利用矿化垃圾层预防和控制渗滤液导排系统堵塞

在卫生填埋场中,垃圾渗滤液导排系统堵塞普遍存在,悬浮固体形成的物理堵塞、有机物降解和金属离子沉淀导致的生物-化学堵塞是引起导排系统堵塞的关键因素.本文构建了"矿化垃圾+砾石层导排"的渗滤液下渗装置,通过矿化垃圾预处理渗滤液中悬浮固体和有机物以控制导排系统发生的物理和生物-化学堵塞.结果表明,在矿化垃圾层,渗滤液中化学需氧量(COD)和悬浮固体(SS)去除较多,去除率分别达到了85%和87%,并且Ca²⁺浓度也出现了波动较大的现象;然而,渗滤液在砾石层下渗过程中,其COD、SS和Ca²⁺浓度保持稳定.并且,砾石层可排水孔隙率在长期运行的过程中没有明显变化,表明渗滤液在砾石导排层没有形成明显的沉淀.与此同时,在没有添加矿化垃圾的对照组发现,砾石层可排水孔隙率减少最多的区段是渗滤液的进水点位(可排水孔隙率减少达到了53%),即渗滤液有机负荷最大处的饱和砾石层堵塞最为严重,其无机堵塞物主要是碳酸钙等.因此,在渗滤液流入砾石层前,采用矿化垃圾层部分饱和的方式对渗滤液中有机物和悬浮固体进行预处理,可以预防和控制渗滤液在砾石层形成沉淀堵塞.研究为填埋场的运行管理渗滤液导排系统堵塞提供了新的思路和方法.     

Characteristics of the stabilized/solidified municipal solid wastes incineration fly ash and the leaching behavior of Cr and Pb

Fly ash is a hazardous byproduct of municipal solid wastes incineration (MSWI). An alkali activated blast furnace slag-based cementitious material was used to stabilize/solidify the fly ash at experimental level. The characteristics of the stabilized/solidified fly ash, including metal leachability, mineralogical characteristics and the distributions of metals in matrices, were tested by toxic characteristic leaching procedure (TCLP), X-ray diffraction (XRD) and scanning electron microscopy-energy dispersive spectrometer (SEM-EDS) respectively. Continuous acid extraction was utilized to extract metal ions and characterize their leaching behavior. The stabilization/solidification procedure for MSWI fly ash demonstrates a strong fixing capacity for the metals by the formation of C-S-H phase, hydrated calcium aluminosilicate and ettringite. The stabilized/solidified fly ash shows a dense and homogeneous microstructure. Cr is mainly solidified in hydrated calcium aluminosilicate, C-S-H and ettringite phase through physical encapsulation, precipitation, adsorption or substitution mechanisms, and Pb is mainly solidified in C-S-H phase and absorbed in the Si-O structure.     

臭氧-曝气生物滤池深度处理垃圾焚烧渗滤液可行性研究

研究了臭氧-曝气生物滤池(BAF)代替纳滤和反渗透深度处理垃圾焚烧渗滤液达标排放的技术可行性.半间歇臭氧氧化试验表明,实验用水的可生化性随着氧化时间的增加而增加,色度及UV254, 15min内去除率分别达91%和64%;氧化时间为45min时COD去除率59%, 45min后COD去除较慢, 120min时去除率77%.确定臭氧氧化时间为1h,在同样臭氧浓度与流量下进行了臭氧-BAF处理垃圾焚烧渗滤液的连续实验.结果发现,此工艺对COD、色度和UV254的去除率分别可达75%,95%和90%,其中2/3运行时间里COD低于排放标准100 mg/L.其中出水色度可稳定保持在40度以下达标排放.经过进一步优化,臭氧-BAF有望用于垃圾焚烧渗滤液的达标处理.GC-MS检测表明烷烃,芳香族化合物及含氮杂环化合物是试验用水的主要污染物,臭氧-BAF能够有效去除后两类化合物,但难以去除烷烃.     

Comparative study on the efficiency and environmental impact of two methods of utilizing polyvinyl chloride waste based on life cycle assessments

