Analysis of Roadside Inhalable Particulate Matter (PM10) in Major Korean Cities

A data analysis of three major Korean cities was conducted to assess roadside inhalable particulate matter 10 μm or smaller in aerodynamic diameter (PM₁₀), including temporal and meteorological variations, over a recent period of 4 to 6 years. The yearly roadside PM₁₀ concentrations presented a well-defined increasing trend or no trend depending on the roadside monitoring station. Most mean values exceeded or approximated the Korean standard of 70 μg/m³ per year for PM₁₀. A representative roadside diurnal trend was characterized by a distinct morning maximum. In most cases, the Sunday roadside concentrations were similar to or somewhat lower than the weekday concentrations, and the PM₁₀ concentrations presented a well-defined seasonal variation, with the maximum concentration in March. The monthly maximum concentrations observed in March were most likely attributable to Asian dust storms. In two metropolitan cities (Seoul and Busan), the frequency of days with roadside PM₁₀ concentrations exceeding the standard of 150μg/m³ per 24 h was much lower for the roadside monitoring stations than for the residential monitoring station, whereas in the third city (Daegu), this result was reversed. Interestingly, the average maximum concentrations observed for the roadside sites in Seoul and Busan during March were higher than those for the residential sites, suggesting that the roadside concentrations responded more to the dust storms than the residential areas. The relationship between the pollutant concentrations and five important meteorological parameters (solar radiation, wind speed, air temperature, relative humidity, and precipitation) showed that the number and type of meteorological variables included in the equations varied according to the monitoring station or season. Finally, the current results confirmed that attention should be given to the PM₁₀ exposure of residents living near roadways.     

Neurophysiological Effects Induced in the Nervous Tissue by Low-Frequency, Pulsed Magnetic Fields

Summary The influence of pulsed magnetic fields (PMF) on the properties of nervous tissue was investigated. Hippocampal slices or synaptosomes obtained from hippocampal tissue were used as model systems. The amplitude of potentials recorded in vitro from one of the hippocampal pathways (Schaffer collaterals that use glutamate as a neurotransmitter) was employed as a measure of the influence of magnetic fields on synaptic efficiency. The synaptic glutamate turnover and radioactive calcium accumulation were used as markers of the PMF influence on biochemistry of synaptic mechanisms. The exposure of hippocampal slices for 30 min to PMF amplified evoked potentials. While the frequency of 0.16 Hz exerted the strongest effect, lower (0.01, 0.07, 0.03 Hz) and higher (0.5 Hz) frequencies were much less effective. The enhancement of the neuronal excitability was correlated with significant increase in the neuronal spontaneous activity mediated by electrical synapses. The PMF-induced changes in the excitability of the tissue were accompanied by an increase in the synaptic turnover of glutamate. The release of radioactive D-Aspartate (a glutamate analog used as a marker for glutamate turnover) from the slices, and its uptake by synaptosomes were enhanced, and reduced respectively, following the stimulation with pulsed magnetic fields. The frequency which was the most efficient in amplification of evoked potentials (0.16 Hz) was also the most effective in the modulation of the release and uptake processes. The PMF-induced changes in neurotransmitter turnover coincided with an increase in ⁴⁵Ca²⁺ accumulation observed in hippocampal slices exposed to PMF.     

Effects of particle thermal characteristics on flame microstructures during dust explosions of three long-chain monobasic alcohols in a half-closed chamber

To reveal clearly the effects of particle thermal characteristics on flame microstructures during organic dust explosions, three long-chain monobasic alcohols, solid at room temperature and similar in physical-chemical properties, were chosen to conduct experiments in a half-closed chamber. In the experiments, the dust materials were dispersed into the chamber by air to form dust clouds and the hybrids were ignited by an electrical spark. A high-speed optical schlieren system was used to record the flame propagation behaviors. A fine thermocouple and an ion current probe were respectively used to measure the flame temperature profile and the reaction behaviors of the combustion zone. Based on the experimental results, combustion behaviors and flame microstructures in dust clouds with different thermal characteristics were analyzed in detail. As a result, it was found that the dust flame surfaces were completely covered by cellular structures that significantly increased the flame frontal areas. Flame propagated more quickly and the number of the cellular cells increased as increasing the volatility of the particles. On the contrary, maximum temperature and the thickness of the preheated zone decreased as increasing the volatility of the particles. According to the ion current profile, the particles in the preheat zone were pyrolyzed to intermediate radicals and the radicals' fraction in the higher volatile dust flame was higher than that in the lower volatile dust flame.     

