机械化学法修复柴油污染土壤的效率、产物及影响

针对常规污染土壤修复处理方法存在有毒降解产物、容易产生二次污染等问题,本研究采用行星球磨仪研究了机械化学法（MC）对柴油污染土壤的修复效能,利用GC/MS对柴油烃组分的降解产物进行分析,并采用SEM、XRD、BET、FTIR和TGA等方法对不同处理条件下的土壤样品进行表征.结果表明,MC处理在0.5~4.0 h内对土壤中总石油烃（TPH）的去除率可达95%以上.随着初始TPH浓度和球土质量比的升高,TPH去除率随之提高.采用MC处理后柴油组分降解难度顺序如下：烷烃<烯烃<环烷烃<芳香族化合物.在球磨处理4 h后,未检出有毒有害残留物质.球磨后土壤粒径变小,表面变粗糙,粘土矿物中的硅氧四面体暴露在土壤表面,矿物结构的结晶度逐渐降低,晶体结构逐渐破裂或变形,可在土壤表面形成富电子区域或促使土壤具有更高的反应活性,这是机械化学法高效降解柴油的主要机制.其次,土壤有机质的主要官能团受到破坏,纳米级孔隙容量降低,从而降低了土壤组分的吸附能力,增加了柴油的有效性,也有助于柴油的解吸和机械化学降解.此外,随着球磨时间的增加,土壤有机碳（SOC）含量先增加后下降,但均高于处理前.可见,MC处理可以快速彻底降解土壤中的柴油,且有利于增加土壤有机碳含量,对于石油烃污染土壤修复具有较好的应用潜力.     

机械化学法对含氯有机物的脱氯研究进展

评述了机械化学法脱氯的影响因素、反应机制、机械能与脱氯反应转化率的理论分析和脱氯研究中的分析方法.影响机械化学法脱氯效果的重要影响因素为机械能、脱氯剂、脱氯剂与处理物的混合比.脱氯反应中.主要存在脱氯形成自由基以及氢化和聚合反应两种反应路径.机械能与含氯有机物的分解率呈线性关系.     

荧光灯管芯柱玻璃中金属铅的机械化学硫化

以硫化钠为硫化剂,机械化学硫化荧光灯管芯柱玻璃中金属铅,实现金属铅向硫化铅快速转化.通过单因素实验,考察了不同机械化学硫化条件,即球磨时间、球磨转速和球料比对硫化率的影响,并通过XRD、SEM和粒度对硫化产物进行表征.结果表明,硫化率随球磨时间和球磨转速的增大而增大,随球料比的增大先增大后减小,当球磨转速为750r/min、球磨时间为120min、球料比为50：1g/g时,荧光灯管芯柱玻璃中金属铅的硫化率可达96.18%.XRD结果表明,荧光灯管芯柱玻璃中金属铅的机械化学硫化产物为PbS、SEM和粒度结果表明,荧光灯管芯柱玻璃的粒径随球磨转速和球磨时间的增加而减小.     

机械化学法降解2,4,6-三氯苯酚

以金属氧化物为磨料,在常温常压,行星式球磨机转速500r/min条件下,通过机械化学法降解2,4,6-三氯苯酚(TCP)。用气相色谱测定产物中剩余TCP含量,电位滴定法测定各反应阶段产物中游离氯离子含量,X射线衍射仪检测各金属氧化物磨料的晶粒尺寸和形状。结果表明磨料对TCP的摩尔配比越大,TCP降解率越高,当MgO与TCP摩尔配比为80:1时,TCP降解率达98.36%;6h后游离氯离子含量占投料TCP中总氯含量的76%,有>2/3的有机氯已转化为无机氯;不同磨料中,碱土金属氧化物对TCP降解效果较好。     

High-recycled-content hydraulic cements of alternative chemistry for concrete production

Sustainable hydraulic cements based on alkali aluminosilicate chemistry were developed with market-limited wastes acting as the primary aluminosilicate precursors. Two sets of formulations were developed with waste brick or impounded coal ash used at relatively large volume as aluminosilicate precursors. Supplementary materials were used to produce raw materials of viable chemistry. Blends of raw materials were transformed into hydraulic cements by input of mechanical energy without resorting to elevated temperatures. The resultant hydraulic cements exhibited viable strength development characteristics. FTIR, SEM, EDS and NMR analyses were conducted in order to gain insight into the structure of the hydraulic cements and their hydration products. The results pointed at the prevalence of calcium aluminosilicate hydrates among the products of hydration which thoroughly bound the non-hydrated cores of cement particles.     

