EU Directive,ICNIRP Guidelines and Polish Legislation on Electromagnetic Fields

This review describes the general provisions of and the philosophy behind European Directive 2004/40/EC and ICNIRP (International Commission on Non-Ionizing Radiation Protection) guidelines. As an example of national legislation on the protection of workers against excessive electromagnetic field exposure, regulations established in Poland are summarized. The problems of a practical implementation of the Directive’s provisions are discussed.     

Synergy Between Visual and Auditory Signals and Its Influence on the Follow-Up Regulation Quality

The study aimed at verifying a hypothesis that supporting a visual signal of regulation deviation with an auditory one could improve the quality of regulation; the operator would have better information on machine operation. A special simulator was applied to follow-up tracking with a manual lever which controlled vertical movements of a cursor on a monitor screen. Simultaneously with visual information on screen, the operator was provided with an auditory deviation signal of pre-determined characteristics. 33 young males underwent the test. It was found that supporting a visual signal with an auditory one resulted in an improvement in the regulation quality by 5-6%, which proved synergy between those signals. The results may be used in designing tele- and servo-mechanisms, especially for remote control machinery, e.g., inspection robots or micromanipulators controlled by operators in a follow-up system.     

Simulation of Reflected and Scattered Laser Radiation for Designing Laser Shields

This paper presents a computer simulation of reflected and scattered laser radiation for calculating the angle of laser shields performed with the Laser Shield Solver computer program. The authors describe a method of calculating the shield angle for laser shields which protect workers against reflected and scattered laser radiation and which are made from different materials. The main assumptions of the program, which calculates and simulates reflected laser radiation from any material and which can be used for designing shield angles, are presented. Calculations are compared with measurements of reflected laser radiation. The results for one type of laser and different materials which interacted with a laser beam showed that the Laser Shield Solver was an appropriate tool for designing laser shields and its simulations of reflected laser radiation distribution have practical use.     

A Fuzzy Model for Assessing Risk of Occupational Safety in the Processing Industry

Abstract

Managing occupational safety in any kind of industry, especially in processing, is very important and complex. This paper develops a new method for occupational risk assessment in the presence of uncertainties. Uncertain values of hazardous factors and consequence frequencies are described with linguistic expressions defined by a safety management team. They are modeled with fuzzy sets. Consequence severities depend on current hazardous factors, and their values are calculated with the proposed procedure. The proposed model is tested with real-life data from fruit processing firms in Central Serbia.     

Analysis of Conditions and Organization of Work of Notebook Computer Users

Abstract

Aim. The aim of this study was to evaluate working conditions with a notebook computer (notebook) as a potential cause of musculoskeletal disorders. Material and methods. The study had 2 stages. The first one was a questionnaire survey among 300 notebook users. The next stage was an expert analysis of 53 randomly selected workstations. The questionnaire survey included questions about the participants, their working conditions, work organization and also duration of work with a notebook. Results and conclusions. The results of the research showed that most examined operators used a notebook as a basic working tool. The most important irregularities included an unadjustable working surface, unadjustable height of the seat pan and backrest, unadjustable height and distance between the armrests and no additional ergonomic devices (external keyboard, docking station, notebook stand or footstool).     

Disparity of a Seat Cushion and Its Influence on Postural Control

Properties of supporting surfaces of a seat have an influence on postural control. Centre of pressure (COP) displacement parameters reflect both the balance controlling process and movements of the centre of a mass of entire body. The subjects of the study were 9 healthy men. A seat cushion was examined with a 2-force platform setup. Force exertion at a seat pan and feet and COP displacement at a seat pan were measured to analyse postural control. Analysis of variance determined the differences in postural control depending on a cushion type among the subjects. Significant differences in COP displacement parameters were in COP trajectory length, medio-lateral COP displacement and COP velocity. The results of the study showed that foam cushion ensures better postural control.     

Analysis of underlying causes of investigated loss of containment incidents in Dutch Seveso plants using the Storybuilder method

