废钻井液污染分析及处理方法的探讨

为解决废钻井液对周围环境的污染,介绍了废钻井液的成分及对环境的影响,分析了国内外废钻井液处理方法的优缺点,详细阐述了中原油田结合本单位情况,用无害化处理技术处理废钻井液的方法和效果。试验表明：无害化处理剂中的各组分与废钻井液中各污染因子发生化学和物理作用,经３～５个月固化后可以达到无害化处理的目的。分析认为：中原油田钻井废弃物无害化处理技术是切实可行的。     

GPS/GSM/GIS海上溢油跟踪监测系统的研究

在车载GPS监控系统的基础E研究开发了一种漂浮移动性能与溢油相似的、并具有GPS接收和发送功能的GPS浮标。在溢油事故发生后立即将其投放存厚油膜层中随油膜一起漂移。监测中心通过GSM移动通信网实时接收GPS浮标发出的定位信息，并应用地理信息系统技术实现对溢油位置、漂移速度、轨迹、方向的实时跟踪和信息显示．从而为溢油应急指挥提供一种准确实时、成本低廉、全天候的溢油全程监测手段。     

用油品的物理特性鉴别海面的溢油源

建立了用油品的物理特性鉴别海面溢油源的分析方法。主要对海面溢油风化过程中溢油的运动粘度和折射率的变化进行了探讨。结果表明 ,在所给出的多个油种的风化过程中 ,油种间的运动粘度变化存在着明显的差异。随着风化时间的延长 ,原油的运动粘度随着风化时间的延长而显著增加 ,重质燃料油虽略有递增却很不明显 ;轻质燃料油和润滑油的运动粘度均在缓慢地增加。润滑油和燃料油的折射率无明显的变化。运动粘度法鉴别溢油的准确度较高 ,其准确率可达 10 0 %。     

炼化装置大型机组润滑油站油雾回收系统改造

针对炼化装置机组润滑油站油雾无法回收、现场卫生差及VOCs排放超标等问题,通过对几种油雾治理方式的分析比对发现,将离心式分离法和过滤法相结合可显著降低补油量,改善现场卫生,直接减少非甲烷总烃排放量,同时也为装置创造了一定的经济效益。     

Chemical degradation and biodegradability increase

The mill waste water holds a large amount of polyphenols, preventing the biodegradation processes because of their inhibitory action on microbial growth. Thus, its disposal represents an environmental problem for the great olive oil producing countries in the Mediterranean area. In this work, we present the preliminary results from the application of a photo-oxidative process on mill waste water to evaluate the organic matter degradation potential and the biodegradability of the treated residue. The total organic carbon is reduced up to 35% after 6 hours but the cost-effectiveness is unfavourable. In contrast, the aim of toxicity reduction is less expensive and shows good applicable chances; after 2 h, the polyphenols concentration drops by 60%.     

油泥废弃物的生物修复技术研究

本文利用正交试验 ,探讨了堆腐法处理油泥废弃物过程中调控因子 (肥料、客土、水分和 pH)的影响。结果发现 ,投加一定量的客土是影响处理效果的重要因子。通过正交试验选择和确定的最佳处理条件为 :在自然温度 >2 0℃的情况下 ,客土投加量 2 0 %、肥料 10 %、菌剂 5 %、控制水分 30 % (烘干基 )和pH 7。优化条件的建立为油泥废弃物的深度处理提供了理论依据     

堆肥法处理含油污泥研究进展

含油污泥是炼油厂和石油化工厂的日产固体废弃物 ,是当前石化行业所面临的污染问题。本文给出了近期国内外对含油污泥的处理方法 ,并对堆肥法处理含油污泥进行了综述。含油污泥的堆肥处理需提供氧气、菌种和营养 ,为保持油泥的疏松状态 ,还需加入填充剂。本文对高速生物反应器的结构、运行、调控进行了详细介绍 ,并从经济核算角度指出了其运营可行性     

海洋柴油溢油油水快速分离的应用研究

针对海洋柴油溢油,采用破乳剂对油水快速分离进行了研究.分别对油水比、温度、破乳剂量及存在Ca2 、Mg2 的影响因素,进行了系列油水快速分离试验,并测定了破乳剂作用下乳液的界面张力.试验结果表明,柴油溢油形成的乳液稳定性较差,油水分离较容易,但分离后的水中含油量较高.加入聚醚类非离子型破乳剂FA、FB、FC和FD,可达到油水低温、快速分离的目的,且分离后的水中含油量较低.随着破乳剂浓度的增加,界面张力降低,当破乳剂浓度达到临界胶束浓度(CMC)时,界面张力最小,脱水效果最好.Ca2 、Mg2 对聚醚类非离子型破乳剂的影响很小.     

Baseline study of methane emission from open digesting tanks of palm oil mill effluent treatment

Anthropogenic release of greenhouse gases, especially CO₂ and CH₄ has been recognized as one of the main causes of global warming. Several measures under the Kyoto Protocol 1997 have been drawn up to reduce the greenhouse gases emission. One of the measures is Clean Development Mechanisms (CDM) that was created to enable developed countries to cooperate with developing countries in emission reduction activities. In Malaysia, palm oil industry particularly from palm oil mill effluent (POME) anaerobic treatment has been identified as an important source of CH₄. However, there is no study to quantify the actual CH₄ emission from the commercial scale wastewater treatment facility. Hence, this paper shall address the CH₄ emission from the open digesting tanks in Felda Serting Hilir Palm Oil Mill. CH₄ emission pattern was recorded for 52 weeks from 3600 m³ open digesting tanks. The findings indicated that the CH₄ content was between 13.5% and 49.0% which was lower than the value of 65% reported earlier. The biogas flow rate ranged between 0.8 l min⁻¹ m⁻² and 9.8 l min⁻¹ m⁻². Total CH₄ emission per open digesting tank was 518.9 kg day⁻¹. Relationships between CH₄ emission and total carbon removal and POME discharged were also discussed. Fluctuation of biogas production was observed throughout the studies as a result of seasonal oil palm cropping, mill activities, variation of POME quality and quantity discharged from the mill. Thus only through long-term field measurement CH₄ emission can be accurately estimated.     

固体废弃物轮胎的热解技术

综述了国内外对废轮胎的处理状况，并详细地讨论了废轮胎热解技术的发展、分类以及典型工艺流程。热解技术主要包括油化技术、气化技术和炭化技术三种，并可制得衍生油、燃料气、碳黑等产品。分析了废轮胎热解工艺存在的问题，指出了如何开发环境友好的集成工艺是废轮胎热解工艺的发展方向。