that form riverine habitats in larger channels. In managed steepland forests, accelerated rates of landslides and debris flows resulting from the harvest of headwater forests have the potential to seriously impact the morphology of headwater streams and downstream resources.     

DRY AND WET WEATHER FLOW NUTRIENT LOADS FROM A LOS ANGELES WATERSHED1

Effective watershed management requires an accurate assessment of the pollutant loads from the associated point and nonpoint sources. The importance of wet weather flow (WWF) pollutant loads is well known, but in semi‐arid regions where urbanization is significant the pollutant load in dry weather flow (DWF) may also be important. This research compares the relative contributions of potential contaminants discharged in DWF and WWF from the Ballona Creek Watershed in Los Angeles, California. Models to predict DWF and WWF loads of total suspended solids, biochemical oxygen demand, nitrate‐nitrogen, nitrite‐nitrogen, ammonia‐nitrogen, total Kjeldahl nitrogen, and total phosphorus from the Ballona Creek Watershed for six water years dating from 1991 to 1996 were developed. The contaminants studied were selected based on data availability and their potential importance in the degradation of Ballona Creek and Santa Monica Bay beneficial uses. Wet weather flow was found to contribute approximately 75 percent to 90 percent of the total annual flow volume discharged by the Ballona Creek Watershed. Pollutant loads are also predominantly due to WWF, but during the dry season, DWF is a more significant contributor. Wet weather flow accounts for 67 to 98 percent of the annual load of the constituents studied. During the dry season, however, the portion attributable to DWF increases to greater than 40 percent for all constituents except biochemical oxygen demand and total suspended solids. When individual catchments within the watershed are considered, the DWF pollutant load from the largest catchment is similar to the WWF pollutant load in two other major catchments. This research indicates WWF is the most significant source of nonpoint source pollution load on an annual basis, but management of the effects of the nonpoint source pollutant load should consider the seasonal importance of DWF.     

BASE FLOW RECESSION RATES,LOW FLOWS,AND HYDROLOGIC FEATURES OF SMALL WATERSHEDS IN PENNSYLVANIA,USA1

This paper examines the relationships between measurable watershed hydrologic features, base flow recession rates, and the Q_7,10 low flow statistic (the annual minimum seven‐day average streamflow occurring once every 10 years on average). Base flow recession constants were determined by analyzing hydrograph recession data from 24 small (>130 km²), unregulated watersheds across five major physiographic provinces of Pennsylvania, providing a highly variable dataset. Geomorphic, hydrogeologic, and land use parameters were determined for each watershed. The base flow recession constant was found to be most strongly correlated to drainage density, geologic index, and ruggedness number (watershed slope); however, these three parameters are intercorrelated. Multiple regression models were developed for predicting the recession rate, and it was found that only two parameters, drainage density and hydrologic soil group, were required to obtain good estimates of the recession constant. Equations were also developed to relate the recession rates to Q_7,10 per unit area, and to the Q_7,10/Q₅₀ ratio. Using these equations, estimates of base flow recession rates, Q_7,10, and streamflow reduction under drought conditions can be made for small, ungaged basins across a wide range of physiography.     

BASE FLOW TRENDS IN URBANIZING WATERSHEDS OF THE DELAWARE RIVER BASIN1

Rapid land development is raising concern regarding the ability of urbanizing watersheds to sustain adequate base flow during periods of drought. Long term streamflow records from unregulated watersheds of the lower to middle Delaware River basin are examined to evaluate the impact of urbanization and imperviousness on base flow. Trends in annual base flow volumes, seven‐day low flows, and runoff ratios are determined for six urbanizing watersheds and four reference watersheds across three distinct physiographic regions. Hydrograph separation is used to determine annual base flow and stormflow volumes, and nonparametric trend tests are conducted on the resulting time series. Of the watersheds examined, the expected effects of declining base flow volumes and seven‐day low flows and increasing stormflows are seen in only one watershed that is approximately 20 percent impervious and has been subject to a net water export over the past 15 years. Both interbasin transfers and hydrologic mechanisms are invoked to explain these results. The results show that increases in impervious area may not result in measurable reductions in base flow at the watershed scale.     

Material flow analysis of lubricating oil use in California

Petroleum lubricating oils, used throughout the economy, are distinct among petroleum products in their capacity to be recovered and recycled at the end of their useful life. Used lubricating oil is regulated at the state and federal level because of concerns about environmental impacts arising from improper disposal, although rates of recovery are not known. We present a material flow analysis of lubricants through California's economy in the years 2007–2012. We introduce a novel technique for computing aggregate waste generation from a collection of hazardous waste manifest records, and apply it in order to determine a recovery rate for used oil and to estimate the quantity of oil managed informally in the state. The records also offer a detailed view of the fate of used oils after they are recovered. We find that around 62% of lubricants are recoverable at end of life, of which 70–80% is being recovered. This rate shows a slight downward trend. If the trend is accurate, measures should be taken to improve the performance of the used oil management system. Policy opportunities exist to reduce the quantity of oil managed informally through improving access to responsible used oil management methods. These include increasing the collection of used oil from industrial sources as well as “do it yourself” oil changes, expanding in-state reprocessing capacity, and promoting increased out-of-state reprocessing of used oil. Our methods introduce new possibilities to make use of direct observation in material flow analysis, potentially improving data availability and quality and increasing the relevance of material flow methods in policy applications.     

A transportation network assessment tool for hazardous material cargo routing: Weighing exposure health risks,proximity to vulnerable areas,delay costs and trucking expenses

The inherent risks associated with accidental releases of hazardous materials during transport have drawn attention and concerns in the recent decades. The aim of this study is to propose a tool for evaluation and comparison of the transportation networks which can be used to assess the routing options between origins and destinations of the cargos for their suitability for transporting hazardous material cargos by tanker trucks and to identify routes which provide lower accidental release risks, lower public exposure risks, and offer economical benefits. Each route segment of transportation networks were evaluated using specific criteria which included health risk and cost of delay in case of an accidental release of materials, trucking cost and proximity to vulnerable areas. Since, the health impact of hazardous materials differ depending on the characteristics of the material being transported as well as release quantities and atmospheric conditions; this paper aimed in providing a tool that can be used to estimate the impact radius (for health risks) after accidental release of hazardous materials by taking into account different atmospheric conditions based on the meteorological data and solar elevation angle. The Gaussian air dispersion model paired with ArcGIS using Python programming were employed to estimate the health risk impact zones by considering the meteorological data, and accordingly to analyze road segments for cost impacts (delay and trucking costs), and the proximity to vulnerable areas. The route assessment tool was demonstrated with a case study. The results of this study can efficiently aid decision makers for transportation of hazardous materials.