微电解工艺处理染料工业废水研究

该文研究了采用微电解工艺处理染料工业废水.经过微电解工艺处理的染料工业废水色度和化学需氧量(COD)去除率分别为93.94%和64.62%.废水的可生化性提高,生化速率常数K从0.02876提高到0.04754.微电解工艺预处理该染料工业废水的吨水运行成本为0.91元.     

二沉池设计补正

静沉试验法是常用的二沉池设计方法 ,但是仍存在一些问题。在分析大量有关资料的基础上 ,对该法作了较深入的研究。结果表明 ,静沉试验法能够体现二沉池的实际沉降行为 ,但对浓缩时间的解法需要加以纠正。该设计方法可以更好地应用于优化设计之中。     

介绍一种新编制的环境试验用相对湿度查算表

介绍了一种新的环境试验用相对湿度查算表及其编制目的、编制方法,该查算表用较小的篇幅实现更宽的温度和相对湿度的查算范围(与GB6999鄄86《环境试验用相对湿度查算表》比较)。该查算表中对风速与大气压的修正方法有与其他查算表不同的特点,它对提高相对湿度测量(查算)精度有一定的作用。     

影响污泥沉降比的因素及对策

对污泥沉降比在实践中的应用作了论述，并对污泥沉降比的影响因素及对策作了分析探讨，可为曝气池的运作管理提供参考。     

Monograph on desilting basins sizes estimation for hydropower projects

At times, various analytical and empirical approaches used to estimate the initial sizing of a desilting basin in a hydropower project would give very different results and the designer has to take a call judiciously. The purpose of this study is to develop a monograph based on Teaching–Learning-Based Optimization and Gravitational Search algorithm for a practical range of depth of desilting basins. The parameters commonly used in hydropower projects for estimation of desilting basins sizing and its efficiency are used in this study. The outcome is further verified using a list of mega hydropower projects. This study will be useful in fixing the best optimized dimension of desilting basins.     

非线性拉伸对甲烷-空气预混火焰燃烧特性的影响

使用定容燃烧弹与高速纹影照相系统研究了不同当量比下甲烷-空气预混气体的层流火焰燃烧特性。实验数据同时应用传统线性模型和非线性模型分析了不同当量比对球形扩展火焰的传播速率和马克斯坦长度的影响。结果显示:随着当量比的增加,层流燃烧速率先增大后减小,直到当量比为1.1时,火焰速率达到最大值。马克斯坦长度始终为正值,且随着当量比的增大而增大。在所有当量比条件下,线性和非线性方法计算的火焰速率大致相同,差值小于0.01 m/s;线性方法得到的马克斯坦长度均大于非线性模型计算的结果,并随着当量比的增大,两种方法得到的马克斯坦长度的差值更加显著。     

我国精密可控震源主动探测研究进展

精密可控震源对地发射扫频信号,通过高精度的观测系统获得记录资料,采用专门的数据处理方法来提取信号,获得地下介质的信息。介绍现有的一些数据处理方法,比如匹配滤波、反褶积、Wigner-Hough变换和时变滤波等,可以实现可控震源信号提取。并总结这些方法的优缺点。通过多次野外科学实验发现,精密可控震源技术是一种探测地下介质结构及变化的有效途径。针对精密可控震源探测的影响因素,还需要开展深入研究,以便于改善其探测距离和分辨能力。     

Experimental study of the evaporation of spreading liquid nitrogen

The investigation of cryogenic liquid pool spreading is an essential procedure to assess the hazard of cryogenic liquid usage. There is a wide range of models used to describe the spreading of a cryogenic liquid pool. Many of these models require the evaporation velocity, which has to be determined experimentally because the heat transfer process between the liquid pool and the surroundings is too complicated to be modeled. In this experimental study, to measure the evaporation velocity when the pool is spreading, liquid nitrogen was continuously released onto unconfined concrete ground. Almost all of the reported results are based on a non-spreading pool in which cryogenic liquid is instantaneously poured onto bounded ground for a very short period of time. For the precise measurement of pool spreading and evaporation weight with time, a cone-type funnel was designed to achieve a nearly constant liquid nitrogen release rate during discharge. Specifically, three nozzles with nominal flow rates of 3.4 × 10⁻² kg/s, 5.6 × 10⁻² kg/s and 9.0 × 10⁻² kg/s were used to investigate the effect of the release rate on the evaporation velocity. It is noted that information about the release rate is not necessary to measure the evaporation velocity in case of the non-spreading pool. A simultaneous measurement of the pool location using thermocouples and of the pool mass using a digital balance was carried out to measure the evaporation velocity and the pool radius. A greater release flow rate was found to result in a greater average evaporation velocity, and the evaporation velocity decreased with the spreading time and the pool radius.     

洪水作用下汽车的起动流速研究

针对洪水作用下汽车的起动条件开展了一系列的研究:首先分析部分淹没状态下汽车的受力情况,结合滑动平衡的临界起动条件建立相关方程,导出了洪水中汽车起动流速公式;然后在室内水槽中对三款模型车进行了一系列的起动试验。试验结果表明:对于同一款模型车,平行于水流方向放置时,起动流速与水深的相关性较好;并且水深越大,起动流速越小。接着运用试验资料率定了起动流速公式中的相关参数。最后采用模型相似率及率定后的计算公式估算了原型车辆在不同水深下的起动流速,两种方法所得的结果较为接近,故预测结果较为可靠。     

Description and evaluation of a model of deposition velocities for routine estimates of air pollutant dry deposition over North America.: Part I: model development

This paper describes the development of a detailed dry deposition model for routine computation of dry deposition velocities of SO₂, O₃, HNO₃ and fine particle SO₄²⁻ across much of North America. Four different dry deposition/surface exchange sub-models have been combined with the current Canadian weather forecast model (Global Environmental Multiscale model) with a 3 h time resolution and a horizontal spatial resolution of 35 km. The present model uses the US Geological Survey North American Land Cover Characteristics data to obtain fourteen different land use and five seasonal categories. The four sub-models used are a multi-layer model for gaseous species over taller canopy land-use types, a big-leaf model for gaseous species over lower canopies (including bare soil and water) and for HNO₃ under all surface types and, two different models for SO₄²⁻, one for tall canopies and the other for short canopies. All necessary parameters for each sub-model, chemical species, land-use and seasonal categories have been selected from available data libraries or from the values reported in the literature. The purpose for developing this model (referred to as the Routine Deposition Model (RDM)), when coupled with air concentration data, is to provide estimates of seasonal dry deposition, which can be combined with wet deposition to produce total deposition estimates. Model theory is discussed in this paper and model sensitivity tests and results will be presented in a companion paper.