电化学氢化物发生法处理含锑废水及对锑的回收

采用电化学氢化物发生法对模拟含锑废水进行处理,锑与水电解产生的氢形成氢化物从溶液中脱除,而后收集并加热分解锑化氢得到金属锑.实验表明,在酸性条件下对Sb(Ⅲ)去除效果较好,p H=4时去除率为76.1%.Sb(Ⅲ)与电解水产生的氢结合形成锑化氢从溶液中逸出是溶液中锑去除的最主要途径(回收率为66.2%),电沉积和吸附也对锑的去除做出少量贡献.Sb(Ⅴ)须预还原为Sb(Ⅲ)再氢化进行去除.试用了铅、石墨、钨这3种电解阴极材料,铅电极处理效果最佳.     

蠡河底泥中反硝化复合菌群富集及菌群结构研究

从无锡市滨湖区蠡河底泥中富集培养反硝化复合菌群,研究其在不同富集培养阶段TN、NO-3-N、NO-2-N、NH+4-N和COD动态变化,分析反硝化过程中气体释放总量、释放速率和成分,通过构建全长16S r DNA克隆文库研究其菌落结构.结果表明,反硝化复合菌群富集在阶段4时脱氮效果最佳,仅在9 h内,330 mg·L-1的TN负荷下,TN去除率达90.9%,NO-3-N去除率达100%,中间产物NO-2-N和NH+4-N积累量最少,分别为3.39 mg·L-1和16.64 mg·L-1,COD去除率达85%;释放气体260m L,气体主要成分为N2,同时还有少量的CH4和CO2等.富集培养反硝化复合菌群细菌属于Pseudomonadaceae科和Rhodocyclaceae科,为Proteobacteria门,OUT丰度分别为57.8%和31.6%,Pseudomonadaceae科是优势类群.     

容积负荷对ABR-MBR工艺反硝化除磷性能的影响

采用连续流ABR-MBR组合工艺处理生活污水,研究不同容积负荷(volume loading rate,VLR)对该工艺反硝化除磷性能的影响,获得最佳工艺参数.试验考察ABR进水容积负荷(以COD计,下同)分别为0.76、1.01、1.51和2.27 kg·(m~3·d)~(-1)时系统去碳脱氮除磷的性能,并在各ABR容积负荷条件下考察MBR容积负荷对MBR反应器硝化性能的影响.结果表明,在ABR进水容积负荷为1.51 kg·(m~3·d)~(-1)的条件下,系统A2隔室COD去除量最大,并在MBR容积负荷为0.462 kg·(m~3·d)~(-1)时,MBR反应器中实现了短程硝化,系统NH_4~+-N和TN去除率分别达到90%和72%以上,厌氧释磷量为7.41 mg·L~(-1),缺氧吸磷量达到15.42 mg·L~(-1),出水PO_4~(3-)-P浓度低于0.5 mg·L~(-1),这表明短程硝化更有利于强化ABR-MBR系统的反硝化除磷性能.     

福建省重点城市路面尘负荷及化学组成研究

采集并分析了福建省重点城市厦门、漳州、泉州和莆田城区具有代表性的57个地面扬尘和16个土壤样品的26种无机元素、8种水溶性离子和碳成分等组成.不同城市粒径≤100μm的路面尘负荷平均值在6.99 g.m-2与10.11 g.m-2之间,而粒径≤2.5μm的路面尘(PM2.5)负荷平均值在4.0 mg.m-2和12.5 mg.m-2之间.不同城市土壤尘和路面尘PM2.5中浓度最高的元素都是Si、Ca、Al、Fe和K,路面尘中Ca元素明显富集,而主要人为来源的重金属元素如Cu、Pb、Zn、Cr在路面尘PM2.5中的浓度显著高于土壤尘.漳州城区路面尘PM2.5中二次离子NH4+、NO3-和SO24-的含量明显高于其它地区,厦门、漳州和泉州城区路面尘PM2.5中Mg2+和Ca2+之间都存在显著的正相关关系.四城市路面尘中有机碳(OC)的含量均高于济南、石家庄以及北京地面扬尘OC的含量,元素碳(EC)的含量均低于北京地区路面扬尘EC的含量.泉州和莆田两地OC和EC的相关性较好,说明路面尘中OC和EC有相同或相似的来源.质量平衡结果显示泉州和莆田路面尘PM2.5中含量最高的是土壤尘,其次为有机物.按化学组成特征对路面尘PM2.5进行聚类解析,得到受大气沉降影响、受土壤尘影响、受大气沉降和土壤尘共同作用以及受土壤尘和建筑尘共同作用4类样品.     

