废钻井液固化实验研究

利用经实验筛选的固化剂配方对废钻井液进行了固化处理的室内配方研究。结果表明,经该固化剂配方处理后的固结材料在水中浸泡5d后的浸出液在色度、化学需氧量、pH值、石油类、悬浮物含量和重金属含量等指标方面可达到国家《污水综合排放标准》(GB8978-1996)中的二级标准。     

水质自动监测中的质量保证与质量控制

质量保证与质量拉制是水质自动监测中十分重要的技术工作和管理工作，包括人员素质、运行与管理机制、试剂与标准溶液的配制及文件记录等。在实际工作中，监测人员可根据仪器的运行状况，定期对仪器进行校准、标准溶液的棱查、比对实验验证及试剂有效性检查，用以检查仪器的基线飘移情况。如果分析中出现一个异常值，它的前后均为正常值，这种数值大多是由仪器的进样、仪器内部试剂传输等原因所致，如果发生原因不明的数据异常，就要及时检查系统的各个环节并采集实际水样进行人工分析，直至查清原因，剔除异常值，并在周报中加以说明，以确保上报数据的准确性、精密性和可比性。     

Direct supercritical fluid extraction from water

Abstract

This paper describes the development of apparatus suitable for direct supercritical fluid extraction of organics from water. Results are presented for the extraction of pentachlorophenol present in water at concentrations of the order of 0.1 ppm. The effect of changes in apparatus design and supercritical fluid flow rate on recovery are discussed.     

Blast wave clearing behavior for positive and negative phases

The purpose of the research was to improve prediction of response of buildings to blast waves by including the negative phase and considering clearing of both positive and negative phases. Commonly used structural design practices, which trace their origins to military design manuals, often ignore the negative phase as well as positive phase clearing. For high explosive threats, this approach is conservative in most circumstances. However, negative phase clearing had not previously been studied for blast waves, and the implications for structural response had not been evaluated. This paper presents results of modeling negative phase blast clearing behavior for a typical blast wave and discusses the differences from positive phase clearing. The implications of including positive and negative phase clearing in building blast damage analysis are also investigated through single-degree-of-freedom (SDOF) analyses.Blast waves from explosion sources like a vapor cloud explosion (VCE), pressure vessel burst or high explosive exhibit both positive and negative phases, and the relative magnitude of the positive and negative phases varies among explosion sources and the specific circumstances of each source. A fully reflected blast wave is produced if an incident blast wave were to strike an infinitely tall and wide wall in a normal orientation. Both the positive and negative phases of the blast wave are enhanced by the reflection process. However, when an incident blast wave strikes a wall of finite size in a normal orientation, rarefaction waves are created at the edges of the wall, and the rarefactions sweep down from the roof and inward from sides. The rarefaction waves result in a clearing effect for both the positive and negative phases.Clearing relieves some of the applied blast load on the reflected wall for the positive phase. However, this is not always the case for the negative phase. As shown by the results presented in this paper, clearing may either relieve or enhance the applied negative phase blast load, depending on the duration of the blast wave and the wall dimensions.The impact of negative phase clearing on structural response for generic building components was also investigated. Nonlinear SDOF methods were used to characterize response in terms of peak positive and negative displacements. It was found that the influence of the negative phase is significant and the peak structural response can occur during negative (outward) displacement.     

油田井场废水配制压裂液处理技术实验研究

针对油田井场废水高悬浮物、高色度、高金属离子浓度的特征,以处理后配制压裂液为目标,通过p H值调节及无机高分子絮凝法对井场废水进行了处理实验。结果表明,碳酸钠作为优选的p H值调节剂,可以在较低的p H值条件下有效去除废水中的高价金属离子;无机絮凝剂聚合硫酸铁在强碱性条件下对于悬浮物、色度的去除效果明显优于聚合氯化铝。聚合硫酸铁絮凝法可以使井场废水达到配制压裂液用水的要求。     

Application of CFD on the sensitivity analyses of some parameters of the modified Hartmann tube

The aim of this work is to determine the influence of operating parameters such as the dispersion pressure, the ignition delay and height on the dust flammability. A Computational Fluid Dynamics (CFD) simulation, based on an Euler–Lagrange approach, was developed with Ansys Fluent™ and validated experimentally. Such analysis will facilitate the choice of the most conservative conditions for a flammability test. This paper is focused on a case study performed on wheat starch with the modified Hartmann tube. The dispersion process of the powder was studied with granulometric analyses performed in situ and high speed videos. Tests were performed with injections at gas pressure ranging from 3 to 6 bars and the evolution of the particle size distribution (PSD) was recorded at different ignition heights (5, 10 and 15 cm over the dispersion nozzle). The observations highlighted the presence of agglomeration/deagglomeration processes and dust segregation. Besides, a CFD simulation analysis was aimed at evaluating the impact of a set of parameters on the PSD and the local turbulence, which are closely linked to some flammability parameters. For this computational analysis, the CFD simulation was coupled with a collision treatment based on a Discrete Element Method (DEM) in order to consider the cohesive behavior of the combustible dust. Thus the results suggest performing the injection of the gases at approximately 5 bars for the flammability tests of wheat starch in order to obtain the finest PSD at a given ignition height. It is also shown that the finest PSD are obtained at 5 cm over the dispersion nozzle. However, the local instabilities and turbulence levels are so high during the first stages of the dispersion that the flame growth can be disturbed for short ignition delays. Moreover, the stabilization of the bulk of the dust cloud requires longer periods of time when the ignition sources are located at 15 cm. As a result, the recommended height to perform a flammability test is 10 cm in this case. Finally, this study proposes some tools that might improve the procedure of dust flammability testing.