Ti/SnO_2-Sb阳极-空气阴极电催化降解染料废水

为解决电化学法处理高盐染料废水存在的能耗大、成本高等问题,分别采用溶胶-凝胶法和辊压法制备Ti/SnO_2-Sb阳极和空气阴极,构建了Ti/SnO_2-Sb阳极-空气阴极双极体系(TSSA-ADC)。甲基橙(MO)作为高盐染料废水的典型污染物,考察了电流强度、MO浓度、电解液浓度和初始p H对TSSA-ADC体系和TSSA单阳极体系降解MO的影响。结果表明:与TSSA单阳极体系相比,TSSA-ADC体系具有更好的抗有机负荷冲击、抗盐分冲击、抗酸碱波动能力,能够维护酸碱平衡防止硬度离子结垢。最佳反应条件为电流强度为0.030 A,电解液浓度为3%,MO浓度为100 mg/L,初始pH=6。以MO去除率达到98%为基准,TSSA-ADC体系比TSSA体系可节能74.26%。     

城市大气中臭氧浓度控制的困难与挑战——以成都市为例

研究城市化、工业化和区域经济一体化进程的不断加快,对城市大气环境的影响是当前大气环境领域研究的热点问题。在此过程中,利用空气质量模型模拟系统研究大气环境污染问题成为大气环境研究中不可缺少的组成部分。在当前空气污染复杂的形势下,针对城市大气环境中臭氧的浓度尚未有效的控制措施。研究主要利用Models-3/CMAQ空气质量模式对成都市臭氧浓度数值通过不同的控制情景进行模拟,揭示城市大气中臭氧浓度控制的困难与挑战,并尝试性提出今后的研究方向,以期为控制城市大气中臭氧浓度提供建议。     

不同污水处理工艺N_2O减排方法研究进展

污水处理过程中产生强温室气体N_2O的问题已经受到广泛关注,如何在保证处理效率的同时实现N_2O有效减排成为水处理领域面临的重要问题。综述了传统生物脱氮除磷工艺和同步硝化反硝化、反硝化除磷、厌氧氨氧化等新型污水处理工艺运行过程中N_2O的产生机理、减排方法和减排量,为相关领域的研究人员提供参考。     

焙烧温度对CeO_2(ZrO_2)/TiO_2选择性催化脱硝性能的影响

采用溶胶-凝胶法并以不同温度焙烧制备一系列CeO_2(ZrO_2)/TiO_2(CZT)催化剂,考察了CZT催化剂固相结构、酸量、比表面积等性能与催化活性的关系。采用XRD、BET、NH3-TPD、H2-TPR以及XPS等表征技术对催化剂进行表征。结果表明:焙烧温度为450℃时CZT催化剂具有最高的催化活性,其在240~400℃的温度窗口内活性均高于90%,且具有较好的抗水和抗硫中毒能力。随着焙烧温度的提高,催化剂表面的Ce和Zr原子进入体相晶格且Ce0.5Zr0.5O2向Ce0.75Zr0.25O2转变,导致催化剂的储释氧能力和氧化还原性能降低。另外,锐钛矿和金红石型TiO_2晶粒尺寸的增加,催化剂的有效比表面积和总酸量降低,因此CZT催化活性随着焙烧温度的提高而有所降低。换言之,大的比表面积、良好的氧化还原性能、表面Ce4+的富集以及酸性位的增多均有利于NH3-SCR活性的提高。     

运用批实验研究溶解氧对米酒去除硝酸盐的影响

为了判别不同溶解氧条件下脱氮效果和碳的需求量,在水温为25~30℃条件下,设置了缺氧、微氧和有氧3种输入条件,以及C/N分别为2.0、1.5两种碳源投放量开展实验。研究表明:溶解氧的存在对反硝化作用的启动有延迟作用,但影响较小。溶解氧对于反硝化过程并没有产生明显的抑制作用,但在溶解氧较低的情况下,反硝化速率更为理想。缺氧条件下,C/N的适宜值应低于1.5;微氧条件下的C/N适宜值在1.5~2.0;而在有氧条件下C/N=2.0时可高效去除硝酸盐。该研究可为农村地区家庭自行去除饮用水中硝酸盐的实际应用提供参考。     

UV/H_2O_2对氯消毒副产物TCM、DCBM的去除影响因素研究

针对UV/H_2O_2对氯化消毒副产物三氯甲烷(TCM)和一溴二氯甲烷(DCBM)的去除效果及影响因素进行研究,结果表明UV/H_2O_2方法对TCM和DCBM去除效果的影响因素有过氧化氢(H_2O_2)投加量、紫外光照强度、反应p H值和反应物初始浓度。通过不同的反应条件得出:H_2O_2在一定投加量变化范围(10~35 mmol/L)内,随投加量的增加,TCM和DCBM的去除率均呈先上升后下降趋势,H_2O_2最佳投加量分别为25,20 mmol/L;增大紫外光照(UV)强度,TCM和DCBM的去除率均显著提高;随初始p H值的增大,去除率均呈先上升后下降趋势,p H值为7.0时,去除率达到最佳;TCM和DCBM反应初始浓度分别为150,160μg/L时,其去除率最高,在有效时间内去除率分别为95.88%、92.56%。     

Effect of MoO3 on vanadium based catalysts for the selective catalytic reduction of NOx with NH3 at low temperature

