催化剂Ru/ZrO2-CeO2催化湿式氧化苯酚

催化剂Ru/ZrO₂-CeO₂催化湿式氧化苯酚的过程表明,Ru/ZrO₂-CeO₂可以显著提高COD和苯酚去除效果,当反应温度为170℃,压力为3 MPa,反应120 min后,COD和苯酚的去除率分别达到了99％和100％.试验还考察了不同反应条件对苯酚溶液COD去除的影响,并获得了最优的反应条件：温度为170℃,压力为3 MPa,催化剂的投加量为5　g/Ｌ,搅拌速度为500 r/min.通过对中间产物的分析,本研究提出了催化湿式氧化苯酚的简单路径图,认为苯酚首先被氧化成小分子有机酸,接着小分子有机酸被氧化成二氧化碳和水.前一个过程是快速反应,后一个过程中的乙酸氧化是慢速过程,需要在高温下才能完成.乙酸的氧化主要是自由基攻击α碳上的C—H键,先生成甲酸,并最终生成二氧化碳和水.     

Effect of platinum on the photocatalytic degradation of chlorinated organic compound

TiO2 nanoparticles, doped with di erent Pt contents, were prepared by a modified photodeposition method using Degussa P-25 TiO2, H2PtCl6 6H2O and methanol as the solvents. The physicochemical properties of Pt/TiO2 were investigated by the nitrogen adsorption and desorption isotherm measurement technique, X-ray di raction analysis and photoluminescence spectra, respectively. Reaction rates from photocatalytic removal of dichloromethane over Degussa P-25 TiO2 and Pt/TiO2 were evaluated. The average diameter and BET surface area of the TiO2 catalyst particles were 300 nm and 50 m2/g, respectively. The degradation e ciency was 99.0%, 82.7%, 55.2%, and 57.9% with TiO2 at inlet concentrations of 50, 100, 200, and 300 ppm, respectively. And the degradation e ciency was 99.3%, 79.7%, 76.5%, and 73.4% with a 0.005 wt.% Pt/TiO2 at inlet concentrations of 50, 100, 200, and 300 ppm, respectively. In addition, we found that the photoluminescence emission peak intensities decreased with increases in the doping amount of Pt, which indicates that the irradiative recombination was weakened. Furthermore, the results showed that the UV/0.005 wt.% Pt/TiO2 process was capable of e ciently decomposing gaseous DCM in air.     

中心组合设计优化S-Cr-TiO2催化剂光降解工艺条件

在确定的温度和光照条件下,采用中心组合设计法研究了固相反应法合成的硫与铬共掺杂二氧化钛(S-Cr-TiO2)光催化剂与水溶苯胺蓝(ANB)可见光降解过程中的三个作用因子:催化剂的浓度、水溶苯胺蓝水溶液的pH值及其初始浓度之间的相互作用关系,得到了影响因子与降解速率之间的回归方程及因素之间相互作用的响应面图.结果表明,S...     

吸附树脂负载铁酞菁催化降解硝基苯的研究

在可见光照射下,采用吸附树脂负载铁酞菁催化过氧化氢降解硝基苯.考察了光照、催化剂投加量、双氧水投加量、温度及pH值等因素对催化效果的影响.结果表明,在功率为50W卤钨灯照射下,硝基苯溶液初始质量浓度为200 mg/L,初始pH值为3,催化剂投加量为1.5 g/L,双氧水投加量为1.0 mL/L,温度为35℃下反应10h,硝基苯去除率可达到79.9％.     

Reaction mechanism and metal ion transformation in photocatalytic ozonation of phenol and oxalic acid with Ag+/TiO2

Photocatalytic ozonation of phenol and oxalic acid （OA） was conducted with a Ag^＋/TiO2 catalyst and different pathways were found for the degradation of different compounds. Ag^＋ greatly promoted the photocatalytic degradation of contaminants due to its role as an electron scavenger. It also accelerated the removal rate of OA in ozonation and the simultaneous process for its complex reaction with oxalate. Phenol could be degraded both in direct ozonation and photolysis, but the TOC removal rates were much higher in the simultaneous processes due to the oxidation of hydroxyl radicals resulting from synergetic effects. The sequence of photo-illumination and ozone exposure in the combined process showed quite different effects in phenol degradation and TOC removal. The synergetic effects in different combined processes were found to be highly related to the properties of the target pollutants. The color change of the solution and TEM result confirmed that Ag＋ was easily reduced and deposited on the surface of Tit2 under photo-illumination, and dissolved again into solution in the presence of ozone. This simple cycle of enrichment and distribution of Ag^＋ can greatly benefit the design of advanced oxidation processes, in which the sequences of ozone and photo-illumination can be varied according to the needs for catalyst recycling and the different properties of pollutants.     

