反应器引压端法兰焊接阀门断裂原因分析

通过对Z41H-160型阀体端法兰断裂件的宏观检查、化学成分分析、金相分析、断口形貌观察、EDS能谱分析和维氏硬度测试等研究,表明阀体热处理不当致使硬度超高,阀门结构不合理导致硫化物应力腐蚀是阀体断裂的主要原因。     

Vibrational energy loss analysis in battery tab ultrasonic welding

In ultrasonic metal welding processes, high-frequency ultrasonic energy is used to generate friction and heat at the interface between weld parts to produce solid-state bonds. It has been observed that sufficient energy is required to produce proper bonding, while excessive energy can cause such quality issues as weld fracture and perforation. Therefore, it is important to have a product/process design in ultrasonic welding to ensure efficient energy conversion from ultrasonics to welding energy, minimizing energy loss in the process. In this work, vibrational energy loss associated with the longitudinal and flexural vibrations of the Cu coupon during ultrasonic welding is studied by applying one-dimensional continuous vibration models. To facilitate our modeling, experimental results from the free response of Cu coupon were obtained to determine the damping characteristics of the Cu coupon in the welding process. Our analysis shows that substantial energy loss can occur during welding due to the flexural vibration of the Cu coupon, especially when the overhang (the upper part of the Cu coupon extended from the anvil) of the Cu coupon resonates at or close to the welding frequency (about 20 kHz), degrading the weld quality of battery tabs. This study contributes to understanding the fundamental dynamics of the Cu coupon during ultrasonic welding and its impact on weld quality.     

Microstructure of 2205 duplex stainless steel joint in submerged arc welding by post weld heat treatment

The 2205 duplex stainless steel (DSS) is of both good properties austenitic steel and ferritic steel, which applies to the shipbuilding industry usually. In this paper, the OM, XRD and microhardness test methods are used to analyze the variation of submerged arc welded (SAW) joints with and without post weld heat treatment (PWHT). The research results show that the σ phase disappear in the fusion edge zone near heat affect zone (HAZ) and an increase in the welded center zone during the follow-up PWHT, while the amount of γ phase is decreased in the welded center zone with PWHT. A segregation distribution of some second phases is also found in the welded center zone after PWHT. There have two pick values of microhardness arise in the fusion edge zone and the welded center zone separately without PWHT. However, a maximum value of microhardness at the fusion edge zone near HAZ is disappeared and the other is still held at the welded center zone during PWHT. It can be attributed to the changes of second phases, element diffusions and particle segregation during PWHT. A developing mechanism is issued to demonstrate the second phases transferring of the 2205 DSS SAW joints by PWHT.     

Improvement of welding heat source models for TIG-MIG hybrid welding process

Tungsten inert gas-metal inert gas (TIG-MIG) hybrid welding process is an effective way to improve welding productivity and quality due to advantages of the two processes. Mathematical analysis is crucial to fundamentally understand this synergetic welding process. In this study, based on experimental visualization of arc behaviors, some assumptions are proposed to deduce adaptive plane and volumetric heat source models separately for each involved welding method first. The influence of torch angles on distribution of temperature and geometry of weld bead are calculated and compared with experimental results. It shows that this developed algorithm of heat source can be employed to accurately predict welding process whether the electrode gun is slanted backward or forward to the direction of welding. Then TIG-MIG hybrid welding process is simulated and analyzed without considering the attractive or repulsive force of two arcs. The characteristic of TIG-MIG welding process is discussed compared to single MIG. It lays the foundation for the further research on the interaction of the two arcs during TIG-MIG hybrid welding.     

Development of chemically produced hydrogen energy-based impact bonding process for dissimilar metals

There has been a growing demand in the fabrication of dissimilar metal parts for application in the automotive, aerospace, defense, chemical and nuclear industries. Welding of dissimilar materials can be accomplished via impact welding, which can minimize the formation of a continuous inter-metallic phase, while chemically bonding dissimilar metals. This paper discusses an innovative technique for bonding dissimilar metals by chemically produced hydrogen energy by reacting aluminum powder and water. Experiments were carried out to study impact bond characteristics using copper and stainless steel cylindrical billets. The influence of nosed flyer billet angle and billet mass on bonding characteristics were studied. The test results have demonstrated that the nosed flyer billet angle has significant influence on wavy bond patterns at the interface. Among the three flyer billet nose angles of 9°, 12° and 15°, the billets with a flyer angle of 15° resulted in a complete wave morphological pattern along the whole sample cross-section. This study shows the potential of developing a cost effective system/machinery where discrete metal parts can be bonded at near net shape.     