The selective catalytic reduction(SCR) activities of the MoO_3 doped V/WTi catalysts prepared by the incipient wetness impregnation method at low temperature were investigated.The results showed that the addition of MoO_3 could enhance the NO_ xconversion at low temperature and the best SCR activity was obtained when the dosage of MoO_3 reached5 wt.%. The NH3-TPD and DRIFTS experiments indicated that the addition of MoO_3 changed the type and number of acid sites on the surface of catalysts and reaction activities of acid sites were altered at the same time. The redox capacity and amount of active oxygen species got improved for V3Mo5/WTi catalyst, which could be confirmed by the H_2-TPR and transient response experiments. Water vapor inhibited the NO_xconversion at low temperature. Deposition of ammonium sulfate or bisulfate might be main reason for the loss of catalytic activity in the presence of SO_2 at low temperature. Choosing the suitable NH_3/NO ratio and elevation of reaction temperature both could weaken the influence of SO_2 on the SCR activity of the V3Mo5/WTi catalyst. Thermal treatment of the deactivated catalyst at350°C could get the low temperature activity recovered. The decrease of GHSV improved the de NO_x efficiency at low temperature and we speculated that the rational technological process and operation parameters could contribute to the application of this kind of catalysts in real industrial environment.     

In-situ synthesis of TiO2 rutile/anatase heterostructure by DC magnetron sputtering at room temperature and thickness effect of outermost rutile layer on photocatalysis

TiO_2 rutile/anatase heterostructure thin films with varying rutile thickness have been in-situ synthesized via DC magnetron sputtering with Ar gas at room temperature. The crystal texture, surface morphology, energy gap and optical properties of the films have been investigated by X-ray diffraction meter, grazing incidence X-ray diffraction meter, Raman spectroscopy, scanning electron microscopy, and UV–visible spectrophotometer, which indicates that the rutile/anatase heterostructure films are successfully fabricated. The further degradation experiments display that the photocatalytic activity can be dramatically affected by the thickness of the outmost rutile layer and the 100 nm thickness exhibits the best performance in all of the TiO_2 thin films. With the increase of the outmost rutile layer, the optical band gap of TiO_2 film displays a systematic decrease slightly. However,the change in photocatalytic activity does not coincide with that in the band gap. The photoresponse and electrochemical properties of the thin films have been characterized to understand the mechanism of the varied photocatalytic activity.     

Pd-MnO2 nanoparticles/TiO2 nanotube arrays (NTAs) photo-electrodes photo-catalytic properties and their ability of degrading Rhodamine B under visible light

Pd-MnO_2/TiO_2 nanotube arrays(NTAs) photo-electrodes were successfully fabricated via anodization and electro deposition subsequently; the obtained Pd-MnO_2/TiO_2 NTAs photo electrodes were analyzed by scanning electron microscopy(SEM), X-ray diffraction(XRD) and characterized accordingly. Moreover, the light harvesting and absorption properties were investigated via ultraviolet–visible diffuse reflectance spectrum(DRS); photo degradation efficiency was investigated via analyzing the photo catalytic degradation of Rhodamine B under visible illumination(xenon light). The performed analyses illustrated that Pd-MnO_2 codoped particles were successfully deposited onto the surface of the TiO_2 nanotube arrays;DRS results showed significant improvement in visible light absorption which was between400 and 700 nm. Finally, the photo catalytic degradation efficiency results of the designated organic pollutant(Rhodamine B) illustrated a superior photocatalytic(PC) efficiency of approximately 95% compared to the bare TiO_2 NTAs, which only exhibited a photo catalytic degradation efficiency of approximately 61%, thus it indicated the significant enhancement of the light absorption properties of fabricated photo electrodes and their yield of UOH radicals.     

深部储层中CO2沿断层泄漏量的影响因素

CGS（CO₂地质储存）是CO₂减排的重要手段之一,天然裂隙的存在则是CGS的潜在风险.CO₂地质储存过程中储层上覆盖层及其浅部含水层是防止CO₂泄漏的天然屏障,为了探究深部咸水层中CO₂沿断层的泄漏过程并获得断层渗透率及储层中超临界CO₂流体初始条件（初始饱和度、初始泄漏压力）对CO₂沿断层泄漏速率和泄漏量的影响程度,依据鄂尔多斯CO₂灌注工程示范区资料,使用多相、多组分溶质运移数值模拟软件TOUGH2建立了2D概念模型.结果表明,深部咸水层中的CO₂在压力差和浓度差的作用下沿断层发生泄漏,到达浅部含水层后开始发生侧向运移,100 a内运移了约200 m的水平距离;由于浮力的作用,CO₂集中在含水层顶板处,有效地防止了CO₂向外泄漏.影响因素分析表明,100 a内断层渗透性能为低渗、中渗和高渗条件时,CO₂累积泄漏量分别为0、1 050和3 000 t;CO₂初始饱和度分别为0.20、0.50和0.99时,CO₂累积泄漏量分别为550、1 050和1 650 t;初始泄漏压力分别为17.3、17.6和18.1 MPa时,CO₂累积泄漏量则分别为900、1 050和1 400 t.除此之外,断层渗透性、CO₂初始气体饱和度和初始泄漏压力对CO₂泄漏的影响还体现在泄漏发生时间和平均泄漏速率上.研究显示,各因素对CO₂沿断层泄漏过程的影响程度表现为断层渗透性能> CO₂初始饱和度> CO₂初始泄漏压力.