Effects of metal and acidic sites on the reaction by-products of butyl acetate oxidation over palladium-based catalysts

Catalytic oxidation is widely used in pollution control technology to remove volatile organic compounds. In this study, Pd/ZSM-5 catalysts with different Pd contents and acidic sites were prepared via the impregnation method. All the catalysts were characterized by means of N2 adsorption- desorption, X-ray fluorescence （XRF）, HE temperature programmed reduction （H2-TPR）, and NH3 temperature programmed desorption （NH3-TPD）. Their catalytic performance was investigated in the oxidation of butyl acetate experiments. The by-products of the reaction were collected in thermal desorption tubes and identified by gas chromatography/mass spectrometry. It was found that the increase of Pd content slightly changed the catalytic activity of butyl acetate oxidation according to the yield of CO2 achieved at 90%, but decreased the cracking by-products, whereas the enhancement of strong acidity over Pd-based catalysts enriched the by-product species. The butyl acetate oxidation process involves a series of reaction steps including protolysis, dehydrogenation, dehydration, cracking, and isomerization. Generally, butyl acetate was cracked to acetic acid and 2- methylpropene and the latter was an intermediate of the other by-products, and the oxidation routes of typical by-products were proposed. Trace amounts of 3-methylpentane, hexane, 2-methylpentane, pentane, and 2-methylbutane originated from iso4merization and protolysis reactions.     

Experimental study on filtration and continuous regeneration of a particulate filter system for heavy-duty diesel engines

This study investigated the filtration and continuous regeneration of a particulate filter system on an engine test bench, consisting of a diesel oxidation catalyst（DOC） and a catalyzed diesel particulate filter（CDPF）. Both the DOC and the CDPF led to a high conversion of NO to NO2 for continuous regeneration. The filtration efficiency on solid particle number（SPN） was close to100%. The post-CDPF particles were mainly in accumulation mode. The downstream SPN was sensitively influenced by the variation of the soot loading. This phenomenon provides a method for determining the balance point temperature by measuring the trend of SPN concentration.     

Unregulated emissions from diesel engine with particulate filter using Fe-based fuel borne catalyst

The alteration and formation of toxic compounds and potential changes in the toxicity of emissions when using after-treatment technologies have gained wide attention. Volatile organic compound（VOC）, carbonyl compound and particle-phase polycyclic aromatic hydrocarbon（PAH） emissions were tested at European Steady State Cycle（ESC） to study unregulated emissions from a diesel engine with a fuel-borne catalyst and diesel particulate filter（FBC–DPF）. An Fe-based fuel-borne catalyst was used for this study. According to the results, brake specific emissions of total VOCs without and with DPF were 4.7 and4.9 mg/kWh, respectively, showing a 4.3% increase. Benzene and n-undecane emissions increased and toluene emission decreased, while other individual VOC emissions basically had no change. When retrofitted with the FBC–DPF, total carbonyl compound emission decreased 15.7%, from 25.8 to 21.8 mg/kWh. The two highest carbonyls, formaldehyde and acetaldehyde, were reduced from 20.0 and 3.7 to 16.5 and 3.3 mg/kWh respectively. The specific reactivity（SR） with DPF was reduced from 6.68 to 6.64 mg/kWh. Total particle-phase PAH emissions decreased 66.4% with DPF compared to that without DPF. However, the Benzo[a]pyrene equivalent（BaPeq） with DPF had increased from 0.016 to 0.030 mg/kWh.Fluoranthene and Pyrene had the greatest decrease, 91.1% and 88.4% respectively. The increase of two- and three-ring PAHs with DPF indicates that the fuel-borne catalyst caused some gas-phase PAHs to adsorb on particles. The results of this study expand the knowledge of the effects of using a particulate filter and a Fe-based fuel-borne catalyst on diesel engine unregulated emissions.     

Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

Photocatalytic activity of Fe-doped CaTiO3 under UV-visible light

The photocatalytic degradation of methylene blue（MB） over Fe-doped CaTiO3 under UV-visible light was investigated. The as-prepared samples were characterized using X-ray diffraction（XRD）, scanning electron microscope（SEM） equipped with an energy dispersive spectrometer（EDS） system, Fourier transform infrared spectra（FT-IR）, and UV-visible diffuse reflectance spectroscopy（DRS）. The results show that the doping with Fe significantly promoted the light absorption ability of CaTiO3 in the visible light region. The Fe-doped CaTiO3 exhibited higher photocatalytic activity than CaTiO3 for the degradation of MB.However, the photocatalytic activity of the Fe-doped CaTiO3 was greatly influenced by the calcination temperature during the preparation process. The Fe-doped CaTiO3 prepared at500°C exhibited the best photocatalytic activity, with degradation of almost 100% MB（10 ppm）under UV-visible light for 180 min.