Two processes of utilizing polyvinyl chloride （PVC） waste, an incineration process and a vacuum pyrolysis process, for energy conversion were compared to determine their efficiency and environmental perfor- mance. We carried out a life cycle assessment with each of the two processes to evaluate their environmental impact and defined the goals and limits of our remit. As well, we established an inventory of PVC waste from incineration and vacuum pyrolysis based on process analysis, data collection and calculations. The results show that electrical power output per unit mass of PVC waste in the incineration process was twice as high as that of the vacuum pyrolysis process. Incineration had a larger total environmental impact potential than vacuum pyrolysis. The total environmental impact potential of PVC waste from incineration was three times higher than that from vacuum pyrolysis. Incineration of PVC disposed 300 ng. 100 kgI of dioxins and vacuum pyrolysis 98.19 ng- 100 kgI of dioxins. As well, we analyzed the data for their uncertainty with results quantified in terms of three uncertainties： basic uncertainty, additional uncertainty, and computational uncertainty. The coefficients of variation of the data were less than 25% and the quality of the inventory data was acceptable with low uncertainty. Both PVC waste disposal processes were of similar quality and their results comparable. The results of our life cycle impact assessment （LCIA） showed considerable reliability of our methodology. Overall, the vacuum pyrolysis process has a number advantages and greater potential for development of PVC disposal than the incineration process.     

重钢LF炉除尘系统工艺分析与改建

论述了关于重庆钢铁股份有限公司炼钢厂LF炉除尘工艺的现状和系统的不足,并且就相关技术问题进行了分析与研讨,提出了相应的处理方案。     

三峡库区生活垃圾的重金属污染程度评价

长期以来,我国的城市生活垃圾处理与处置主要以填埋为主,且大部分为简易填埋或堆放,形成众多的垃圾堆放场。它们不仅影响周围的生态环境,而且威胁到居民的身体健康,特别是不少堆存的生活垃圾受到重金属元素不同程度的污染,任意放置可能会产生严重的后果,所以评价生活垃圾的重金属元素污染程度有助于垃圾堆放场的环境影响评价以及污染防治措施的提出。以三峡库区为例,通过测定三峡库区各个区县主要垃圾堆放场堆存生活垃圾的重金属元素含量, 包括砷、铅、铬、镉和汞,采用单因子评价和综合评价法确定三峡库区堆存生活垃圾的重金属污染程度,为库区的环境保护提供决策支持。     

国内电炉钢发展现状与应用前景

通过电炉铜与转炉铜能耗对比,突显了电炉钢的节能与环保优势,同时介绍了国内外电炉钢应用现状。随着社会工业化的发展所带来的钢铁积蓄量的增加,以及电炉钢技术的不断完善和发展,加之迎合国家低碳经济政策的实施,国内电炉钢发展具有广阔前景。     

印染污泥焚烧烟气污染控制案例分析

以广东省某两家印染厂的印染污泥焚烧项目为主要研究对象,从污泥处理技术路线、焚烧设备及烟气处理流程等各方面入手,对各厂印染污泥与煤混烧烟气中颗粒物、NOx、SO2、酸性气体(HF、HCl)和重金属等污染物的进行采样分析,并对各厂现有烟气污染物控制设施的运行效果进行调研,结果表明,布袋除尘的效果较为理想,除尘效率可达99%以上;使用印染废水作为吸收液的湿法脱硫技术对SO2及酸性气体的去除效果不理想;SNCR对NOx具有一定的去除效果,是一种较为经济、高效的脱硝技术;焚烧后,大部分重金属最终以飞灰的形式被除尘器去除,但仍有部分重金属如Hg在出口烟气中的浓度仍然很高,需要采取必要的措施控制烟气中的重金属. 此外,基于印染污泥焚烧实例分析,提出适于印染污泥与煤混烧烟气处理工艺流程.     

MESIP∗: Modelling environmental scenarios in ponds

MESIP is a fugacity model which can predict the fate of organic hydrophobic chemicals in aquatic ecosystems. In this paper a short introduction to the mathematical model is presented together with a more detailed listing of the required input data. Comparison of the calculated and measured fate of a fluorescent whitening compound in an artificial outdoor pond is shown     

不同加热方式下催化氧化甲苯的性能研究

研究考察了微波单模腔、多模腔与传统电炉三种不同加热方式下甲苯的催化氧化性能,分析不同加热方式下进出口气体温度和固定床反应温度的变化,并对实验前后的Cu-Mn-Ce/TiO2-分子筛催化剂进行了扫描电镜、X射线衍射和比表面积等表征测试.研究表明,相同工艺条件下电炉加热、微波多模腔与单模腔加热对甲苯的去除效率分别为77%、83%和94%,对应的床层反应温度为265℃、215℃和145℃,微波加热的选择性、"热点效应"和偶极极化作用提高了甲苯的降解效率并降低其氧化温度和工艺处理能耗,微波单模腔内高的能量密度显著提高了甲苯的氧化效率并降低反应温度.催化剂表征发现,微波加热对催化剂结构与活性组分的分布几乎没有影响,而电炉加热则导致催化剂表面烧结与活性组分团聚,微波加热下催化剂更大的比表面积有利于甲苯的吸附与氧化降解.