建筑风载数值模拟的影响因素

通过对建筑物周围风场的计算流体动力学(CFD)模拟计算与原型试验结果的比较,分析了在应用CFD计算时应该考虑的计算区域、进口边界条件、湍流模型和网格划分等各种相关因素对CFD数值模拟结果准确度的影响.结果表明,在各种影响因素中,计算区域影响相对较小,而进口边界条件、网格划分和湍流模型的影响相对较大;而且进口边界条件中速度分布对计算结果的影响大于湍流强度分布对计算结果的影响,是进口边界条件中的关键部分.同时,根据上述比较,建议在网格划分中,对几何外形简单的单个建筑的数值模拟计算,优先采用结构化网格划分方法;对于湍流模型的选择,一般的工程应用中,建议在初步设计阶段选择RNGκ-ε湍流模型,而在最终设计阶段采用雷诺应力模型.     

浅谈利用地下盐穴处理废钻井液

利用地下盐穴进行各种工业废物的埋藏处理目前在国外已得到很好的应用。文章针对油田废钻井液的填埋处理技术,详述了建设盐穴所需要选择的地质条件:必须具有良好的封闭性;造穴方式主要通过水溶洗盐形成地下溶洞;埋藏废物需要通过一系列的特定工艺才能完成;废钻井液埋藏处理后需要进行监测以防止产生污染事故。一般来说,由于地下盐穴埋深大、盐穴封闭性好,具有较高的安全性。利用盐穴进行废钻井液的埋藏具有费用低、容量大、占地少、安全性高等优点。     

寒区多孔介质中LNAPL迁移的多场耦合模拟

建立了包含水、气、NAPL、固(冰)四相的温度场、流场及化学场多场耦合模型,适用于定量模拟LNAPL泄漏过程中发生冻结后的迁移分布.通过与非冻条件下LNAPL迁移模型对比,模拟结果显示,冻结条件下因冰的形成LNAPL会发生与非冻条件下不同的迁移行为,冰的形成阻碍LNAPL下渗,并产生冻结势使LNAPL向地表方向迁移.相...     

改性PVDF中空纤维膜处理压裂返排液研究

针对中空纤维膜应用于水力压裂返排液处理时存在的膜污染严重、通量衰减快、影响处理效率等问题,研究了PVDF固含量、凝固浴温度等因素对PVDF膜性能的影响,通过非溶剂致相分离法制备了PVDF中空纤维膜,并采用表面接枝技术,对PVDF中空纤维膜进行了表面亲水化改性。压裂返排液吸附实验结果表明,表面接枝降低了PVDF的接触角,提高了膜的亲水性。与未接枝改性的PVDF膜相比,亲水改性后的PVDF膜表面吸附的压裂返排液更少。将亲水性中空纤维膜用于页岩气水力压裂返排液的过滤处理,应用结果表明其对压裂返排液中的总铁、SS、浊度、细菌去除率达到90%以上,长时间运行后的通量保持率高,有较好的抗膜污染性。     

Consequence prediction for dust explosions involving interconnected vessels using computational fluid dynamics modeling

Combustible dust explosions continue to present a significant threat toward operating personnel and pneumatic conveyance equipment in a wide variety of processing industries. Following ignition of suspended fuel within a primary enclosure volume, propagation of flame and pressure fronts toward upstream or downstream interconnected enclosures can result in devastating secondary explosions if not impeded through an appropriate isolation mechanism. In such occurrences, an accelerated flame front may result in flame jet ignition within the secondary vessel, greatly increasing the overall explosion severity. Unlike an isolated deflagration event with quantifiable reduced pressures (vent sizing according to NFPA 68 guidance), oscillation of pressure between primary and secondary process vessels leads to uncertain overpressure effects. Dependent on details of the application such as relative enclosure volumes, relief area, fuel type, suspended concentration, duct size, and duct length, the maximum system pressure in both interconnected vessels can be unpredictable. This study proposes the use of FLame ACceleration Simulator (FLACS) computational fluid dynamics (CFD) modeling to provide reliable consequence predictions for specific case scenarios of dust deflagrations involving interconnected equipment. Required minimum supplement to the originally calculated relief area (A_v) was determined through iterative simulation, allowing for reduced explosion pressures (P_red) to be maintained below theoretical enclosure design strengths (P_es).     

