Particle fluxes above forests: observations, methodological considerations and method comparisons

This paper reports a study designed to test, evaluate and compare micro-meteorological methods for determining the particle number flux above forest canopies. Half-hour average particle number fluxes above a representative broad-leaved forest in Denmark derived using eddy covariance range from -7x10(7) m(-2) s(-1) (1st percentile) to 5x10(7) m(-2) s(-1) (99th percentile), and have a median value of -1.6x10(6) m(-2) s(-1). The statistical uncertainties associated with the particle number flux estimates are larger than those for momentum fluxes and imply that in this data set approximately half of the particle number fluxes are not statistically different to zero. Particle number fluxes from relaxed eddy accumulation (REA) and eddy covariance are highly correlated and of almost identical magnitude. Flux estimates from the co-spectral and dissipation methods are also correlated with those from eddy covariance but exhibit higher absolute magnitude of fluxes.     

Comparison of Microscopic and Macroscopic Modeling Approaches for Subsurface Contaminant Transport

The practice of contaminant transport and remediation has shown significant progress in recent years. However, despite the significant progress made, remediation efforts are often delayed by extremely long breakthrough curve tails that render efforts to bring the level of contaminants below the regulatory standards inefficient. One hypothesis is that these long tails are due to the reservoir-like slow diffusive processes in soil micropore zones. This study compares the effects of micropores at macroscopic and microscopic levels and establishes a link between these approaches for validation and calibration purposes. The link between macroscopic and microscopic levels is established through comparisons and testing of the two models while incorporating appropriate scale and boundary effects. Despite the differences in conceptual approaches and simulation time, the two approaches rendered meaningful results. The link helps forecast the effects of micropore zone transport processes in the subsurface efficiently and thus allows development of numerical tools that could contribute towards more efficient remediation design.     

PSO和SVM混合算法确定太湖入湖河流水质主要影响因子

以影响太湖入湖河流水质的24个因子值为研究对象,将PSO算法与SVM算法相结合。PSO算法用于优化SVM算法的参数c和g,以利于快速、高效地确定c和g的全局最优值;SVM算法基于最优的c和g,分别以24,21,18,15,12,9和6个因子作为特征向量预测水质的污染程度。结果表明,当特征向量为9个影响因子时预测率最高。其参数c=18.56,g=1.35,对应的预测率为：全局预测率92.59%,重度污染水质预测率88.89%,轻度污染水质预测率94.45%。因此,通过PSO和SVM混合算法,可以确定影响太湖入湖河流水质的主要因子,利用这些主要因子对水质进行预测预警,不但可以节省时间,而且可以得到精确的结果。     

燃煤电厂在线监测系统颗粒物浓度排放系数影响因素的探讨

选取上海市7家未安装气-气换热器的国控燃煤电厂作为研究对象,从煤质、除尘器、脱硫协同脱除作用以及锅炉工况负荷等方面探讨对颗粒物浓度排放系数 K值产生的影响,得出上述因素通过改变脱硫进口颗粒物浓度值影响 K值,当脱硫进口颗粒物浓度较低、波动范围较小时,其 K值也维持相对稳定的状态;当脱硫进口颗粒物浓度较高、波动范围较大时,其 K值也会发生较大的变化等结论。     

基于韦伯-费希纳定律的空气质量普适韦伯指数公式

在适当设定各项空气污染物浓度"参照值"cj0的基础上,用相应于"参照值"cj0的污染物的"规范值"xj作为基于韦伯-费希纳(W-F)定律空气质量指数公式中的污染刺激量。由于各污染物同级标准的浓度"规范值"xjl差异不大,从而可以认为各污染物的韦伯指数公式等效于一个具有共同适用的韦伯常数α的W-F指数公式,并采用粒子群(PSO)算法优化得出α,得到对7项空气污染物皆适用的空气质量普适韦伯指数公式。该公式应用于多个实例分析,并与多种其它评价方法的评价结果比较表明,空气质量普适韦伯指数公式具有简单、实用和直观的特点。     

A Two-Stage Particle Swarm Optimization Algorithm for MPPT of Partially Shaded PV Arrays

The power-voltage (P-V) characteristic curves of a PV array are nonlinear and have multiple peaks under partially shaded conditions (PSCs). This paper proposes a novel maximum power point tracking (MPPT) method for a PV system with reduced steady-state oscillation based on a two-stage particle swarm optimization (PSO) algorithm. The grouping method of the shuffled frog leaping algorithm (SFLA) is incorporated in the basic PSO algorithm (PSO-SFLA), ensuring fast and accurate searching of the global extremum. An adaptive speed factor is also introduced into the improved PSO to further enhance its convergence speed. Test results show that the proposed method converges in less than half the time taken by the conventional PSO method, and the power is improved by 33% under the worst PSCs, which confirms the superiority of the proposed method over the standard PSO algorithm in terms of tracking speed and steady-state oscillations under different PSCs.     

