兔子宫内膜蛋白等电聚焦电泳柱状胶与板状胶电泳效果的比较

哺乳动物早期胚胎发育过程中，胚泡附植的成功与否对早期胚胎的发育十分重要．为了有效地弄清胚泡附植的分子机制，本研究从分析蛋白质的一种生化技术-等电聚焦电泳着手，利用兔子宫内膜蛋白作为实验材料，探讨了柱状胶与板状胶等电聚焦电泳分离蛋白质的电泳效果．研究结果表明：在相同情况下，柱状胶与板状胶的蛋白质分布有一些差别，pH梯度分布也不一致；板状胶比柱状胶pH值分布宽、蛋白质谱带多、分辨率高；板状胶酸性端只有1—2cm没有蛋白带、蛋白带分布比较均匀且压得比较紧．这说明在用子宫内膜作为实验材料进行电泳时用板状胶进行电泳的结果较好．     

碳氮结构空心管材料及其对钍离子的吸附性能研究

目的合成碳氮结构空心管材料,用于稀土矿山开采中放射性钍离子的吸附去除,方法通过三聚氰胺和三聚氰酸超分子自组装,经水热碳化及高温热解,制备碳氮结构空心管材料.采用SEM、XRD等对材料进行表征.在不同热解温度和pH值下进行钍离子吸附实验,比较不同钍离子的初始浓度和吸附时间下吸附容量的差异.结果600℃时,材料形貌为均匀的中空管状结构;pH=3.5,热解温度为800℃时,材料最大吸附容量达到133.87 mg/g,吸附过程符合Langmuir等温吸附模型且遵从准二级动力学规律.结论碳氮结构空心管材料对钍离子具有良好的吸附效果,有望用于稀土开采过程中产生的放射性废钍离子的去除.     

天然气引射调峰系统的噪声形成及其治理研究

采用天然气引射调峰技术,能使上海某储配站10台天然气高压球罐的储气调峰能率提高68%,大大有助于解决天然气用气高峰时的供需平衡问题,并能节约初投资人民币1亿元.但使用超音速引射器后,当球罐压力下降到某一值时会产生高频噪声,影响管束区操作环境.本文分析了噪声产生的原因,提出了合理的噪声治理方案,并进行了方案的实施.实践证明:噪声治理效果良好,降低了管束区噪声污染,达到了国家"工业企业噪声卫生标准".     

Risk and characteristics analysis of the flow-induced vibration of the dip tube in opposed multi-burner gasifier

The vibration of dip tube in multi-burner gasifier changes the stress at the connection, causing flange seal failures and high temperature gas erosions with heavy economic losses and industrial accidents. This work aims to reveal the dip tube vibration mechanism, with special focus on obtaining the effect of operational parameters on the fatigue damage and long-term stable operation of gasifiers. A three-dimensional numerical simulation of the water-scrubbing cooling chamber was conducted to obtain the excitation source in the flow field. Then a FSI (fluid-structure interaction) transient dynamics simulation was carried out to investigate the vibration characteristics. Two major flow forms were found: a vertical annular flow near the dip tube outlet in the water-scrubbing cooling chamber; and a gas-liquid coupled flow caused by the syngas entrained the liquid. These two unstable multiphase flow forms exerted an energy excitation on the dip tube, resulting in a self-excited flutter. The dip tube vibration was similar to the first mode of a cantilever beam. The peak frequency was less affected by the initial liquid level and the syngas stream inlet velocity, which was close to its own first natural frequency. Note that, the alternating load generated by vibration may cause fatigue damage, which needs to be specifically considered in the design and manufacturing process of opposed multi-burner gasifier.     

