城市生活垃圾焚烧处理过程中重金属迁移规律研究

通过采集厦门2个垃圾焚烧发电厂进厂垃圾、渗滤液、飞灰、炉渣和烟气样品,分析垃圾组成成分及各组分的重金属含量,结果表明,垃圾中以厨余、橡塑类和纸类为主,共占到垃圾干基的78．08％,重金属含量大小次序为Zn〉Cu〉Pb〉Cr〉Ni〉Cd〉Hg;垃圾渗滤液中除Zn外,其他金属的含量都较低,一厂渗滤液中重金属Ni、Zn迁移量较大,分别达到24．46％和8．52％。二厂渗滤液中重金属的迁移有相同的趋势,但含量相对较高。垃圾焚烧后其重金属主要分布在飞灰和废渣中,烟气中的含量非常少,不同金属的含量均有差别,这与金属的性质有很大关系;通过浸出毒性分析,飞灰中重金属酸溶态含量多,容易浸出,属于危险废物。同时,不同烟气处理工艺产生的飞灰的重金属浸出量有很大差别。     

利用废弃物衍生燃料的热化学处理法制富含氢气合成气

为了探讨利用热化学方式从城市垃圾中制取富含氢气合成气过程的要素影响,解析氢气发生特性及其与主要影响要素之间的关系。在分析了城市生活垃圾组分特性的基础上,将其加工成组分均一的废弃物衍生燃料(refuse de-rived fuel,RDF),并在700、800和900℃等3个温度条件下,分别开展了RDF的热解、气化及水蒸汽气化等实验。研究表明,RDF的加工不但可有效降低垃圾含水率,还可将垃圾热值提高近1倍。温度和添加水蒸汽是从RDF中制取富含氢气合成气过程中的关键影响要素。其中,温度对氢气生成起到至关重要的决定作用,温度的提高对促进H2浓度的提高有利,同时,在气化过程中添加水蒸汽,可有效促进CO和H2等有价气体组分生成。在900℃的高温水蒸汽气化处理过程中,可获得H2浓度最高为34.13%的合成气。另外,800℃热解过程所产生的合成气热值最高,达到14 509 kJ/Nm3。     

半干法烟气脱硫除尘多级功能处理装置技术与应用

文中介绍了一种炉窑烟气调质、烟气除尘、烟气脱硫在一个单体结构中的一体化装置和在烟气除尘脱硫技术上的应用,并对该脱硫除尘装置与传统的半干法烟气脱硫除尘装置进行了比较。     

垃圾焚烧中抑制二恶英二次生成的方法探讨

根据生活垃圾焚烧技术中二恶英的生成机理,余热锅炉的烟气在低温区急冷可以避免二恶英在低温区的再次合成,但目前在余热锅炉烟气低温区急冷是不可行的。提出一种从垃圾焚烧系统设计上进行烟气的急冷,从而抑制二恶英低温区二次生成的新方法。     

高炉渣对Cd~(2+)的吸附性能

采用包头钢铁集团炼铁厂的高炉渣为吸附剂(粒径0.154 nm)对Cd2+进行吸附,运用SEM技术对吸附剂进行了表征,研究了初始Cd2+质量浓度、吸附剂加入量、吸附时间、吸附温度和废水pH对Cd2+去除率的影响,并探讨了吸附机理。表征结果显示:高炉渣吸附剂具有疏松多孔的特点,表面十分粗糙,比表面积较大。实验结果表明:当吸附温度为室温(28℃)、废水pH为7、初始Cd2+质量浓度为10 mg/L、吸附剂加入量为8 g/L、吸附时间为60 min时,Cd2+去除率达到98.55%;高炉渣对Cd2+的吸附符合拟二级动力学方程和Langmuir等温吸附模型,且吸附反应易发生。     

承德建龙3#高炉炉役后期安全生产特点

承德建龙3#高炉第1代炉役后期,炉身冷却壁大量损坏,炉缸部分冷却壁水温差超高,炉底、炉基温度达到安全警戒线,炉壳多处开裂变形,依靠外部打水维持生产的情况下,通过采取加强高炉操作,设备维护管理等技术措施,保证了高炉安全生产.     

Energy efficacy used to score organic refuse pretreatment processes for hydrogen anaerobic production

The production of hydrogen through Anaerobic Digestion (AD) has been investigated to verify the efficacy of several pretreatment processes. Three types of waste with different carbon structures have been tested to obtain an extensive representation of the behavior of the materials present in Organic Waste (OW). The following types of waste were selected: Sweet Product Residue (SPR), i.e., confectionary residue removed from the market after the expiration date, Organic Waste Market (OWM) refuse from a local fruit and vegetable market, and Coffee Seed Skin (CSS) waste from a coffee production plant. Several pretreatment processes have been applied, including physical, chemical, thermal, and ultrasonic processes and a combination of these processes. Two methods have been used for the SPR to remove the packaging, manual (SPR) and mechanical (SPRex). A pilot plant that is able to extrude the refuse to 200 atm was utilized. Two parameters have been used to score the different pretreatment processes: efficiency (ξ), which takes into account the amount of energy produced in the form of hydrogen compared with the available energy embedded in the refuse, and efficacy (η), which compares the efficiency obtained using the pretreated refuse with that obtained using the untreated refuse. The best result obtained for the SPR was the basic pretreatment, with η = 6.4, whereas the thermal basic pretreatment gave the highest value, η = 17.0 for SPRex. The best result for the OWM was obtained through a combination of basic/thermal pretreatments with η = 9.9; lastly, the CSS residue with ultrasonic pretreatment produced the highest quantity of hydrogen, η = 5.2.     

原子吸收石墨炉技术测定水中痕量阴离子洗涤剂

本文研究了用乙二胺铜(Ⅱ)—氯仿作为络合—萃取体系,石墨炉原子吸收技术间接测定水中痕量阴离子洗涤剂的一种方法。其检出限为2.0ug/1,加标回收率为89.6%～104.5%。具有选择性好、灵敏度高、快速简便等特点。同时还研究了水样的酸度和共存离子对测定的影响。对于用原子吸收进行有机分析具有一定的实际意义。     

胶布热空气连续硫化废气的焚烧处理

比较了胶布热空气连续硫化废气的几种处理方法，认为焚烧法是最有效的处理方法，并对应用该法处理废气的工艺原理、主要设备、余热回收是焚烧过程中诮注意的事项作了较详尽的阐述。     

A research on dioxin generation from the industrial waste incineration

By using fluidized-bed furnace and rotary-kiln+stoker furnace and four different kinds of industrial wastes such as waste wood, coffee mill, waste oils and waste plastics, we have drawn the following conclusions:

(1) A relationship between H6CBz and DXN is acquired, which is DXN=0.34×H6CBz^1.1.

(2) The following means of emission reduction can be considered. (a) Reduction of DXN and Cl accumulation within the furnace, (b) control by the incinerated object, (c) control through the precursors of H6CBz, (d) improvement through operational control, (e) ammonia injection into the high-temperature zone of the furnace seems to be effective in reducing DXN and (f) DXN concentration is high with CO above 1800 ppm, though it decreases with CO below ≈10 ppm.