阶式生物接触氧化对富营养化太湖水源水中溶解有机物的去除性能研究

构建阶式生物接触氧化反应器处理富营养化太湖水源水,对其净水效能进行研究。结果表明,在优化工况条件下,阶式生物氧化反应器的三阶对太湖水源水中DOC的累积去除率分别为34．4％、40．2％和47．5％,对BDOC的总去除率为68．4％,除生物降解外,填料拦截、生物吸附絮凝等物理、化学作用对去除原水中的DOC仍有重要作用。DOC分子量分级表明,太湖源水中含量最大的是分子量〈500Da的DOC,含量最小的是分子量在5k～500Da间的DOC。阶式生物接触氧化反应器对分子量〈500 Da的DOC的去除率在60％以上,而出水中5k～500 Da区间的DOC含量相比原水增加近1倍。     

厌氧膨胀床处理低浓度污水的污泥颗粒和生物活性变化

污泥的聚集形态和活性,是影响厌氧反应器处理效率的关键因素。通过对厌氧膨胀床反应器（anaerobicex—pandedblanketreactor,AEBR）处理低浓度城镇污水在启动和稳定运行期的污泥活性研究,AEBR在启动运行期内,接种颗粒污泥为适应低浓度基质条件,污泥粒径经历从大变小,再重新颗粒化粒径变大的过程。在运行期第103天,粒径小于1000μm污泥的体积比达到44．7％,平均粒径为952μm,到运行期第173天,粒径小于1000μm污泥的体积比降为28％,平均粒径达1179μm,污泥重新颗粒化完成。颗粒污泥适应新的环境后,单位重量污泥的最大比产甲烷活性（specificmetha．nogensisactivity,SMA）值和胞外聚合物含量增加,分别达到112mLCH4／（gVSS·d）和215mg／gVSS。在处理实际城镇污水的AEBR反应器内,辅酶F420含量可以有效指示污泥样品的产甲烷活性,AEBR反应器不同高度位置的污泥活性不一样,反应器底部污泥活性低于中上部区域污泥的活性。     

煤制乙二醇废水预处理装置的工业化调试

针对煤制乙二醇废水含高浓度硝酸盐氮的特点,设计了缺氧膨胀床(AEB)反应器预处理装置,并进行了工业化启动和调试运行,考察了其在反硝化连续流运行条件下的处理效果及工艺参数变化。结果表明,AEB反应器启动后,填料层生物膜挂膜快速且生长稳定。反应器在工业化调试阶段运行稳定,COD和TN的去除率和去除负荷较为稳定。在受到来水冲击后,AEB反应器处理效果稳定,出水可在短期内恢复正常。该技术的系统操控参数范围较广,易于工业化操控运行,在煤制乙二醇废水和其他含高浓度硝酸盐氮废水的处理中具有较大的推广价值。     

IC反应器处理MTO废水的中试研究

中试研究了内循环(IC)反应器处理甲醇制烯烃(MTO)废水的启动和运行过程,同时考察了颗粒污泥的性状及沼气产量的变化情况。试验过程运行稳定,系统抗冲击性强。以絮状污泥为接种污泥,经过131 d的启动和运行,IC反应器的COD去除负荷可达10 kg/(m~3·d)以上,COD去除率可达90%以上。IC反应器中的成熟颗粒污泥形状规则、密实、粒径大、沉降速率快。IC反应器的沼气产量符合理论预期。     

Hydrothermal liquefaction phase behavior of microalgae & model compounds in fused silica capillary reactor

A fused silica capillary reactor combined with a heating/cooling stage, a microscope and a digital camera were used to investigate phase behavior during the hydrothermal liquefaction of microalgae (Dunaliella tertiolecta) and model compounds, including soya protein and glycine, starch, glucose and xylose, stearic acid and palmitic acid. Bubbles were generated at 246°C and disappeared at 360°C upon heating when Dunaliella tertiolecta used as feedstocks. Moreover, liquid products were generated at 300°C upon heating and oily liquid products began to separate out at 250°C upon cooling. The phase behavior of soya protein was similar to that of the Dunaliella tertiolecta. Meanwhile, there only observed the bubbles generation during hydrothermal liquefaction of glycine. Heating the starch, glucose and xylose above 350°C generated black solids from carbonization. Stearic acid and palmitic acid only had the process of melting, dissolution, dispersion and precipitation.     

