连续流动氢化物发生原子荧光法测定水中硒

文章介绍连续流动一氢化物发生一原子荧光测定水中硒的方法,研究了盐酸浓度、硼氢化钾浓度、灯电流、光电倍增管负高压、泵速、载气和屏蔽气流量等对测定硒的影响,找出测定水中硒最佳条件,在最佳条件下,校准曲线相关系数为0.9999.方法检出限为0.0095μg/L,方法的测量范围为0.038-300μg/L,回收率在91.8%-...     

聚丙烯中空纤维膜吸收法烟气脱硫实验研究

采用质量分数为30%的甲基二乙醇胺(MDEA)水溶液为烟气SO2吸收液,聚丙烯(PP)中空纤维微孔膜组件为吸收器,研究吸收液温度、流量变化,气体停留时间,以及气液两相流程等操作条件对聚丙烯(PP)中宅纤维膜脱硫率的影响,研究表明30%MDEA水溶液在温度35℃,流量100mL/min的最佳试验条件下,经过一个膜吸收过程...     

模拟环境条件下δ-MnO_2氧化As(Ⅲ)的搅拌流动动力学特征

采用搅拌流动法研究了酸性水钠锰矿及水羟锰矿2种δ-MnO2矿物氧化As(Ⅲ)的动力学过程,构建了可用于多相体系的搅拌-流动氧化还原反应动力学模型.经过As吸附量的校正后,该模型对酸性水钠锰矿及水羟锰矿氧化As(Ⅲ)动力学数据拟合度分别为0.980和0.951,模型拟合得到pH 7时2种矿物单位比表面上氧化As(Ⅲ)的初始反应速率常数k分别为0.131,0.014min-1·m-2.相比而言,该速率常数明显高于批量法得到的表观速率常数kobs,0.021,0.001min-1?m-2更接近真实的化学动力学参数.搅拌流动法与批量法得到的不同矿物的速率常数大小趋势一致,即尽管酸性水钠锰矿对As(Ⅲ)的氧化率低于水羟锰矿,单位比表面上酸性水钠锰矿氧化As(Ⅲ)初始反应速率却远高于水羟锰矿.反应过程分析表明,反应初始阶段,As(Ⅲ)的吸附为主要限速步骤;而随着反应的进行,矿物表面反应位点逐渐钝化或减少,反应位点数量成为限速步骤.     

Catalytic bubble-free hydrogenation reduction of azo dye by porous membranes loaded with palladium nanoparticles

Catalytic bubble-free hydrogenation reduction of azo dye by porous membranes loaded with palladium （Pd） nanoparticles was studied for the first time. The effects of Pd loading, dye concentration and reuse repetitions of membranes were investigated. In reduction, the dye concentration decreased whereas the pH rose gradually. An optimal Pd loading was found. The catalytic membranes were able to be reused more than 3 times.     

曝气强度对膜生物反应器处理石化废水工艺运行特征的影响

采用膜生物反应器(Membrane Bioreactor,MBR)处理石化废水,研究曝气强度分别为1.50,3.00 m3/(m2·h)的条件下,MBR对石化废水中主要污染物的去除特征、跨膜压差(Trans Membrane Pressure,TMP)和混合液性质的变化特征。结果表明:在两种曝气强度条件下MBR对COD、NH+4-N及挥发酚等污染物的平均去除率分别为80.74%、80.23%、96.79%和97.55%、99.34%、98.84%,即在不同曝气条件下,曝气强度的变化对MBR的污染物去除性能无显著影响。但随着曝气强度由1.50 m3/(m2·h)增加到3.00 m3/(m2·h),MBR达到设定的最大跨膜压差(TMPMax=25k Pa)的运行时间由11.8 d增加到31.4 d,TMP上升速率降低。通过活性污泥颗粒粒径分析发现:增加曝气强度后,对膜污染影响显著的活性污泥颗粒粒径范围(0~2μm)所占体积比由2.10%减小到1.78%;并且混合液中溶解性微生物产物(soluble microbial product,SMP)和胞外聚合物(extracellular polymeric substance,EPS)质量浓度分别由24.07 mg/L和15.66 mg/g减小到15.14 mg/L和9.81 mg/g,从而降低了膜污染速率。     

Inhibitory effects of nisin-coated multi-walled carbon nanotube sheet on biofilm formation from Bacillus anthracis spores

