EGSB-CANON工艺启动及动力学特性

采用EGSB（Expanded Granular Sludge Bed）反应器,在启动全程自养脱氮（CANON）工艺中通过改变曝气方式以及优化曝气/非曝气逐步实现CANON工艺的稳定运行.通过研究不同曝气/非曝气条件下CANON工艺的脱氮性能的变化,探究系统内不同污泥粒径中功能菌的活性,揭示EGSB反应器不同的运行条件以及系统内不同粒径的微生物聚集体在CANON工艺启动过程中的影响机制与菌群结构特性.结果表明,当恒定曝气量为0.5L/min,曝气/非曝气为2：1（60min：30min）时,实现了AerAOB（Aerobic Ammonia-Oxidizing Bacteria）与AnAOB（Anaerobic Ammonium-Oxidation Bacteria）协同脱氮的目的,并成功将NOB（Nitrite-Oxidizing Bacteria）的活性由3.41mgN/（h·gVSS）抑制到0.75mgN/（h·gVSS）.在对AnAOB的双底物（NO₂^--N和NH₄⁺-N）抑制动力学结果进行Haldane拟合时,得到NH₄⁺-N和NO₂^--N的半饱和常数（k_s）、抑制动力学常数（k_h）分别为106.8,331.9mg/L,272.4,66.61mg/L,相关性系数（R²）分别为0.98133和0.99142.在CANON污泥颗粒化形成过程中,污泥粒径在0.154~0.335mm范围内主要以AerAOB为主,污泥粒径在1mm以上主要以AnAOB为主.不同粒径下微生物聚集体的协同作用以及稳定的群落结构实现了CANON工艺的稳定运行.     

鼠李糖脂-热对污泥厌氧发酵中脱水性能的影响

为了探究鼠李糖脂以及低温热水解预处理污泥厌氧发酵过程对污泥脱水性能的改变,利用毛细吸水时间（CST）表征脱水性能指标,有机物溶出、粒径分布以及三维荧光光谱分析阐明脱水性能变化机制.研究发现在厌氧发酵之前,预处理后污泥脱水性能均会降低;厌氧发酵之后原污泥脱水性能降低,经过热水解的污泥脱水性能改善;粒径分布变化表明粒径减小是预处理污泥脱水性能变差的部分原因,发酵之后粒径增大对于污泥脱水性能改善不明显.溶解性有机物（SCOD）、溶解性碳水化合物（SC）以及溶解性蛋白质（SP）的溶出情况发现粒径的减小是由于预处理手段对污泥的有效破解.三维荧光平行因子分析（PARAFAC）表明,污泥预处理且厌氧发酵前后溶解性有机质（DOM）均包含类腐殖酸C1（386nm/462nm）和C3（342nm/438nm）、酪氨酸类蛋白C2（278nm/306nm）以及色氨酸类蛋白C4（290nm/358nm）.其中,类腐殖酸的增多是热水解污泥脱水性能变差的主要原因,厌氧发酵之后酪氨酸蛋白的积累是原污泥脱水性能变差的原因,类腐殖酸的分解是热水解污泥发酵后改善的原因.     

长期饥饿后SPNA微颗粒污泥系统性能恢复

为了确定长期饥饿后连续流一段式部分亚硝化-厌氧氨氧化（SPNA）工艺的性能恢复情况,采用连续流反应器,考察了在室温下（11~23℃）经历161d饥饿期的SPNA系统性能恢复策略的可行性及脱氮性能和菌群结构变化.通过控制DO浓度及进水氨氮负荷,逐渐实现亚硝酸盐氧化菌（NOB）的抑制和淘汰、氨氧化菌（AOB）和厌氧氨氧化菌（AnAOB）的活性恢复和富集.在68d内系统总氮去除率恢复至72.13%,氨氮去除率恢复至94.75%.微颗粒污泥（³200μm）的占比从42.04%升至60.98%.微生物群落结构分析发现,停止运行161d后系统Candidatus Kuenenia的相对丰度升至25.53%,表现出较强的抵抗饥饿条件的能力,系统恢复后其相对丰度逐渐降低,接近反应器饥饿前水平.AOB的高底物利用能力是系统恢复的前提,AnAOB活性的提高是系统恢复的关键.系统性能的成功恢复表明室温下161d饥饿期对系统造成的影响是可逆的,长期室温下储存SPNA污泥是可行的.     

