工业烟气氨法-络合法同时脱硫脱硝

在脱硫脱硝喷淋装置上采用氨法-络合法处理工业烟气。考察了吸收液pH、Fe(Ⅱ)EDTA浓度、初始烟气浓度、液气比对烟气同时脱硫脱硝效果的影响。实验结果表明:吸收液的酸碱度通过影响Fe(Ⅱ)与EDTA的络合形式进而影响NO去除率;SO_2去除率主要受吸收液pH和初始SO_2质量浓度的影响;当吸收液pH大于8、吸收液Fe(Ⅱ)EDTA浓度大于0.100 mol/L、初始SO_2质量浓度小于1 500 mg/m3、初始NO质量浓度为1 200 mg/m3时,SO_2去除率均在95%以上,NO去除率为54%;当液气比由1 L/m3增大至4 L/m3时,有效脱硫时间和有效脱硝时间分别增长了7 min和4 min。     

废弃印刷线路板碘化法浸金研究

针对碘化法从废弃印刷线路板中提取金的工艺设计,分别考察了碘的质量分数、n(I₂)/n(I^-)比值、固液比、双氧水的质量分数、pH值、浸出时间和浸出温度对金浸出率的影响。结合正交设计优化实验方法,提出了从废弃印刷线路板中碘化法浸取金的最佳工艺条件：碘的质量分数为1.1％,n(I₂)∶n(I^-)=1∶10,双氧水的质量分数为1.5％,浸出时间4 h,固液比为1∶10,浸出温度为常温（25℃）,溶液pH值为中性,此时金浸出率可达97.5％。     

基于生态安全的DAT-IAT城市污水处理工艺改进研究

通过正交试验,得到了DAT-IAT工艺和A/DAT-IAT工艺处理城市污水的常规指标去除和生态毒理指标削减的最优运行条件。结果表明,在正交试验的同一工艺中,COD去除最优运行条件的出水COD值优于生态毒性削减最优运行条件的出水COD值,但前者出水的生态毒性较大。由于厌氧池的水解酸化作用,A/DAT-IAT工艺对COD和生态毒性的处理效果均优于DAT-IAT工艺,并且回流总能耗低于DAT-IAT工艺,但是出水COD仍不达标。为了降低进入工艺的COD的总量,以絮凝沉淀做为预处理工艺,并采用Al残留量最小的絮凝剂投药量以降低出水中残留Al带来的生态风险。结果表明,在COD去除最优运行条件下,具有絮凝预处理的工艺对COD的去除效果优于没有絮凝预处理的工艺。絮凝-A/DAT-IAT工艺在COD去除最优运行条件下出水COD为104.46 mg/L,满足排放标准。在毒性削减最优运行条件下,具有絮凝预处理的工艺的出水生态毒性有所上升,但是污染物的总量得到了大幅削减。絮凝-A/DAT-IAT工艺与DAT-IAT工艺相比,在污染物去除效率得到大幅增加的同时,生态毒性得到有效控制,生态安全得到了有效的保障。     

微曝气Fenton氧化法处理模拟双酚A废水的效果及其生物验证

研究了微曝气Fenton氧化法关键工艺参数对模拟双酚A（BPA）废水处理效果的影响,并从活性污泥性质和污染物去除率两方面,采用膜生物反应器(membrane bioreactor, MBR)对微曝气Fenton氧化法的处理效果进行了实验验证,为实现BPA废水的生物处理奠定基础。结果表明,初始pH值、反应时间、H₂O₂/COD(质量浓度比)、H₂O₂/Fe²⁺ (摩尔浓度比)、反应温度及曝气量均对预处理效果有较大影响,在最佳条件下,COD去除率可达70%,BOD/COD值则由原废水的0.02提高到0.50以上。MBR处理上述出水的结果表明,经微曝气Fenton氧化处理BPA的废水,可较好地适应后续的生化处理。     

基于超临界水氧化过程的能源环境系统设计

阐述了超临界水氧化过程的工艺路线,介绍了超临界水氧化过程的特点,提出了基于超临界水氧化过程的能源环境系统,设计了几种热量与能量回收系统程的耦合工艺,为提高超临界水氧化过程的经济性奠定了基础。     

