不锈钢壳体的冷挤压工艺及模具设计

壳体是机械中广泛使用的重要零件之一.采用冷挤压工艺可提高质量、降低成本.对不锈钢壳体成形工艺及模具设计作了详细讨论.     

Removal of high concentrated ammonia nitrogen from landfill leachate by landfilled waste layer

The landfill of municipal solid waste(MSW) could be regarded as denitrification reactor and involved in ammonia nitrogen biological removal process. In this research, the process was applied to municipal solid waste collected in Shanghai, China, which was characterized by high food waste content. The NH4^ removal efficiency in the system of SBR nitrifying reactor followed by fresh and matured landfilled waste layer in series was studied. In the nitrifying reactor, above 90% of NH4^ in leachate was oxidized to NO2^- and NO3^- . Then high concentrated NO2^- and NO3^- were removed in the way of denitrification process in fresh landfilled waste layer. At the same time, degradation of fresh landfilled waste was accelerated. Up to the day 120, 136.5 gC/(kg dry waste) and 17.9 gN/(kg dry waste) were converted from waste layer. It accounted for 50.15 % and 86.89 % of the total carbon and nitrogen content of preliminary fresh waste, which was 4.42 times and 5.17 times higher than that of reference column respectively. After filtering through matured landfilled waste, BOD5 concentration in leachate dropped to below 100 mg/L, which would not affect following nitrification adversely. Because the matured landfilled waste acted as a well methanogenic reactor, 23% of carbon produced accumulatively from fresh landfilled waste degradation was converted into CH4.     

BOD微生物膜的再利用研究初探

对失去大部分活性的微生物膜进行再培养,以研究膜再利用的可能性。试验结果初部表明:在1/2MS培养基中加入一定量的植物激素,不仅可以使膜的电位值(I0)显著升高,且活性强,稳定性好,可使膜重复利用。     

从染料厂有机废液中蒸馏回收二氯苯的研究

采用常压蒸馏和减压蒸馏的方法对酸性染料厂有机废液中的高浓度二氯苯进行回收,并通过气相色谱-质谱联用仪对回收的二氯苯进行定性和定量分析以确定回收率．结果表明,常压蒸馏和减压蒸馏均能有效地回收废液中的二氯苯,常压蒸馏的回收率约88％,减压蒸馏具有相对较好的回收效果,回收率约94％。两种蒸馏方法的选择需要在经济分析的基础上进行确定。     

微生物絮凝剂的研究方法和进展

通过分析目前国内外微生物絮凝的研究现状，归纳了微生物絮凝剂的一般研究方法，综述了微生物絮凝剂的研究成果，提出了微生物絮凝剂研究中亟待解决的问题和建议。     

翻管工艺及其模具

此文介绍了一种新的金属成形工艺——翻管工艺,它是将管坯翻转成双层管、多层管或其他形状的管制件。概述了翻转管在航空、航天、机动车辆、石油化工、机械电子等领域的应用情况。分析了翻管工艺变形过程及其变形特征,介绍了几种翻管模具,如锥形模、圆角模、槽形模、拉伸翻管模的结构、原理及其设计方法。通过金属塑性成形理论,导出了在上述模具上翻管的一些重要工艺参数,如临界锥角、圆角模半径、稳定翻管力等。也分析了翻管工艺过程中出现的管坯失稳的影响因素,提出了翻转和失稳之间的相互转化形式、防止失稳产生的一些工艺措施。此文的结果可作为翻管工艺分析和模具设计的依据。     

煤矿生产污水处理工艺设备的试验研究

本文针对煤矿生活污水的水质特性，提出了用活性污泥法和新型组合式一元化净水器相结合处理煤矿生活污水的新工艺。     

高浓度印染废水处理工程工艺条件与实例分析

研究以三相生物流化床作为工程化反应器处理印染废水的工程工艺条件及操作特性，分别测定流化床内的气相含率，兴体循环速度及体积氧传质系数。     

Quantitative structure - activity study on the reductivedehalogenation potency of the halogenated aromatics

Ｑｕａｎｔｉｔａｔｉｖｅｓｔｒｕｃｔｕｒｅ－ａｃｔｉｖｉｔｙｓｔｕｄｙｏｎｔｈｅｒｅｄｕｃｔｉｖｅｄｅｈａｌｏｇｅｎａｔｉｏｎｐｏｔｅｎｃｙｏｆｔｈｅｈａｌｏｇｅｎａｔｅｄａｒｏｍａｔｉｃｓＨｕａｎｇＱｉｎｇｇｕｏ；ＷａｎｇＬｉａｎｓｈｅｎｇ；Ｈａｎ...     

金属铁还原降解2,4-二硝基甲苯的实验研究

研究了金属铁对2,4-二硝基甲苯(2,4-DNT)的还原降解情况.实验结果表明,2,4-DNT的还原降解与溶液初始pH值、初始浓度和溶解氧等因素有关.氯离子能消除金属铁的钝化现象.金属铁表面附载的铜对2,4-DNT的还原降解具有催化作用.