Enhanced nitrogen removal upon the addition of volatile fatty acids from activated sludge by combining calcium peroxide and low-thermal pretreatments

This study investigated a combined low-thermal and CaO₂ pretreatment to enhance the volatile fatty acid (VFA) production from waste activated sludge (WAS). The fermentative product was added to a sequencing batch reactor (SBR) as an external carbon source to enhance nitrogen removal. The results showed that the combined pretreatment improved WAS solubilization, releasing more biodegradable substrates, such as proteins and polysaccharides, from TB-EPS to LB-EPS and S-EPS. The maximum VFA production of 3529 ± 188 mg COD/L was obtained in the combined pretreatment (0.2 g CaO₂/g VS + 70 °C for 60 min), which was 2.1 and 1.4-fold of that obtained from the sole low-thermal pretreatment and the control test, respectively. Consequently, when the fermentative liquid was added as an external denitrification carbon source, the effluent total nitrogen decreased to Class A of the discharge standard for pollutants in rural wastewater treatment plants in most areas of China.     

Flow analysis of major and trace elements in residues from large-scale sewage sludge incineration

Increase of sewage sludge (SS) has led to the construction of more incineration plants, exacerbating to the production of SS incineration residues. However, few studies have considered the mass balance of elements in large-scale SS incineration plants, affecting the residues treatment and utilization. In this study, flow analysis was conducted for major and trace elements in the SS, the fly ash (sewage sludge ash, SSA) and bottom ash from two large-scale SS incineration plants. The elemental characteristics were compared with those of coal fly ash (CFA), and air pollution control residues from municipal solid waste incineration (MSWIA), as well as related criteria. The results showed that the most abundant major element in SSA was Si, ranging from 120 to 240 g/kg, followed by Al (76–348 g/kg), Ca (26–113 g/kg), Fe (35–80 g/kg), and P (26–104 g/kg), and the trace elements were mainly Zn, Ba, Cu, and Mn. Not all the major elements were derived from SS. Most trace elements in the SS incineration residues accounted for 82.4%–127% of those from SS, indicating that SS was the main source of trace elements. The partitioning of heavy metals in the SS incineration residues showed that electrostatic precipitator ash or cyclone ash with high production rates were the major pollutant sinks. The differences in some major and trace elements could be indicators to differentiate SSA from CFA and MSWIA. Compared with related land criteria, the pollutants in SSA should not be ignored during disposal and utilization.     

Isolation and characterization of a strain with high microbial attachment in aerobic granular sludge

Aerobic granule is a special microbial aggregate associated with biofilm structure. The formation of aerobic granular sludge is primarily depending on its bacterial community and relevant microbiological properties. In this experiment, a strain with high microbial attachment was isolated from aerobic granular sludge, and the detailed characteristics were examined. Its high attachment ability could reach 2.34 (OD_600nm), while other low attachment values were only around 0.06-0.32, which indicated a big variation among the different bacteria. The strain exhibited a very special morphology with many fibric fingers under SEM observation. A distinctive behaviour was to form a spherical particle by themselves, which would be very beneficial for the formation and development of granular sludge. The EPS measurement showed that its PN content was higher than low attachment bacteria, and 3D-EEM confirmed that there were some different components. Based on the 16S rRNA analysis, it was identified to mostly belong to Stenotrophomonas. Its augmentation to particle sludge cultivation demonstrated that the strain could significantly promote the formation of aerobic granule. Conclusively, it was strongly suggested that it might be used as a good and potential model strain or chassis organism for the aerobic granular sludge formation and development.     