太阳光Fenton法处理垃圾渗滤液中有机污染物

研究利用太阳光Fenton法处理垃圾渗滤液。根据太阳光辐射强度随时间的变化规律,选择重庆7、8月份的晴天,在中午12：00到下午14：00时进行试验,研究太阳光辐射时间、pH值、Fenton试剂用量对垃圾渗滤液COD去除率的影响。研究结果表明：太阳光Fenton法对垃圾渗滤液的COD有较好的去除效果,COD去除率达86.2%。太阳光Fenton法处理垃圾渗滤液的优化条件是：日光辐射时间为120 min,pH值为2.5,Fe²⁺浓度为5 mmol/L,H₂O₂浓度为570 mmol/L。同时,论文还对太阳光Fenton法处理垃圾渗滤液的动力学进行分析。研究结果显示：太阳光Fenton法处理垃圾渗滤液,其表观动力学方程为-dC/dt=2.6×10^-8×P^1.92×F^1.79×E^1.67。     

Landfill site selection using spatial information technologies and AHP: A case study in Beijing,China

Site selection is an important and necessary issue for waste management in fast-growing regions. Because of the complexity of waste management systems, the selection of the appropriate solid waste landfill site requires consideration of multiple alternative solutions and evaluation criteria. Based on actual conditions of the study area, we considered economic factors, calculated criteria weights using the analytical hierarchy process (AHP), and built a hierarchy model for solving the solid waste landfill site-selection problem in Beijing, China. A geographic information system (GIS) was used to manipulate and present spatial data. All maps are graded from 1 (lowest suitability) to 5 (highest suitability) using spatial information technologies. The candidate sites were determined by aggregation based on the criteria weights. The candidate sites are divided by ‘best’, ‘good’ and ‘unsuitable’ landfill areas. Best landfill areas represent optimal sites; good landfill areas can be used as back-up candidate sites. Our work offers a siting methodology and provides essential support for decision-makers in the assessment of waste management problems in Beijing and other rapidly developing cities in developing countries.     

阳离子染料废水治理技术

介绍了阳离子染料废水的特点,以及近年来阳离子染料废水的各种处理技术,并对阳离子染料废水处理技术的发展进行了展望,指出阳离子废水处理技术正朝着各种工艺优化组合的方向发展。     

Liquefaction process for a hydrothermally treated waste mixture containing plastics

Most landfilled plastic waste is a mixture or is in the form of composites with incombustible wastes such as glass, metals, and ceramics. After hydrothermal treatment, including a steam-explosion process, the separation of mixed waste (MW) into organic and inorganic substances becomes easy. However, the effect of hydrothermal pretreatment on the subsequent liquefaction of organic substances from MW is not obvious. In this study, the effects on the liquefaction of polystyrene and high-density polyethylene are discussed. Moreover, optimum conditions for the liquefaction of organic substances from hydrothermally treated MW are identified. By means of this hydrothermal pretreatment, including the steam-explosion process, polystyrene and high-density polyethylene can be significantly converted to oil by liquefaction at 300°–400°C. In comparison with liquefaction of hydrothermally pretreated mixed waste (HMW) at 300°–400°C with a batch type reactor, the yield of oil increases significantly on liquefaction using a semi-batch type reactor. It is considered that the radical chain and termination reactions among the radicals from HMW were inhibited in the semi-batch type reactor. On liquefaction of HMW in a semi-batch reactor, the conversion of HMW to oil was enhanced on increasing the liquefaction temperature to 350°C and the holding time to 60 min. Chemical Feedstock Recycling & Other Innovative Recycling Techniques 6     

循环半干法脱硫除尘设备布置于两串联引风机之间的工程实践

介绍了宁夏国电大武口发电厂2×110MW机组脱硫、除尘改造系统的配置形式,通过实际工程应用,分析各种因素对该布置形式脱硫、除尘系统的影响,并对出现的问题提出解决办法,为同类改造工程提供参考。