不同生物载体模拟河道反应器的微污染水源水修复研究

分别以弹性填料和AquaMats生态基为载体,比较了2组模拟河道生物反应器启动过程及其修复微污染水源水性能.结果表明,在间歇曝气与逐步增强曝气强度的挂膜启动方式下,悬挂弹性填料的模拟河道反应器运行50d即启动完成,其高锰酸盐指数、氨氮去除率分别高达78.2%、93.5%;AquaMats生态基反应器的高锰酸盐指数、氨氮去除率则在2周后分别达到70%、80%以上.不同曝气方式的影响研究发现,曝气/停曝时间比3h:3h、曝气量250L·h-1工况下,弹性填料生物膜反应器的高锰酸盐指数、氨氮、TN、TP的去除率均优于AquaMats反应器;随着曝气强度减至120L·h-1及曝气/停曝时间比缩短,AquaMats反应器的污染物去除性能逐步提高,表明其在确保一定的污染物去除率的前提下具有低气水比潜力与节能降耗的应用优势.镜检分析发现,弹性填料表面以颗粒物质截留、丝状菌包裹为主,而AquaMats生态基上附着的生物膜微生物群落相对较丰富.研究认为,呈辐射状结构的弹性填料对颗粒态污染物具有较强的截留能力,可实现微污染源水修复系统快速挂膜与稳定运行;而AquaMats生态基内部微孔结构有利于不同功能的微生物富集,可在低气水比条件下强化多种低浓度污染物的协同去除.     

垃圾渗滤液的膜生物反应器与传统生物工艺述评

采用文献调研法比较评价了膜生物反应器与传统生物工艺对垃圾渗滤液的处理效果。结果表明,渗滤液的水质特征(主要指COD)主要由渗滤液年龄决定,B/C值和渗滤液年龄对COD去除有重要影响。传统生物处理常采用多级组合工艺,渗滤液特性、工艺单元数、水力停留时间和有机负荷率等是影响COD去除的重要参数。近年来,MBR工艺的应用日益广泛,对于B/C值较低的老龄渗滤液,MBR工艺可获得更好的COD去除效果,也有利于废水的膜深度处理。     

内循环(IC)反应器运行规律研究

研究采用自制内循环(IC)反应器,以实验室模拟废水为进水,接种城市污水处理厂的剩余污泥,对反应器的启动及运行过程进行研究,在经过污泥驯化、颗粒培养、调整及稳定的不同阶段连续运行.结果表明:启动初期反应器pH过低,产甲烷菌生长受抑制,导致VFA累积,容易酸化.通过改变模拟废水中微量元素的浓度及添加缓冲溶液,酸化的反应器可...     

COD/SO42-对硫酸盐有机废水处理效率的影响

以人工配制的含硫酸盐有机废水作为原水,研究不同COD/SO42-值下厌氧折流板反应器(ABR)处理含硫酸盐有机废水去除率.试验结果表明:当COD/SO42-＜14.8时COD的去除率可达95%,SO42-的去除率在86%～96%之间;当COD/SO42-在14.8～4.0之间时,COD的去除率有所下降但仍能保持在94%...     

高压脉冲电凝-Fenton-生化法处理制药废水

通过高压脉冲电凝-Fenton对制药废水进行预处理,出水进入UASB-AO生化处理系统.研究表明:高压脉冲电凝-Fenton氧化法的最佳工况条件为进水pH值为4.0左右,高压脉冲电凝反应时间为45 min,H2O2投加量为4mL/L,Fenton氧化时间为60min.高压脉冲电凝-Fenton对CODCr去除率为36.5%～39.2%,ρ(BOD5)/ρ(CODCr)从0.13提高到0.32-0.34,废水的可生化性大大提高,UASB厌氧反应器去除率为81.4%～82.1%,AO系统去除率为88.0%～88.5%,而整个生化处理系统对CODCr去除率为95.4%～97.9%,最终出水各项指标可达到GB 8978-1996<污水综合排放标准>中一级标准.     

废旧线路板中主要有价金属的生物反应器浸出研究

为探讨可供实际生物浸出应用的反应器规模废旧线路板中有价金属浸出特性和工艺条件,通过设计序批式生物浸出反应器,采用分离到的氧化亚铁硫杆菌Z1作为菌种资源,在考察废旧线路板中有价金属的浸出特性的基础上,确定了反应器运行的最佳工艺条件.结果表明,反应器运行的最佳工艺条件为曝气量1L/min、停留时间30h、搅拌速率300r/min以及粉末投加量12g/L.在此条件下,经过101h可以浸出90.24%的铜.同时,经197h的浸出,可以溶出93.06%的镁、92.00%的锌、85.59%的铝和64.51%的镍.因此,生物浸出反应器能有效回收废旧线路板中的有价金属,为该技术的实际应用提供了实验证据.     