皂角苷和柠檬酸联合对市政污泥中重金属的去除与风险评价

污泥的重金属污染严重制约其资源化利用,为探讨皂角苷和柠檬酸联合淋洗去除污泥中重金属的效果,为污泥的资源化利用提供理论依据,以武汉市4个市政污泥样品(S₁、S₂、S₃、S₄)为研究对象,选取1%的皂角苷和0.1 mol/L的柠檬酸联合淋洗1~4次,对淋洗前后污泥中重金属Cu、Ni、Pb、Zn、Cd和Cr的含量和形态进行了分析,并运用M_F指数法和潜在生态风险指数法对淋洗后污泥中重金属的迁移性和环境效应进行了评价。结果表明:经过1次淋洗后,污泥中Zn的去除率最高,为71.04%(S₁),而Ni的去除率较低,为20%左右(S₂),污泥中Cr、Cu、Pb和Cd的最大去除率在23.16%~43.00%之间;经过4次淋洗后,污泥中Zn、Pb、Cr、Cu、Cd和Ni的去除率最高分别为84.79%、81.73%、80.77%、78.89%、56.71%和55.51%;经过淋洗后污泥中各重金属酸溶态所占的比例降至5.41%以下,污泥中Cu以残渣态和可氧化态为主,其他重金属以残渣态为主;皂角苷与柠檬酸联合淋洗后,污泥中重金属的M_F(移动性指数)和E_i(潜在生态风险指数)值下降,说明污泥中重金属的移动性、生物有效性和潜在生态风险减弱,其中污泥中Ni、Pb、Zn的潜在生态风险均由中降为低,污泥中Cu、Cr和Cd的潜在生态风险也有所降低;1.5 g/L的熟石灰对污泥淋洗废液中Cu、Ni的回收率在25%左右,对Pb、Zn、Cd、Cr的回收率在58%~80%之间。皂角苷和柠檬酸联合淋洗可以较好地去除供试污泥中的重金属,降低重金属的移动性和潜在生态风险。     

厌氧氨氧化颗粒污泥快速培养及其抑制动力学

为实现厌氧氨氧化颗粒污泥(ANAMMOX granular sludge,AGS)的快速培养,采用上流式厌氧污泥床(up-flow anaerobic sludge bed,UASB)工艺,在添加少量絮状厌氧氨氧化污泥(flocculent ANAMMOX sludge,FAS)的反应器内填充生物流离球作为填料,对ANAMMOX的启动及FAS的颗粒化进行研究.同时利用Haldane模型研究AGS的基质抑制动力学特性.结果表明,利用生物流离球作为填料,实现了ANAMMOX的启动,总氮去除率达85%以上,总氮容积负荷为0. 72 kg·(m3·d)-1,并在127 d内成功培养出直径1. 0～3. 0 mm的AGS.动力学研究表明,反应器内AGS对氨和亚硝酸盐的最大反应速率分别为1. 46 kg·(kg·d)-1和1. 76 kg·(kg·d)-1,半抑制速率分别是852. 2 mmol·L-1和108. 2 mmol·L-1.与絮状污泥相比,AGS能承受更高的氨和亚硝酸盐抑制浓度,并保持较高的反应速率.采用含有海绵的生物流离球作为填料,能有效加速反应器的启动,加快AGS的形成,对厌氧氨氧化工艺的实际运行具有积极的意义.     

粉煤灰和活性污泥对好氧填埋渗滤液组分的影响

通过在好氧反应器中添加粉煤灰和活性污泥来加速固体废物的降解。实验结果表明,添加粉煤灰不但改善了氧气扩散,而且增强了反应器对各种污染物的去除能力,对渗滤液中COD、NH4+、NO3-的去除率分别达到75%、68%和65%以上;添加活性污泥引入了一定量的微生物,也有利于固体废物的降解,渗滤液中COD、NH4+、NO3-的去除率分别达到了90%、65%和77%。因此,通过添加粉煤灰和活性污泥来加速固体废物降解是可行的。     

曝气生物滤池反冲洗污泥特性研究

研究了曝气生物滤池(BAF)反冲洗污泥的生物相组成、生物活性、沉降特性及絮凝性能。结果表明,BAF反冲洗污泥具有较强的生物活性和絮凝性能,将其作为生物絮凝剂预处理生活污水时,最佳投加量为0.05～0.1体积比(反冲水占混合液体积比),对污水中COD和SS的去除率分别为21.2%～26.8%和34.2%～37.5%,能够达到预处理目的。