Ethanol mediated As(III) adsorption onto Zn-loaded pinecone biochar: Experimental investigation, modeling, and optimization using hybrid artificial neural network-genetic algorithm approach

Organic matters (OMs) and their oxidization products often influence the fate and transport of heavy metals in the subsurface aqueous systems through interaction with the mineral surfaces. This study investigates the ethanol (EtOH)-mediated As(III) adsorption onto Zn-loaded pinecone (PC) biochar through batch experiments conducted under Box–Behnken design. The effect of EtOH on As(III) adsorption mechanism was quantitatively elucidated by fitting the experimental data using artificial neural network and quadratic modeling approaches. The quadratic model could describe the limiting nature of EtOH and pH on As(III) adsorption, whereas neural network revealed the stronger influence of EtOH (64.5%) followed by pH (20.75%) and As(III) concentration (14.75%) on the adsorption phenomena. Besides, the interaction among process variables indicated that EtOH enhances As(III) adsorption over a pH range of 2 to 7, possibly due to facilitation of ligand–metal(Zn) binding complexation mechanism. Eventually, hybrid response surface model–genetic algorithm (RSM–GA) approach predicted a better optimal solution than RSM, i.e., the adsorptive removal of As(III) (10.47 μg/g) is facilitated at 30.22 mg C/L of EtOH with initial As(III) concentration of 196.77 μg/L at pH 5.8. The implication of this investigation might help in understanding the application of biochar for removal of various As(III) species in the presence of OM.     

北京市铺装道路降尘污染特征及来源

为研究北京市道路降尘在不同季节的污染特征及来源,选取北京市4条典型道路得到64个采样点的道路尘样品,采集的道路尘样品经过预处理得到75 μm以下的颗粒物,经过再悬浮及实验室分析得到PM_2.5的粒径分布和化学成分谱.结果表明:不同采样高度及不同道路类型的颗粒物粒径大体分布规律一致,颗粒物质量频率存在三个峰值,分别为0.75 μm（微粒径）、2.50 μm（小粒径）、4.50 μm（大粒径）;各季节的降尘颗粒物的化学组分中质量分数最大的是元素,主要元素（含量>1%）季节变化为冬季>春季>秋季>夏季,元素富集因子法得到污染元素为Cr、Cd、Sn、Cu、Zn、Pb、As,双重元素为Bi、Ti、Ni、W、Mg、Ca、TI、Mo、V、Fe、Zr、Ba,其余16种为非富集元素;颗粒物中离子质量分数在夏季最大为9.31%,春季、秋季、冬季的离子质量分数相差不大,其中Ca2+、NO₃-、Cl-、SO₄2-占总离子质量的80%左右;碳素中w（OC）和w（EC）的季节变化均为夏季>秋季>春季>冬季,OC/EC[w（OC）/w（EC）]的季节变化规律为冬季>春季>秋季>夏季.不同季节w（OC）和w（EC）的相关性大小为夏季>秋季>春季>冬季.对PM_2.5中化学组分来源分析表明,污染元素受机动车和建筑尘影响较大,与机动车尾气相比,机动车磨损造成的污染也不容小视;燃煤影响一直存在,但供暖期污染有所改善.机动车尾气、建筑尘及土壤尘对离子均有贡献,在夏季土壤尘、建筑尘、二次反应的综合影响较大,春季土壤尘影响更为突出.碳在夏秋季节受汽车尾气和建筑尘的影响较大,夏季二次反应影响不大;冬季除气象因素外,燃煤和生物质燃烧也不可忽视;春季土壤尘影响较为突出.      

污染场地地下水抽出处理技术研究

地下水污染控制与修复是场地修复的重点内容。我国在地下水污染控制与修复领域尚处于起步阶段,简述了我国地下水污染场地类型、污染特点以及国外地下水污染控制与修复的主要技术,重点研究整理了国外最为常用的地下水修复技术,即抽出处理技术的技术原理、适用条件、技术优势和限制条件,以及系统设计与运行重点关注内容,为我国的地下水污染控制与修复技术研究和工程实践提供参考。