Bitter coil design methodology for electromagnetic pulse metal processing techniques

Electromagnetic pulse metal processing techniques (EPMPT) such as welding, forming and cutting have proven to be an effective solution to specific manufacturing problems. A high pulse magnetic field coil is a critical part of these technologies and its design is a challenging task. This paper describes a Bitter coil design using a newly developed methodology for a simplified analytical calculation of the coil and complementary finite element models (FE) of different complexity. Based on the methodology a Belgian Welding Institute (BWI) Bitter coil has been designed and tested by means of short circuit experiments, impedance and B-field measurements. A good agreement between the calculated and the experimental design parameters was found.     

焊接车间烟尘特性及治理措施

焊接生产会产生烟尘,焊接烟尘给人体带来的危害是比较严重的,焊接烟尘的治理方法有多种,合理选用可使焊接生产变成绿色环保型作业.     

振弦栅收集电焊烟尘特性的数值模拟

为高效、低投入地处理电焊烟尘,得到过滤系统净化电焊烟尘的最佳设计参数,选择ICEM-CFD软件建立栅过滤系统的几何模型并进行网格划分,选用标准(Standard)k-ε模型、离散相模型(DPM),利用FLUENT软件对电焊烟尘过滤效率主要影响的单因素进行模拟计算。研究结论表明,用栅过滤系统过滤电焊烟尘颗粒时,振弦栅的栅丝直径、间距所决定填充率是过滤效率的直接决定因素;栅丝层间距是过滤效率的间接影响因素;通过探究振弦栅对电焊烟尘过滤效率的影响规律,进而为振弦栅的实际应用提供理论基础。     

一种高压油管焊接质量评价方法

阐述了高压油管疲劳破坏的原理及危害,建立高压油管焊接质量评价力学模型,通过有限元分析技术对其许用位移输入进行计算,并结合应变测量技术,利用电动振动台,对高压油管焊接处的疲劳特性进行了试验验证。结果表明,此高压油管焊接质量评价方法是可行的,有限元分析技术和应变测量技术的结合使用,保证了试验的安全性和结果准确性,此外,利用电动振动台进行疲劳耐久试验,操作方便简单,成本相对较低,具有通用性。     

Management Decentralization and Montane Forest Conditions in Tanzania

Abstract: We examined how differences in local forest‐management institutions relate to disparate anthropogenic forest disturbance and forest conditions among three neighboring montane forests in Tanzania under centralized, comanaged, or communal management. Institutional differences have been shaped by decentralization reforms. We conducted semistructured interviews with members of forest management committees, local government, and village households and measured anthropogenic disturbance, tree structure, and species composition in forest plots. We assessed differences in governance system components of local institutions, including land tenure, decision‐making autonomy by forest users, and official and de facto processes of rule formation, monitoring, and enforcement among the three management strategies. We also assessed differences in frequencies of prohibited logging and subsistence pole cutting, and measures of forest condition. An adjacent research forest served as an ecological reference for comparison of forest conditions. Governance was similar for comanaged and centralized management, whereas communal managers had greater tenure security and decision‐making autonomy over the use and management of their forest. There was significantly less illegal logging in the communal forest, but subsistence pole cutting was common across all management strategies. The comanaged forest was most disturbed by recent logging and pole cutting, as were peripheral areas of the larger centralized forest. This manifested in more degraded indicators of forest conditions (lower mean tree size, basal area, density of trees ≥ 90 cm dbh, and aboveground biomass and higher overall stem density). Greater tenure security and institutional autonomy of the communal strategy contributed to more effective management, less illegal logging, and maintenance of good forest conditions, but generating livelihood benefits was a challenge for both decentralized strategies. Our results underscore the importance of well‐designed institutional arrangements in forest management and illustrate mechanisms for improved forest governance and conservation in the context of Tanzanian decentralization reforms.