用GC/MS分析火灾后苯板产生固体废物中的有机物

采用GC/MS方法对某苯板厂火灾后产生的固体废弃物进行检测分析.结果表明,在苯板火灾后产生的固体废弃物中检测出61种化合物,其中被美国EPA列入优先污染物的苯系物、萘和蒽等占总有机物12.2％.     

稀释接种法测BOD5考核样品的一些注意点

用稀释接种法测定BOD5时,由于操作繁琐,全部实验时间需要5d,任一环节出现问题都会影响实验结果。在进行考核实验时,由于时间紧,样品量有限,因此每个实验操作步骤都要谨慎仔细。通过实践经验,就BOD,考核实验总结了一些注意点。     

膨胀石墨污水净化处理研究

利用膨胀石墨强大的吸附能力来处理城市生活污水,结果发现用膨胀石墨处理污水的前8h,COD的去除率达43％;处理第5～9d将出现第二个高峰,COD的去除率达48％,分析原因可能是存在物理吸附和微生物絮凝两方面的作用。最后经过20d的处理,膨胀石墨对生活污水的COD和BOD总去除率分别达到86％、78．9％,且除臭能力也很显著。     

环境管理过程中对锅炉型号的识别

通过对锅炉型号的简要介绍,提高对锅炉的认识,增强在污染源动态更新调查表的填报过程中锅炉技术指标的填报能力是十分必要的。     

FRP加固震损RC柱建模方法及骨架模型研究

为研究震损RC柱采用FRP(Fiber Reinforced Polymer,FRP)加固修复后的抗震性能,本文基于OpenSees仿真平台,根据震后RC柱的表观损伤状态提出FRP加固震损RC柱的有限元模型建立方法。对FRP加固震损RC柱进行5120种工况的Pushover分析,采用三折线荷载-位移骨架曲线,研究损伤状态对骨架曲线特征点参数的影响规律,并通过数据回归分析提出FRP加固震损RC柱的骨架曲线计算模型。分析结果表明:损伤会降低FRP加固RC柱的承载力及刚度,且降低程度随损伤指数的增大而增加,两者近似成抛物线关系;在DS-5损伤状态下,相比于FRP加固完好RC柱,FRP加固震损RC柱的屈服承载力P y、峰值承载力P c、弹性刚度K 1、弹塑性刚度K 2及下降段刚度K 3的均值下降17.9%、14.5%、41.8%、43.1%和19.9%;损伤对FRP加固RC柱弹性刚度和弹塑性刚度的降低程度明显高于屈服承载力和峰值承载力;文中提出的FRP加固震损RC柱骨架曲线计算模型具有较高精度。     

Effects of metal and acidic sites on the reaction by-products of butyl acetate oxidation over palladium-based catalysts

Catalytic oxidation is widely used in pollution control technology to remove volatile organic compounds. In this study, Pd/ZSM-5 catalysts with different Pd contents and acidic sites were prepared via the impregnation method. All the catalysts were characterized by means of N2 adsorption- desorption, X-ray fluorescence （XRF）, HE temperature programmed reduction （H2-TPR）, and NH3 temperature programmed desorption （NH3-TPD）. Their catalytic performance was investigated in the oxidation of butyl acetate experiments. The by-products of the reaction were collected in thermal desorption tubes and identified by gas chromatography/mass spectrometry. It was found that the increase of Pd content slightly changed the catalytic activity of butyl acetate oxidation according to the yield of CO2 achieved at 90%, but decreased the cracking by-products, whereas the enhancement of strong acidity over Pd-based catalysts enriched the by-product species. The butyl acetate oxidation process involves a series of reaction steps including protolysis, dehydrogenation, dehydration, cracking, and isomerization. Generally, butyl acetate was cracked to acetic acid and 2- methylpropene and the latter was an intermediate of the other by-products, and the oxidation routes of typical by-products were proposed. Trace amounts of 3-methylpentane, hexane, 2-methylpentane, pentane, and 2-methylbutane originated from iso4merization and protolysis reactions.     