组合钢管混凝土式防屈曲支撑

由于河北省图书馆加固改造工程的实际需要,开发出了一种新型组合钢管混凝土式防屈曲支撑。该新型支撑解决了全钢型防屈曲支撑在大长度时难以满足稳定性的问题,而且比起传统钢管混凝土约束的防屈曲支撑,无需考虑内芯与混凝土之间的粘结力问题,加工过程简便、施工速度快,且质量容易控制。现已对此类新型支撑完成了短试件和足尺试件的拟静力滞回性能试验,试验结果表明,新型支撑的滞回曲线饱满稳定,整体稳定性和局部稳定性较好,满足工程要求。     

煤层瓦斯含量测定定点取样方法研究进展

基于文献调研及前期研究,分析了目前煤矿井下煤层瓦斯含量直接测定时所采用定点取样方法及其弊端,阐述了学者们提出的改进型定点取样方法,并对煤层瓦斯含量测定定点取样方法的研究进行了展望,指出:①取样过程瓦斯损失量小、取样时升温低、机械复杂度低是基于煤芯管法定点取样方法的发展方向;②开展煤储层条件下的瓦斯运移规律研究,建立并完善各种基于煤芯管法的定点取样方法的瓦斯损失量模型;③适用于松软煤层的定点取样方法的研发亟待开展;④基于负压气力输送理论的定点取样方法是定点取样方法研究的趋势,动态颗粒煤变负压瓦斯解吸规律是建立对应瓦斯损失量模型的基础研究。     

油池火作用下钢管混凝土柱温度分布研究

在开敞空间条件下利用油池火模拟不同的火灾场景,对火源燃烧阶段和燃烧结束后钢管混凝土柱的温度变化进行研究。测量了燃料质量变化和钢管混凝土柱的温度分布等参数,分析不同火灾场景下钢管混凝土柱轴向、横截面的温度变化,并以实验工况HS3为例进行深入分析,同时分析了火源的燃烧时间、热释放速率对钢管混凝土柱温度场分布的影响。研究结果表明,钢管混凝土柱纵向温度分布与横向温度分布一样都存在明显的温度梯度,其表面钢管温度变化受火场热释放速率影响较大,而内部混凝土的温度变化则主要受火场持续时间的影响。     

陶瓷纤维滤管在烟气净化一体化技术中的应用

在对国内外现有的一体化烟气处理工艺系统梳理的基础上,重点分析了基于陶瓷纤维滤管的烟气净化一体化技术,对其技术原理、应用特性、应用现状进行了分析总结,并以江苏某垃圾焚烧发电厂中试示范项目为例进行验证.结果表明,NOx、SO2、HCl、颗粒物、二噁英类去除效率分别为97.6％、84.1％、74.8％、>99.9％、99.9...     

弯管与盲通管冲蚀磨损对比分析研究

为了研究石油管道流向急剧改变处的冲蚀磨损问题,采用DPM模型,通过改变入口流速、颗粒质量流速、颗粒直径,对90°弯管与盲通管的流场分布及冲蚀情况进行数值模拟。结果表明:弯管与盲通管最大冲蚀速率随入口流速的增大呈指数增长,随颗粒质量流速的增大呈线性增长;在50~100 μm粒径范围内,最大冲蚀速率随粒径的增加逐渐减小,在100~300 μm粒径范围内,随粒径的增加而增大;在入口流速、颗粒质量流速、颗粒直径相同的条件下,弯管最大冲蚀速率明显高于盲通管最大冲蚀速率,盲通管的耐蚀性更强;由于流体在盲通管产生涡旋现象,增加了颗粒能量的耗散,从而减小了进入下游管线颗粒的速率,使得颗粒更易积存于盲通段形成堆积层,减小了下游管段冲蚀速率。     

Small-scale physical explosions in shock tubes in comparison with condensed high explosive detonations

A series of small-scale experiments involving physical explosions in a 1.6 l pressure vessel was carried out. Explosions were initiated by spontaneous rupture of an aluminium membrane on one side of the vessel at a pressure in the range 1–1.2 MPa. The pressure waves released were measured at different distances along two separate shock tubes, one 10 m long and 200 mm in diameter (closed at one end by the high pressure vessel) and the other 15 m long and 100 mm in diameter.TNT equivalency was used for predicting the blast wave characteristics after vessel rupture. TNT equivalency was used because equations for prediction of peak pressure and impulse of the blast wave in 1-D geometry after detonations of condensed explosives are known. Some experiments with an equivalent amount of real explosive were carried out for comparison with the theoretical and experimental data obtained. The applicability of the TNT equivalency method presented for calculations of maximum pressure and shock wave impulse generated after rupture of the pressure vessel in 1-D geometry is discussed.