Optimization of gas detector placement considering scenario probability and detector reliability in oil refinery installation

Gas detection system is a critical layer of protection in process safety. Leak scenario probability and detector reliability are two key factors in the optimization of gas detector placement. However, they are easily neglected in previous studies, which may lead to an inaccurate evaluation of the optimization solutions. In this study, a stochastic programming (SP) optimization method is proposed considering these two factors. In order to quantitatively represent the probability of leak scenarios, a complete accident scenario set (CASS) is built combining leak sources and wind fields. Then, the computational fluid dynamics (CFD) method is adopted for consequence modeling of gas dispersion. The Markov model is developed to predict the detector reliability. With the objective of minimal cumulative detection time (MCDT), the SP formulation considering scenario probability and detector reliability (MCDT-SPR) is proposed. By introducing the particle swarm optimization (PSO) algorithm, the optimization formulations can be solved. A case study is investigated on a diesel hydrogenation refining unit. Results validate this approach is promising to improve the detection efficiency. This method is more practical and matching with the actual industrial environment, where the leak scenarios and the detector reliability can change dynamically in real process setting.     

Hazard analysis on LPG fireball of road tanker BLEVE based on CFD simulation

In order to research the hydrocarbon fireball characteristic of LPG tanker Boiled Liquid Evaporate Vapor Explosion (BLEVE) under different conditions, computational fluid dynamics (CFD) simulations of the hydrocarbon fireballs from the LPG tanker BLEVE accidents were carried out. Several new different factors, such as the mass of fuel, inlet velocity and airflow velocity, were considered to analyze the influence on the evolution of the characteristics of the fireball and the development of the LPG tanker BLEVE accidents. Results indicate that the fireball with a greater mass of fuel radiates more heat but slower. The large longitudinal diameter of the fireball and high radiation heat flux are observed in case of a faster inlet velocity used for the same mass. The airflow was found to shorten the initial phase of the fireball effectively. Some suggestions were proposed to prevent the LPG BLEVE accidents. Analysis performed show that various parameters like fireball diameter, radiative heat flux and lifting speed of fireball can be predicted well using FDS code.     

废弃饱和盐水钻井液的固液分离

采用化学破胶脱稳和压滤机械分离的化学强化固液分离技术处理江汉油田废弃饱和盐水钻井液(简称废钻井液).最佳固液分离工艺为:调节废钻井液的pH为6.5左右,先加入无机破胶剂(HWJ),HWJ的加入量为15 000 mg/L,以400 r/min的转速搅拌3 min,稀释1倍后,再加入有机破胶剂(HYJ),HYJ的加入量为300 mg/L,以120 r/min的转速搅拌5min.固液分离结果表明,分离后出水率达68.2%,而泥饼湿含量只有55.8%,废钻井液的COD由67 886.8 mg/L降至8 898.9 mg/L.     

废弃印刷线路板中材料的资源化回收利用技术

废弃印刷线路板（WPCBs）既有污染环境的一面,又有可资源化回收利用的一面.通过机械物理法、热解、超临界流体氧化和离子液体溶解等方法对其进行分离和回收金属和非金属材料.初步分选的金属需要进一步提纯以实现高附加值.而非金属材料可以用热解法、微波处理、超临界流体技术、等离子技术等技术进行产气和能量回收,也可以通过制备建筑材料或填料和其它功能村料进行物料回收.总之,对WPCBs进行适当地处理不但可以减轻环境压力,还可以变废为宝,实现资源再生利用.     

旋风分离器内高速旋转流场的数值计算方法选择

数值计算方法已成为研究旋风分离器内部流场的重要途径。利用计算流体力学方法对旋风分离器内部气相流场进行了数值模拟研究。分析了不同湍流模型、离散化方式和压力插值方式对旋风分离器内部计算流场的影响,并将所得数值结果与已知的实验数据进行了对比,以期得到最适合的数值模型。结果表明:对于旋风分离器内部复杂流场的流动,运用雷诺应力模型(Low-Re Stress-Omega)能够较好地预测出强制涡中心涡流的运动情况,同时采用SIMPLEC算法、二阶迎风离散化方式和PRESTO压力梯度插补格式能够获得最好的预报结果。