Multi-walled carbon nanotube（MWCNT） sheet was fabricated from a drawable MWCNT forest and then deposited on poly（methyl methacrylate） film. The film was further coated with a natural antimicrobial peptide nisin. We studied the effects of nisin coating on the attachment of Bacillus anthracis spores, the germination of attached spores, and the subsequent biofilm formation from attached spores. It was found that the strong adsorptivity and the super hydrophobicity of MWCNTs provided an ideal platform for nisin coating. Nisin coating on MWCNT sheets decreased surface hydrophobicity, reduced spore attachment, and reduced the germination of attached spores by 3.5 fold, and further inhibited the subsequent biofilm formation by 94.6% compared to that on uncoated MWCNT sheet. Nisin also changed the morphology of vegetative cells in the formed biofilm.The results of this study demonstrated that the anti-adhesion and antimicrobial effect of nisin in combination with the physical properties of carbon nanotubes had the potential in producing effective anti-biofilm formation surfaces.     

Fouling distribution in forward osmosis membrane process

Fouling behavior along the length of membrane module was systematically investigated by performing simple modeling and lab-scale experiments of forward osmosis （FO） membrane process. The flux distribution model developed in this study showed a good agreement with experimental results, validating the robustness of the model. This model demonstrated, as expected, that the permeate flux decreased along the membrane channel due to decreasing osmotic pressure differential across the FO membrane. A series of fouling experiments were conducted under the draw and feed solutions at various recoveries simulated by the model. The simulated fouling experiments revealed that higher organic （alginate） fouling and thus more flux decline were observed at the last section of a membrane channel, as foulants in feed solution became more concentrated. Furthermore, the water flux in FO process declined more severely as the recovery increased due to more foulants transported to membrane surface with elevated solute concentrations at higher recovery, which created favorable solution environments for organic adsorption. The fouling reversibility also decreased at the last section of the membrane channel, suggesting that fouling distribution on FO membrane along the module should be carefully examined to improve overall cleaning efficiency. Lastly, it was found that such fouling distribution observed with co-current flow operation became less pronounced in counter- current flow operation of FO membrane process.     

Aerobic granules cultivated and operated in continuous-flow bioreactor under particle-size selective pressure

A novel method based on the selective pressure of particle size （particle-size cultivation method, PSCM） was developed for the cultivation and operation of aerobic granular sludge in a continuous-flow reactor, and compared with the conventional method based on the selective pressure of settling velocity （settling-velocity cultivation method, SVCM）. Results indicated that aerobic granules could be cultivated in continuous operation mode by this developed method within 14 days. Although in the granulation process, under particle-size selective pressure, mixed liquor suspended solids （MLSS） in the reactor fluctuated greatly and filamentous bacteria dominated the sludge system during the initial operation days, no obvious difference in profile was found between the aerobic granules cultivated by PSCM and SVCM. Moreover, aerobic granules cultivated by PSCM presented larger diameter, lower water content and higher specific rates of nitrification, denitrifieation and phosphorus removal, but lower settling velocity. Under long term operation of more than 30 days, aerobic granules in the continuous-flow reactor could remain stable and obtain good chemical oxygen demand （COD）, NH4^＋-N, total nitrogen （TN） and total phosphorus （TP） removal. The results indicate that PSCM was dependent on the cultivation and maintenance of the stability of aerobic granules in continuous-flow bioreactors.     

日本膜技术的发展与产业化及其借鉴意义

对日本膜技术发展历史及现状进行了系统梳理。研究表明,经过数十年持续不断的投入,日本膜技术已广泛应用在净水处理、生活污水处理、工业废水处理及脱盐等领域,并在国际市场占据重要地位。虽然受本土市场规模的局限,超滤微滤膜在日本给水处理领域的处理规模仅为1.3×106m3d,反渗透膜脱盐能力为1.44×106m3d,但日本的超滤微滤膜在全球给排水领域的应用约为1.0×107m3d,反渗透膜产品在全球的应用超过3.0×107m3d。建议我国膜企业应借鉴日本膜产业的发展经验,加大膜企业的研发投入,加强膜技术的研发创新能力,通过提供更高性价比的产品和卓越的技术服务开拓国际市场。     

膜曝气生物反应器处理模拟啤酒废水的研究

以聚偏氟乙烯中空纤维膜构建无泡曝气膜生物反应器(MABR)处理模拟啤酒废水,在保持进水COD∶TN∶TP=100∶5∶1条件下,通过正交实验确定反应器的最佳运行条件,并在此条件下考察了反应器对啤酒废水中COD、氨氮和总磷的去除能力。研究表明,反应器对啤酒废水中的COD、氨氮有着良好的去除效果,系统稳定时COD与氨氮的平均去除率分别为88.6%和92.4%,此外MABR工艺具有较强的抗有机负荷冲击能力。但反应器对总磷的去除效果不够理想,平均去除率在30%左右。