机械力化学活化HPW-TiO_2/膨润土光催化降解甲基橙

采用溶胶-凝胶法制备了磷钨酸(HPW)改性TiO_2,并固载于膨润土上,再经机械力化学活化,得到机械力化学活化HPW-TiO_2/膨润土(MCA-HPW-TiO_2/膨润土)复合光催化剂。采用XRD,SEM,EDS技术对复合光催化剂进行了表征,并将其用于甲基橙的紫外光催化降解。表征结果显示:活性组分TiO_2和HPW成功固载于膨润土上;在机械力化学活化作用下,膨润土层间结构遭到破坏,TiO_2的XRD特征峰形呈弥散状态。实验结果表明:机械力化学活化作用对HPW-TiO_2/膨润土的光催化性能提升效果显著;在酸性及近中性条件下MCA-HPWTiO_2/膨润土均具有较高的催化活性;在溶液p H 6.2、初始甲基橙质量浓度10 mg/L、反应时间180 min、MCAHPW-TiO_2/膨润土投加量1 g/L的条件下,甲基橙去除率达88.27%;该光催化降解过程符合一级动力学模型。     

高浓度DDTs污染土壤机械化学球磨试剂筛选

为了筛选DDTs(包括DDT及其衍生物——DDE、DDD)高污染土壤无害化处理的机械化学球磨试剂,以某退役DDT生产场地高污染土壤为研究对象,将不添加任何球磨试剂处理作为对照,分析添加不同球磨主剂(CaO、CaO₂和Fe粉)、球磨助剂(SiO₂、Al₂O₃)组合以及双金属(Fe-Ni、Fe-Zn)试剂对土壤中DDTs的去除效果. 结果表明:①对照处理下土壤w(DDTs)随球磨时间的延长而不断降低,8 h后降至404.0 mg/kg,仍远超过GB 5085.6—2007《危险废物鉴别标准 毒性物质含量鉴别》标准限值〔w(DDTs)为50 mg/kg〕;单一添加CaO₂处理球磨8 h后,土壤及球磨剂混合物中w(DDTs)仍为118.0 mg/kg;而单一添加CaO和Fe粉处理分别于球磨4和6 h后,土壤及球磨剂混合物中w(DDTs)低于GB 5085.6—2007标准,因此,CaO和Fe粉是较好的DDTs机械化学球磨主剂. ②与单一添加CaO处理相比,在CaO中加入球磨助剂SiO₂或Al₂O₃球磨4 h后,土壤及球磨剂混合物中 w(DDTs)由28.55 mg/kg分别显著降至18.70或17.57 mg/kg,DDTs去除率由99.16%升至99.45%或99.48%. 与单一添加Fe粉处理相比,在Fe粉中加入SiO₂或Al₂O₃球磨4 h后,土壤及球磨剂混合物中w(DDTs)由193.0 mg/kg分别显著降至54.25或69.98 mg/kg,虽然仍略超过GB 5085.6—2007标准限值,但却显示出SiO₂或Al₂O₃对机械化学去除土壤DDTs具有显著的促进作用. ③Fe-Ni和Fe-Zn双金属球磨处理4 h后,土壤及球磨剂混合物中w(DDTs)分别为27.00和4.00 mg/kg,DDTs去除率分别达到99.21%和99.88%. 因此,Fe-Zn双金属作为去除土壤DDTs的机械化学球磨试剂,具有潜在的应用前景.      

Characterization of mechanochemical treated fly ash from a medical waste incinerator

The mechanochemical treatment of fly ash generated from a medical waste incinerator was subjected to grinding for 2 hr at 400 r/min in a planetary ball mill. The treated fly ash was characterized by a suite of analytical methods including High Resolution Gas Chromatograph/High Resolution Mass Spectrometer, Mastersizer 2000 Particle Size Analyzer, QUADRASORBTM SI Surface Area Analyzer, Scanning Electron Microscopy and X-ray di raction. Results showed that abatement e ciency of polychlorinated dibenzop- dioxins and polychlorinated dibenzofurans (PCDDs/Fs) in terms of total concentration averagely amount to 76% which was relatively higher than that of I-TEQ concentration averagely amount to 56%; the most concentration of toxic congeners as well as isomers of PCDDs/Fs decreased after mechanochemical treatment. The treated fly ash was characterized by a more homogeneous distribution of concaves as well as the significant decreasing in overall particle size and great enlargement in surface area. The major crystallization phases or intensities were considerably changed by mechanochemical treatment, of which a new phase containing chlorine formed may be a possible factor suggesting chlorination reaction occurring on the crystalline surface.     

Mechanochemical decomposition of pentachlorophenol by ball milling

The mechanochemical dechlorination of pentachlorophenol (PCP) was studied using CaO and SiO2 powder as additives. The e ects of the milling time and additives on the dechlorination rate were investigated. The resulting product was characterized by X-ray di raction (XRD), Fourier transform infrared spectra (FT-IR), thermogravimetric analysis (TG) and ion chromatography (IC). It is found that grinding operation could dechlorinate PCP, with the formation of inorganic chloride and amorphous carbon. The addition of quartz to the grinding mixture facilitated dechlorination. On the basis of the experimental results, the decomposition mechanism was proposed. Decomposition predominantly proceeds through rupture of C–Cl bond in PCP molecule, followed by the formation of inorganic chlorides.     

锌粉对聚氯乙烯的机械化学还原脱氯

以锌粉为还原剂进行了聚氯乙烯（PVC）的机械化学还原脱氯（简称脱氯）探索研究,考察了球磨转速、球料比（磨球与试样的质量比）、锌粉与PVC质量比等对脱氯率的影响,并对脱氯产物进行了X射线衍射、红外光谱等分析。实验结果表明,最佳工艺条件为球料比33、球磨转速528r／min、锌粉与PVC质量比9;产物中未形成结晶性氯化锌,且锌粉被氧化成ZnO;行星球磨比搅拌球磨对PVC的脱氯效果好,球磨时间超过3h,PVC的脱氯率可接近100％。