混合接种PN与PN/A颗粒污泥快速启动连续流自养生物脱氮反应器

在连续流条件下,快速培养亚硝化-厌氧氨氧化（PN/A）颗粒污泥是实现污水高效生物脱氮处理的关键技术. 与PN/A污泥相比,亚硝化（PN）颗粒污泥具有生长周期短、易于批量化培养的优点,并可作为富集厌氧氨氧化菌（AMX）的载体. 在3个完全混合流反应器（R1~R3）中,分别按照质量比3∶1、1∶1和1∶3混合接种PN/A和PN颗粒污泥,并通过设置高氨氮负荷、短水力停留时间和强水力剪切条件,成功启动了连续流自养生物脱氮工艺. 结果表明,尽管R3的启动时长较R1和R2更长,但污泥接种比并未显著影响连续流反应器在稳定状态下的脱氮性能,总氮去除负荷均可达到2.6 kg·（m³·d）^-1以上. 接种的PN颗粒污泥通过提供好氧氨氧化菌种（AOB）,为AMX生长供给了充足的亚硝态氮基质,充分发挥了培养PN/A颗粒污泥的前驱体作用. 由高通量测序结果可知,R1~R3中成熟颗粒的微生物丰度和多样性指数均明显高于接种污泥. AOB（Nitrosomonas属）和AMX（Candidatus Kuenenia和Brocadia属）与Chloroflexi、Bacteroidetes和Chlorobi等异养菌门是驱动自养生物脱氮和维持颗粒结构稳定的关键菌群. 总之,PN与PN/A颗粒污泥的混合接种是快速启动连续流自养脱氮工艺的可行策略,对工程应用具有指导意义.     

Abating whey organic load through ethanol and lactic acid production by kefir

Abstract

The extent to which selected ethanol and lactic acid production bioprocesses contribute to whey waste abatement was examined. Alcoholic fermentation of whey was carried out by kefir cells immobilized on grape stalks, delignified cellulosic materials, or brewer's spent grains. Lactic acid fermentation was also performed by free kefir cells with or without addition of brewer's spent grains as promoting material. Since whey fermentation rate is affected by the lactose uptake rate, ¹⁴C-labeled lactose was used to study the fermentation ability of kefir. The highest reductions in biochemical oxygen demand and chemical oxygen demand of whey, about 68% and 52%, respectively, were achieved by lactic acid fermentation in 6 h at 37 °C and pH 5.5, in the presence of 120 g brewer's spent grains. Additionally, at the same conditions, the highest ¹⁴C-labeled lactose uptake rate by kefir and consequently the highest alcoholic fermentation rate were also recorded. However, greater reductions in biochemical oxygen demand and chemical oxygen demand of whey are required prior to final disposal.     

短程硝化—厌氧氨氧化组合工艺在脱氮领域的研究进展

基于全程硝化反硝化的传统生物脱氮工艺在硝化过程中需要大量氧气供应,反硝化过程需要有机物作为碳源,存在能耗与药耗过大的问题.为了降低废水脱氮的成本,短程硝化(PN)—厌氧氨氧化(ANAMMOX)组合工艺(PNA工艺)得到了高速发展.综述了PNA工艺的影响因素,重点介绍了4种基于PN与ANAMMOX原理开发的衍生PNA工艺...     

投加聚氨酯泡沫微生物固定化载体的SBBR脱氮除磷实验研究

研究投加聚氨酯泡沫微生物固定化载体的SBBR脱氮除磷效果及机理.在SBR中填充聚氨酯泡沫微生物固定化载体,形成序批式生物膜反应器(SBBR).SBBR以实际生活污水为处理对象,在A/O运行工况下对微生物进行培养驯化,并在SBBR运行稳定时研究其脱氮除磷效果.研究结果表明,SBBR中的聚氨酯泡沫微生物固定化载体在空间上形...     

铁镍改性膨润土对废水中有机污染物的吸附性能研究

以钠基膨润土为原料,制备了铁镍无机改性土和铁镍有机复合改性土,并应用于造纸废水的处理,探讨了改性土用量、废水pH值、搅拌时间等因素对COD去除率的影响,通过正交实验对实验条件进行了优化.结果表明:铁镍有机复合改性土和铁镍元机改性土对废水的处理效果明显好于原土;膨润土的用量、废水的pH对COD的去除率影响较大;对于铁镍无机改性土,吸附剂用量为12g/L,溶液pH=2,吸附时间为10 min时,对废水中COD的去除率为54.06%;对于铁镍有机复合改性土,吸附剂用量为14g/L,溶液pH=3,吸附时间为20 min时,对废水中COD的去除率为70.10%.     

