纳滤膜过滤MBR出水的污染原因与清洗方法

为研究膜-生物反应器(MBR)出水对纳滤膜的污染原因及清洗方法,使用场发射扫描电镜、傅立叶变换红外光谱仪、原子力显微镜和接触角仪对经MBR出水污染的纳滤膜表面污染层进行了检测,结果表明,纳滤膜表面污染物包括有机物和无机物,所含元素包括磷、镁等,对经过不同清洗步骤的膜表面进行的检测表明,柠檬酸清洗可以去除镁和大部分磷,这些物质主要以无机形态存在于膜面污染物中;后续NaOH清洗可以进一步去除磷,这部分磷主要来自有机酸、有机磷或蛋白质等膜面污染物.污染使膜表面粗糙度由79.5 nm增大至111.2 nm,但接触角由55.6°变为62.1°,表明亲水性变化不大;酸洗后表面粗糙度显著减小至51.9 nm,接触角变为96.0°,表明有机污染物暴露出来,膜面呈现疏水性;再经碱洗后,膜面粗糙度与亲水性均接近于新膜.这些结果说明,先酸洗后碱洗的方法可以去除绝大部分的膜面污染物,进一步推知膜污染初期主要为有机污染,之后无机物的作用使污染进一步加重.     

沉积物中重金属铅的释放动力学模拟

采用扩散通量模型(DIFS)模拟了沉积物中Pb从固相向液相释放的动力学过程.模拟结果表明,对于扩散梯度膜(DGT)测定的Pb浓度CDGT与孔隙水Pb浓度比值(R)接近1的S1样品,靠近DGT的液相Pb被消耗后,固相吸附态Pb迅速补给消耗;其解吸速率常数k-1较大,而且非稳态Pb含量较大,在放置时间(t)内,DGT表面孔隙水Pb浓度一直维持在初始浓度.而对于R接近0的S2样品(无补给情况),靠近DGT孔隙水Pb被消耗后,固相的补给很少,反映在相关参数上便是非稳态Pb含量较低,而且解吸速率常数k-1很小,DGT表面处孔隙水Pb浓度随放置时间的增加而降低.对于R值等于0.39的S3样品(部分补给情况),非稳态Pb含量和解吸速率常数k-1介于S1和S2样品之间,固相的补给能力介于S1和S2之间.由以上模拟结果可知,沉积物中重金属释放动力学过程受到非稳态Pb含量和释放动力学参数共同影响.     

O_3-MBR法深度处理煤气废水

以经多级生物处理后的煤气废水为原水,采用O3-MBR组合工艺对其进行深度处理,以满足回用要求.结果表明:采用臭氧氧化工艺,当废水pH为11和臭氧投加量〔ρ(臭氧)〕为189.2mg/L时,CODCr和色度的去除率分别为46.5%和80.2%,ρ(BOD5)/ρ(CODCr)由0.02升至0.29,废水的可生化性得到明显改善;臭氧氧化工艺出水再通过MBR作进一步处理,CODCr,NH3-N和色度的去除率分别达23.0%,76.3%和70.0%,且出水水质稳定;总体上,废水经O3-MBR组合工艺处理,CODCr,NH3-N,色度和浊度的平均总去除率分别达到58.7%,76.3%,88.6%和95.1%;处理后出水的ρ(CODCr)50mg/L,ρ(NH3-N)5mg/L,浊度0.2NTU,色度约为30度,出水水质满足生产工艺回用的要求.     

臭氧对膜法水处理中膜污染的影响

膜过滤是一种高效水处理技术,包括污水处理中的膜-生物反应器（membrane bioreactor,MBR）和针对二级生物处理出水（生产再生水）、地表水（生产饮用水）的膜过滤工艺等,其中膜污染是制约膜工艺应用的一个主要问题.臭氧具有强氧化性,在水处理上得到了广泛的应用.近十几年来,针对臭氧-膜过滤组合工艺的研究正变得越来越多,因此本文对这些研究进行了系统综述与分析.在MBR组合臭氧控制膜污染方面的研究中,目前结论相对较少.可以通过对MBR进水预臭氧化或者投加适量臭氧到MBR混合液这2种方式来减轻MBR膜污染.在针对微污染水的臭氧-膜过滤组合工艺中,根据臭氧的功能和结构形式主要分为3种,分别是污染膜臭氧清洗、分离式臭氧-膜工艺和一体式臭氧-膜工艺.绝大部分报道认为臭氧可以有效地控制膜污染的发展,但也有少数投加臭氧后膜污染加剧的情况.目前,臭氧化影响膜污染机制的研究主要集中在有机物方面,根据原水水质和工艺结构参数等的不同,颗粒物、微生物和无机物质也在这个过程中起着相应的作用.另外,在迄今为止的研究中,还缺乏对于臭氧投加方式和分散方式的统一衡量和比较标准.作者建议应该加强对一体式臭氧-膜组合工艺的研究,并且要注意臭氧投加的工艺经济性.     