曝气强度对膜生物反应器处理石化废水工艺运行特征的影响

采用膜生物反应器(Membrane Bioreactor,MBR)处理石化废水,研究曝气强度分别为1.50,3.00 m3/(m2·h)的条件下,MBR对石化废水中主要污染物的去除特征、跨膜压差(Trans Membrane Pressure,TMP)和混合液性质的变化特征。结果表明:在两种曝气强度条件下MBR对COD、NH+4-N及挥发酚等污染物的平均去除率分别为80.74%、80.23%、96.79%和97.55%、99.34%、98.84%,即在不同曝气条件下,曝气强度的变化对MBR的污染物去除性能无显著影响。但随着曝气强度由1.50 m3/(m2·h)增加到3.00 m3/(m2·h),MBR达到设定的最大跨膜压差(TMPMax=25k Pa)的运行时间由11.8 d增加到31.4 d,TMP上升速率降低。通过活性污泥颗粒粒径分析发现:增加曝气强度后,对膜污染影响显著的活性污泥颗粒粒径范围(0~2μm)所占体积比由2.10%减小到1.78%;并且混合液中溶解性微生物产物(soluble microbial product,SMP)和胞外聚合物(extracellular polymeric substance,EPS)质量浓度分别由24.07 mg/L和15.66 mg/g减小到15.14 mg/L和9.81 mg/g,从而降低了膜污染速率。     

Enhanced struvite recovery from wastewater using a novel cone-inserted fluidized bed reactor

The feasibility of struvite recovery at low （12.5 mg/L） and high （120 mg[L） phosphorus concentrations was studied by constructing a novel fluidized bed reactor with cones （FBRwc） and without cones （FBRwoc）. The crystallization process was continuously operated for 133 days under different hydraulic retention times （HRT = 1-10 hr）, pH （7.5-10）, and molar ratios of Mg/P （0.75-1.75）, N/P （1-10） and Ca/Mg （0-2）. The optimum operating conditions of HRT, pH, Mg/P and N/P molar ratios were found to be 2 hr, 9, 1.25, and 7.5, respectively. Under these optimum conditions, the phosphorus precipitation efficiencies of FBRwc were 93% for low and 98% for high phosphorus influent; however, the efficiencies were 78% and 81% for FBRwoc, respectively. Due to crystal losses at each junction （17%-31%）, the crystal recovery efficiency of FBRwoc was relatively low （47%-65%） for both influent concentrations. However, the losses were minimal in FBRwc, which showed 75% and 92% crystal recovery for low and high phosphorus concentrations, respectively. At low calcium concentration, crystal chemical analysis showed the product to be pure struvite （〉 99%）. The scanning electron microscope and X-ray diffraction results further confirmed that the crystal recovered from FBRwc contained pure struvite, which could be considered a high quality fertilizer. Except HRT, all parameters （pH, Mg/P, N/P and Ca/Mg） were found to be influencing factors for FBRwc performance. Overall, inserting cones in each part of the reactor played a significant role in enhancing struvite recovery from a wide range of phosphorus-containing wastewater.     

MBR出水后置化学除磷研究

选用不同的化学除磷药剂及固液分离方式,针对膜生物反应器出水进行后置化学除磷静态试验研究。试验表明,在MBR出水平均浓度为(6.0±0.3)mg/L时,在化学药剂的最佳投药量和混凝时间的条件下,TP可以稳定达到一级A标准,去除率达到95%以上;滤液达一级A标准,氯化铝、氯化铁、聚合硫酸铁、硫酸铝最佳投加量为1.5 mol/mol,硫酸铁、聚合硫酸铝最佳投加量为3.0 mol/mol,最佳混凝时间均为10 min;滤纸和滤膜可以有效分离混凝混合液中的TP,滤液TP可稳定达一级A标准,而微网对混合液中粒径小于D10的颗粒无法分离,致使滤液TP无法达标;PAM投加后,絮体粒径显著增大,固液分离效果也相应增强。微网分离效果较投加前有了明显提高,滤液TP可稳定达到一级B标准。     

Aerobic granules cultivated and operated in continuous-flow bioreactor under particle-size selective pressure

A novel method based on the selective pressure of particle size （particle-size cultivation method, PSCM） was developed for the cultivation and operation of aerobic granular sludge in a continuous-flow reactor, and compared with the conventional method based on the selective pressure of settling velocity （settling-velocity cultivation method, SVCM）. Results indicated that aerobic granules could be cultivated in continuous operation mode by this developed method within 14 days. Although in the granulation process, under particle-size selective pressure, mixed liquor suspended solids （MLSS） in the reactor fluctuated greatly and filamentous bacteria dominated the sludge system during the initial operation days, no obvious difference in profile was found between the aerobic granules cultivated by PSCM and SVCM. Moreover, aerobic granules cultivated by PSCM presented larger diameter, lower water content and higher specific rates of nitrification, denitrifieation and phosphorus removal, but lower settling velocity. Under long term operation of more than 30 days, aerobic granules in the continuous-flow reactor could remain stable and obtain good chemical oxygen demand （COD）, NH4^＋-N, total nitrogen （TN） and total phosphorus （TP） removal. The results indicate that PSCM was dependent on the cultivation and maintenance of the stability of aerobic granules in continuous-flow bioreactors.