Determination of specific gravity of municipal solid waste

This investigation was conducted to evaluate experimental determination of specific gravity (G_s) of municipal solid waste (MSW). Water pycnometry, typically used for testing soils was adapted for testing MSW using a large flask with 2000 mL capacity and specimens with 100–350 g masses. Tests were conducted on manufactured waste samples prepared using US waste constituent components; fresh wastes obtained prior and subsequent to compaction at an MSW landfill; and wastes obtained from various depths at the same landfill. Factors that influence specific gravity were investigated including waste particle size, compaction, and combined decomposition and stress history. The measured average specific gravities were 1.377 and 1.530 for as-prepared/uncompacted and compacted manufactured wastes, respectively; 1.072 and 1.258 for uncompacted and compacted fresh wastes, respectively; and 2.201 for old wastes. The average organic content and degree of decomposition were 77.2% and 0%, respectively for fresh wastes and 22.8% and 88.3%, respectively for old wastes. The G_s increased with decreasing particle size, compaction, and increasing waste age. For fresh wastes, reductions in particle size and compaction caused occluded intraparticle pores to be exposed and waste particles to be deformed resulting in increases in specific gravity. For old wastes, the high G_s resulted from loss of biodegradable components that have low G_s as well as potential access to previously occluded pores and deformation of particles due to both degradation processes and applied mechanical stresses. The G_s was correlated to the degree of decomposition with a linear relationship. Unlike soils, the G_s for MSW was not unique, but varied in a landfill environment due both to physical/mechanical processes and biochemical processes. Specific gravity testing is recommended to be conducted not only using representative waste composition, but also using representative compaction, stress, and degradation states.     

Effects of low concentration biodiesel blend application on modern passenger cars. Part 1: Feedstock impact on regulated pollutants, fuel consumption and particle emissions

Five biodiesels from different feedstocks (rapeseed, soy, sunflower, palm, and used fried oils) blended with diesel at 10% vol. ratio (B10), were tested on a Euro 3 common-rail passenger car. Limited effects (−2% to +4%) were observed on CO₂ emissions. CO and HC emissions increased between 10% and 25% on average, except at high speed - high power where emissions were too low to draw conclusions. NOx emissions increased by up to 20% for two out of the five blends, decreased by up to 15% for two other blends, and remained unchanged for one blend. Particulate matter (PM) was reduced for all blends by up to 25% and the reductions were positively correlated with the extent of biodiesel saturation. PM reductions are associated with consistent reductions in non-volatile particle number. A variable behaviour in particle number is observed when volatile particles are also accounted.     

Potential effects of particulate matter from combustion during services on human health and on works of art in medieval churches in Cyprus

Indoor and outdoor particulate matter (PM_0.3-10) number concentrations were established in two medieval churches in Cyprus. In both churches incense was burnt occasionally during Mass. The highest indoor PM_0.5-1 concentrations compared with outdoors (10.7 times higher) were observed in the church that burning of candles indoors was allowed. Peak indoor black carbon concentration was 6.8 μg m⁻³ in the instances that incense was burning and 13.4 μg m⁻³ in the instances that the candles were burning (outdoor levels ranged between 0.6 and 1.3 μg m⁻³). From the water soluble inorganic components determined in PM₁₀, calcium prevailed in all samples indoors or outdoors, whilst high potassium concentration indoors were a clear marker of combustion. Indoor sources of PM were clearly identified and their emission strengths were estimated via modeling of the results. Indoor estimated PM_0.3-10 mass concentrations exceeded air quality standards for human health protection and for the preservation of works of art.     

Accumulation and quantitative estimates of airborne lead for a wild plant (Aster subulatus)

Foliar uptake of airborne lead is one of the pathways for Pb accumulation in plant organs. However, the approximate contributions of airborne Pb to plant organs are still unclear. In the present study, aerosols (nine-stage size-segregated aerosols and total suspended particulates), a wild plant species (Aster subulatus) and the corresponding soils were collected and Pb contents and isotopic ratios in these samples were analyzed. Average concentration of Pb was 96.5 ± 63.5 ng m⁻³ in total suspended particulates (TSP) and 20.4 ± 5.5 ng m⁻³ in the fine fractions of size-segregated aerosols (SSA) (<2.1 μm), higher than that in the coarser fractions (>2.1 μm) (6.38 ± 3.71 ng m⁻³). Enrichment factors show that aerosols and soils suffered from anthropogenic inputs and the fine fractions of the size-segregated aerosols enriched more Pb than the coarse fractions. The order of Pb contents in A. subulatus was roots > leaves > stems. The linear relationship of Pb isotope ratios (²⁰⁶Pb/²⁰⁷Pb and ²⁰⁸Pb/²⁰⁶Pb) among soil, plant and aerosol samples were found. Based on the simple binary Pb isotopic model using the mean ²⁰⁶Pb/²⁰⁷Pb ratios in TSP and in SSA, the approximate contributions of airborne Pb into plant leaves were 72.2% and 65.1%, respectively, suggesting that airborne Pb is the most important source for the Pb accumulation in leaves. So the combination of Pb isotope tracing and the simple binary Pb isotope model can assess the contribution of airborne Pb into plant leaves and may be of interest for risk assessment of the exposure to airborne Pb contamination.