An innovative membrane bioreactor and packed-bed biofilm reactor combined system for shortcut nitrification-denitrification

An innovative shortcut biological nitrogen removal system, consisting of an aerobic submerged membrane bioreactor (MBR) and an anaerobic packed-bed biofilm reactor (PBBR), was evaluated for treating high strength ammonium-bearing wastewater. The system was seeded with enriched ammonia-oxidizing bacteria (AOB) and operated without sludge purge with a decreased hydraulic retention time (HRT) through three phases. The MBR was successful in both maintaining nitrite ratio over 0.95 and nitrification efficiency higher than 98% at a HRT of 24 h. The PBBR showed satisfactory denitrification efficiency with very low effluent nitrite and nitrate concentration (both below 3 mg/L). By examining the nitrification activity of microorganism, it was found that the specific ammonium oxidization rate (SAOR) increased from 0.17 to 0.51 g N/(g VSS·d) and then decreased to 0.22 g N/(g VSS·d) at the last phase, which resulted from the accumulation of extracellular polymers substances (EPS) and inert matters enwrapped around the zoogloea. In contrast, the average specific nitrite oxidization rate (SNOR) is 0.002 g N/(g VSS·d), only 1% of SAOR. Because very little Nitrobactor has been detected by fluorescence in situ hybridization (FISH), it is confirmed that the stability of high nitrite accumulation in MBR is caused by a large amount of AOB.     

Performance of microbiological control by a point-of-use filter system for drinking water purification

Purification capacity of a faucet mounted type water filter for home use was evaluated, particularly with regard to microbiological performance under di erent running conditions. Biofilms were formed inside the filter, a ecting the bacterial quality of the e uent water. Low flow rate, long stagnation period and high filter temperature were found favorable for bacterial growth inside. By commercial analytical profile index (API) kits, ten di erent bacterial species were identified in drinking water, four of which were probably contributed to the biofilm formation since they were also present in the biofilm. Fluorescence in situ hybridization (FISH) was used to confirm the API identification results, and direct viable count (DVC) method was employed to improve the sensitivity of FISH for the isolated Acinetobacter spp. and Pseudomonas putida as models. Relationship between the filter operating condition and the bacterial community alteration was partly revealed, which could provide the basic knowledge for the filter design and its practical use.     

内压式中空纤维超滤膜污染模型研究

以流体力学和过滤理论为基础,建立了一个描述内压式中空纤维超滤膜污染的数学模型。该模型将膜的性质、原水的性质、清洗条件等多种因素对超滤过程的影响,用一个参数——膜堵塞系数表示。实验以造纸黒液稀释水为原水,对模型参数进行了拟合、验证,模拟计算结果与实验实测数据比较吻合,说明该模型能较好的模拟内压式中空纤维超滤膜过滤过程。     

一体式膜生物反应器处理生活污水的研究

研究了一体式膜生物反应器对生活污水的处理效果。实验结果表明,膜生物反应器对COD、TOC、NH4+-N、TN、TP的平均去除率为93.4%、96.2%、97.2%、63.8%、60.6%,并且污泥活性随着运行时间的延长而有所降低。     

pH值调节对红霉素膜浆中抗生素的降解作用

利用微生物法对红霉素膜浆中的红霉素药物残留量进行测定,红霉素残留量为265．88μg／mL。再通过调节pH值不同对膜浆残留红霉素的降解进一步研究。利用盐酸将膜浆的pH值调到2时,残留红霉素浓度为15．03μg／mL;降解率为94．35％。     

纤维乙醇黑液处理

采用微电解＋厌氧折流板反应器（ABR）＋上流式厌氧污泥床（UASB）＋膜生物反应器（MBR）组合工艺对纤维乙醇黑液进行处理。结果表明：当黑液中COD质量浓度在12000mg／L左右,该组合工艺中厌氧停留时间（HRT）为48h时,厌氧COD去除率达到72％,MBR中的HRT为20h时,COD的去除率在80．8％～87．5％之间,出水COD质量浓度稳定在301～537mg／L．且MBR抗冲击负荷能力较强。