多孔硅酸钙滤料吸附床除磷试验研究

以多孔硅酸钙滤料为吸附载体处理含磷的二沉池出水.通过静态吸附试验和动态吸附试验,研究了滤料粒径及投加量、初始pH、反应时间、温度以及滤料填充高度对除磷效果的影响.在静态吸附试验中,取初始磷质量浓度为4.98 mg/L的含磷废水100 mL,当多孔硅酸钙滤料粒径为4～14目,投加量为1.0g,吸附时间为2.5h,温度为25℃,溶液初始pH为7.0～9.0时,磷的去除率可达95％以上,出水磷满足《城镇污水处理厂污染物排放标准》(GB 18918-2002)的一级A标准(≤0.5 mg/L).动态吸附试验表明,在长期运行条件下,多孔硅酸钙滤料吸附床能持续有效地去除污水中的磷,综合考虑吸附率和运行费用,选择水力停留时间为30 min,滤料填充高度为60 cm为宜.     

温度及外加碳源对生物脱氮除磷过程的影响

针对污水处理厂普遍面临的进水碳源不足及冬季低温时出水氮磷不能稳定达标的问题,研究了温度(21、15和10℃)和外加碳源(乙酸)对活性污泥缺氧条件下反硝化及释磷过程的影响。结果表明,在缺氧条件下投加乙酸,释磷与反硝化反应可同时进行,且乙酸投量的增加仅延长快速碳源反硝化阶段及缺氧释磷阶段的反应时间;温度降低为15℃和10℃时,快速碳源反硝化阶段反硝化速率及缺氧释磷速率较21℃分别降低了约29.2%、42.2%和26.1%、32.3%。当硝态氮目标去除量与磷酸盐目标释放量之比超过5时,乙酸的最优投量以满足反硝化要求为准,计算得出21、15和10℃时常州某城镇污水处理厂乙酸最优投加量计算值约为30、39和46 mg/L。     

污水低氧脱氮机制及其应用研究进展

阐述了污水低氧脱氮的基本原理,即抑制或去除亚硝酸盐氧化菌(NOB),同时保留氨氧化菌(AOB),并保持其活性;探讨了污水低氧脱氮实现途径;详细介绍了几种典型的污水低氧脱氮工艺(短程硝化(SHARON)工艺、厌氧氨氧化(ANAMMOX)工艺、好氧反氨化(DEMON)工艺、低氧自养硝化反硝化(OLAND)工艺、甲烷营养型硝化反硝化工艺和亚硝酸盐型完全自养脱氮(CANNON)工艺)的应用研究进展;最后对污水低氧脱氮处理工艺的工程运用进行了展望.     

燃煤锅炉湿式脱硫除尘一体化设备的综合分析

本文对湿式脱硫除尘一体化设备的结构和性能进行了较为全面的分析,指出了该设备存在的诸多弊病,提出了解决方案--脱硫、除尘分体组合式的思路.     

The removal of lignin and phenol from paper mill effluents by electrocoagulation

This study aims to investigate the treatment of paper mill effluents using electrocoagulation. Removal of lignin, phenol, chemical oxygen demand (COD) and biological oxygen demand (BOD) from paper mill effluents was investigated at various current intensities by using different electrodes (Al and Fe) and at various electrolysis times (1.0, 2.5, 5.0 and 7.5min). It was observed that the experiments carried out at 12V, an electrolysis time of 2min and a current intensity of 77.13mA were sufficient for the removal of these pollutants with each electrode. The removal capacities of the process using an Al electrode were 80% of lignin, 98% of phenol, 70% of BOD, and 75% of COD after 7.5min. Using an Fe electrode the removal capacities were 92%, 93%, 80% and 55%, respectively. In addition, it was found that removal of lignin, phenol, BOD and COD increased with increasing current intensity. In the experiments carried out at different current intensities, higher removal can be explained through a decrease in intra-resistance of solution and consequently an increase at the transfer speed of organic species to electrodes. It was also found that Al electrode performs higher efficiency than Fe electrode except for COD removal. However, the time required for removal of BOD was more than that of COD. The results suggest that electrocoagulation could be considered as an effective alternative to paper mill effluents treatment.