In the Netherlands there are around 400 “Seveso” sites that fall under the Dutch Major Hazards Decree (BRZO) 1999. Between 2006 and 2010 the Dutch Labour Inspectorate's Directorate for Major Hazard Control completed investigations of 118 loss of containment incidents involving hazardous substances from this group. On the basis of investigation reports the incidents were entered in a tailor-made tool called Storybuilder developed for the Dutch Ministry of Social Affairs and Employment for identifying the dominant patterns of technical safety barrier failures, barrier task failures and underlying management causes associated with the resulting loss of control events. The model is a bow-tie structure with six lines of defence, three on either side of the central loss of containment event. In the first line of defence, failures in the safety barriers leading to loss of control events were primarily equipment condition failures, pre start-up and safeguarding failures and process deviations such as pressure and flow failures. These deviations, which should have been recovered while still within the safe envelope of operation, were missed primarily because of inadequate indication signals that the deviations have occurred. Through failures of subsequent lines of defence they are developing into serious incidents. Overall, task failures are principally failures to provide adequate technical safety barriers and failures to operate provided barriers appropriately. Underlying management delivery failures were mainly found in equipment specifications and provisions, procedures and competence. The competence delivery system is especially important for identifying equipment condition, equipment isolation for maintenance, pre-start-up status and process deviations. Human errors associated with operating barriers were identified in fifty per cent of cases, were mostly mistakes and feature primarily in failure to prevent deviations and subsequently recover them. Loss of control associated with loss of containment was primarily due to the containment being bypassed (72% of incidents) and less to material strength failures (28%). Transfer pipework, connections in process plant and relief valves are the most frequent release points and the dominant release material is extremely flammable. It is concluded that the analysis of a large number of incidents in Storybuilder can support the quantification of underlying causes and provide evidence of where the weak points exist in major hazard control in the prevention of major accidents.     

A new simple methodology for evaluation of explosion risk in underground coal mines

The key objective of this paper is the presentation of a new risk assessment tool for underground coal mines based on a simplified semi-quantitative estimation and assessment method.In order to determine the risk of explosion of any work process or activity in underground coal mines it is necessary to assess the risk. The proposed method is based on a Risk Index obtained as a product of three factors: frequency of each individual scenario P_ucm, associated severity consequences C_ucm and exposure time to explosive atmospheres E_ucm. The influence of exposure time is usually not taken into account up to now. Moreover, the exposure to explosive atmospheres may affect factors of hazardous event probability as much as its consequences. There are many definitions of exposure to explosive atmospheres but in the case of underground coal mines the exposure is defined as frequency risk of firedamp and coal dust. The risk estimation and risk assessment are based on the developed of a risk matrix.The proposed methodology allows not only the estimation of the explosion risk but also gives an approach to decide if the proposal investment is well-justified or not in order to improve safety.     

RAPID-N: Rapid natech risk assessment and mapping framework

Natech accidents at industrial plants are an emerging risk with possibly serious consequences. For the mitigation of natech risk, authorities need to identify natech prone areas in a systematic manner. In order to facilitate probabilistic natech risk mapping, a unified methodology was developed that is based on the estimation of on-site natural hazard parameters, determination of damage probabilities of plant units, and assessment of probability and severity of possibly triggered natech events. The methodology was implemented as an on-line, extensible risk assessment and mapping software framework called RAPID-N, which allows rapid local and regional natech risk assessment and mapping with minimal data input. RAPID-N features an innovative data estimation framework to complete missing input data, such as on-site natural hazard parameters and plant unit characteristics. The framework is also used for damage assessment and natech consequence analysis, and allows easy modification of input parameters, dynamic generation of consequence models according to data availability, and extension of models by adding new equations or substituting existing ones with alternatives. Results are presented as summary reports and interactive risk maps, which can be used for land-use and emergency planning purposes by using scenario hazards, or for rapid natech consequence assessment following actual disasters. As proof of concept, the framework provides a custom implementation of the U.S. EPA's RMP Guidance for Offsite Consequence Analysis methodology to perform natech consequence analysis and includes comprehensive data for earthquakes. It is readily extendible to other natural hazards and more comprehensive risk assessment methods.     

Quantitative assessment in safety reports of the consequences from the detonation of solid explosives

Safety reports are mandatory documents in member states of European Union whenever any threshold limits of amounts of either stored or processed hazardous substances are exceeded. After a short introduction to EU Seveso Directives on major-accident hazards involving dangerous substances and to the transposition and implementation by member states, with a brief comment on last 2012/18/EU Directive (also known as Seveso III directive), the paper focuses on drafting of safety reports for industrial activities involving solid explosives. Specifically, the quantitative assessment of consequences from detonation is tackled respect to the side-on overpressure and the debris production. Both direct and inverse problems are illustrated to determine respectively the overpressure value at a given distance, and the explosive amount that allows respecting the regulations. Their solution is based on either analytic or numerical techniques and being based on recent scientific publications on the matter either evaluates or zeroes nonlinear algebraic equations. The availability of these equations avoids grounding the consequences assessment on diagrams and nomograms that otherwise would lead to interpretation and usage errors besides avoiding the automatic solution of the inverse problem. The paper focuses also on details such as embankment, crater, munitions, rocket propellant, building structure, and wall material that, at different levels, play a role in the assessment of detonation consequences. A discussion on debris formation, the available literature, and the evaluation of the impact probability of fragments on both fixed and moving targets closes the paper.