ABR反应器的两种快速启动方法对比

ABR反应器的启动是ABR反应器能否高效稳定运行的关键,其影响因素很多。为了更好地实现ABR反应器的启动,提出了通过2种不同启动方法的对比,即1^#反应器采用好氧预挂膜的方法,2^#反应器采用低负荷启动法,得出的结论为,好氧预挂膜启动法的启动时间短,COD去除率高,出水pH稳定,颗粒状污泥生长情况较好,是一种可推广的启动方法。     

SBR降解动力学研究

采用SBR工艺处理有机废水,在已有工艺条件下对生物降解动力学进行了研究,得出生物降解反应为一级反应。研究表明,用Monod公式能较好反映出有机物的降解规律,确定了其动力学参数V_max=14.6306 d^-1,K_s=83.2993 mg/L,得出SBR降解动力学模型为V=14.6306X·S/(83.2993+S)。利用以动力学为基础的动态模拟法优化SBR工艺,实验结果表明该方法合理可行,对SBR的设计与运行有一定的指导作用,可作为SBR反应器扩大实验和设计的依据。     

炭纤维载体固定床厌氧发酵启动运行效果实验

以开发高效率、抗冲击性能强的高浓度有机废水沼气发酵技术为目的,用传统的 UASB反应器作为对照,研究了以炭纤维为生物膜载体的固定床厌氧反应器的启动运行效果。反应器进口废水 COD 为 5 000 mg/L, 水力停留时间 (HRT) 由213 h 逐步缩短为35 h,进水有机容积负荷(OLR)由0.56 kg COD/ (m³·d)提到3.45 kg COD/(m³·d)。结果表明,固定床反应器厌氧发酵的效率比对照高,出水 pH 值也比对照稳定;运行到第 50 d 时,固定床厌氧反应器和对照的 COD去除率分别由第 7 d 的36.56%和33.58%上升到87.9%和62.6%;固定床厌氧反应器的容积比产气率最高为1.16 m³/(m³·d),累计产气量为415.59 L,而对照的容积比产气率最高值仅为0.31 m³ /(m³·d),累计产气量为 71.66 L,前者最高容积比产气率和累计产气量分别是后者的3.74倍和5.78倍。固定床厌氧反应器的启动速度、COD 去除率和产甲烷效率显著地高于对照反应器。     

厌氧序批式反应器内挥发性脂肪酸积累特性研究

小试规模的厌氧序批式反应器（ASBR）,通过人工配水,研究了启动3个月时间以及一个运行周期内反应器内挥发性脂肪酸（VFA）的积累情况,并通过分析期间产甲烷活性的变化说明了控制VFA积累的重要性。经过近120 d的运行,乙酸和丙酸的最大比产甲烷活性分别提高了1.8和2.2倍,说明反应器的启动过程即是微生物群落的优化和选择的过程,ASBR的抗冲击的能力较强说明随启动的进行和种群的优化,活性污泥凝聚性能增强,对VFA的降解能力增强。     

Fluoride removal by a continuous flow electrocoagulation reactor

Long-term consumption of water containing excessive fluoride can lead to fluorosis of the teeth and bones. Electrocoagulation (EC) is an electrochemical technique, in which a variety of unwanted dissolved particles and suspended matter can be effectively removed from an aqueous solution by electrolysis. Continuous flow experiments with monopolar aluminium electrodes for fluoride removal were undertaken to investigate the effects of the different parameters such as: current density (12.5-50A/m(2)), flow rate (150-400 mL/min), initial pH (4-8), and initial fluoride concentration (5-25mg/L). The highest treatment efficiency was obtained for the largest current and the removal efficiency was found to be dependent on the current density, the flow rate and the initial fluoride concentration when the final pH ranged between 6 and 8. The composition of the sludge produced was analysed using the X-ray diffraction (XRD) spectrum. The strong presence of the aluminium hydroxide [Al(OH)(3)] in the above pH range, which maximizes the formation of aluminium fluoride hydroxide complex [Al(n)F(m)(OH)(3n-m)], is the main reason for defluoridation by electrocoagulation. The results obtained showed that the continuous flow electrocoagulation technology is an effective process for defluoridation of potable water supplies and could also be utilized for the defluoridation of industrial wastewater.