Evaluation of accuracy of linear regression models in predicting urban stormwater discharge characteristics

Stormwater runoff has been identified as a source of pollution for the environment, especially for receiving waters. In order to quantify and manage the impacts of stormwater runoff on the environment, predictive models and mathematical models have been developed. Predictive tools such as regression models have been widely used to predict stormwater discharge characteristics. Storm event characteristics, such as antecedent dry days （ADD）, have been related to response variables, such as pollutant loads and concentrations. However it has been a controversial issue among many studies to consider ADD as an important variable in predicting stormwater discharge characteristics. In this study, we examined the accuracy of general linear regression models in predicting discharge characteristics of roadway runoff. A total of 17 storm events were monitored in two highway segments, located in Gwangju, Korea. Data from the monitoring were used to calibrate United States Environmental Protection Agency＇s Storm Water Management Model （SWMM）. The calibrated SWMM was simulated for 55 storm events, and the results of total suspended solid （TSS） discharge loads and event mean concentrations （EMC） were extracted. From these data, linear regression models were developed. R2 and p-values of the regression of ADD for both TSS loads and EMCs were investigated. Results showed that pollutant loads were better predicted than pollutant EMC in the multiple regression models. Regression may not provide the true effect of site-specific characteristics, due to uncertainty in the data.     

Pd/activated carbon sorbents for mid-temperature capture of mercury from coal-derived fuel gas

Higher concentrations of Hg can be emitted from coal pyrolysis or gasification than from coal combustion, especially elemental Hg. Highly efficient Hg removal technology from coal-derived fuel gas is thus of great importance. Based on the very excellent Hg removal ability of Pd and the high adsorption abilities of activated carbon（AC） for H2 S and Hg, a series of Pd/AC sorbents was prepared by using pore volume impregnation, and their performance in capturing Hg and H2 S from coal-derived fuel gas was investigated using a laboratory-scale fixed-bed reactor. The effects of loading amount, reaction temperature and reaction atmosphere on Hg removal from coal-derived fuel gas were studied. The sorbents were characterized by N2 adsorption, X-ray diffraction（XRD） and X-ray photoelectron spectroscopy（XPS）. The results indicated that the efficiency of Hg removal increased with the increasing of Pd loading amount, but the effective utilization rate of the active component Pd decreased significantly at the same time. High temperature had a negative influence on the Hg removal. The efficiency of Hg removal in the N2-H2S-H2-CO-Hg atmosphere（simulated coal gas） was higher than that in N2-H2S-Hg and N2-Hg atmospheres, which showed that H2 and CO, with their reducing capacity, could benefit promote the removal of Hg. The XPS results suggested that there were two different ways of capturing Hg over sorbents in N2-H2S-Hg and N2-Hg atmospheres.     

V2O5/TiO2催化剂脱除NO的研究

采用了等体积浸渍法制备二氧化钛负载钒氧化物催化剂（V2O5/TiO2）,研究了V2O5负载量、反应温度、烟气流量、氨氮比以及运行时间各因素对NH3选择性催化还原NO反应（SCR）效率的影响.研究结果表明：经过500℃温度下煅烧,烟气流量为200ml/min,负载量为7wt％的V2O5/TiO2催化剂,在400℃温度下反应,NO脱除率可达70.5％.     

浙江省污水污泥处理处置状况的调查

通过对丽水、宁波、衢州、诸暨等浙江省境内十几个地区的污水处理厂的调查发现:目前浙江省内的污水处理工艺中,A2/O、A/O、氧化沟三种工艺占了近50%的份额。而SBR因其方法特点正在受到越来越多的重视。在污泥处理工艺中,填埋占了最大的一部分,有近70%的污水处理厂将产生的污泥进行填埋处理。目前,污泥处理技术单一,需要继续探寻污泥的减量和资源化技术,为日益增多的污泥探寻出路。