场地含水层氯代烃污染物自然衰减机制与纳米铁修复技术的研究进展

综述了国际上典型工业场地有机溶剂污染物在地下水中的自然衰减机制及修复技术的研究现状和发展趋势.场地地下水修复技术从抽出-处理发展到治理污染源区和污染羽的纳米铁技术,涌现出-大批较为成熟的联合化学与微生物修复技术,其中潜力较大的有治理污染羽的渗透反应墙、原位化学氧化、原位化学还原、微生物强化降解及基于监测的自然衰减等.文...     

Does the Temporal Resolution of Precipitation Input Influence the Simulated Hydrological Components Employing the SWAT Model?

This study aimed to evaluate the influence of sub‐daily precipitation time steps on model performance and hydrological components by applying the Green and Ampt infiltration method using the Soil and Water Assessment Tool (SWAT). Precipitation was measured at a resolution of 0.1 mm and aggregated to 5‐, 15‐, 30‐, and 60‐min time steps. Daily discharge data over a 10‐year period were used to calibrate and validate the model. Following a global sensitivity analysis, relevant parameters were optimized through an automatic calibration procedure using SWAT‐CUP for each time step. Daily performance statistics were almost equal among all four time steps (NSE ≈ 0.47). Discharge mainly consisted of groundwater flow (55%) and tile flow (42%), in reasonable proportions for the investigated catchment. In conclusion, model outputs were almost identical, showing simulations responded nearly independently of the chosen precipitation time step. This held true for (1) the selection of sensitive parameters, (2) performance statistics, (3) the shape of the hydrographs, and (4) flow components. However, a scenario analysis revealed that the precipitation time step becomes important when saturated hydraulic conductivities are low and curve numbers are high. The study suggests that there is no need in using precipitation time steps <1 h for lowland catchments dominated by soils with a low surface runoff potential if daily flow values are being considered. Editor's note : This paper is part of the featured series on SWAT Applications for Emerging Hydrologic and Water Quality Challenges. See the February 2017 issue for the introduction and background to the series.     

Rapid genetic erosion in pollutant-exposed experimental chironomid populations

Few studies have evaluated how effectively environmental contamination may reduce genetic diversity of a population. Here, we chose a laboratory approach in order to test if tributyltin (TBT) exposure at environmentally relevant concentrations leads to reduced genetic variation in the midge Chironomus riparius. Two TBT-exposed and two unexposed experimental populations were reared simultaneously in the laboratory for 12 generations. We recorded several life-history traits in each generation and monitored genetic variation over time using five variable microsatellite markers. TBT-exposed strains showed increased larval mortality (treatments: 43.8%; controls: 27.8%), slightly reduced reproductive output, and delayed larval development. Reduction of genetic variation was strongest and only significant in the TBT-exposed strains (treatments: −45.9%, controls: −24.4% of initial heterozygosity) after 12 generations. Our findings document that chemical pollution may lead to a rapid decrease in genetic diversity, which has important implications for conservation strategies and ecological management in polluted environments.     

Batch sorption dynamics and equilibrium for the removal of lead ions from aqueous phase using activated carbon developed from coffee residue activated with zinc chloride

Lignocellulosic materials are good precursors for the production of activated carbon. In this work, coffee residue has been used as raw material in the preparation of powder activated carbon by the method of chemical activation with zinc chloride for the sorption of Pb(II) from dilute aqueous solutions.The influence of impregnation ratio (ZnCl₂/coffee residue) on the physical and chemical properties of the prepared carbons was studied in order to optimize this parameter. The optimum experimental condition for preparing predominantly microporous activated carbons with high pore surface area (890 m²/g) and micropore volume (0.772 cm³/g) is an impregnation ratio of 100%. The developed activated carbon shows substantial capability to sorb lead(II) ions from aqueous solutions and for relative impregnation ratios of 75 and 100%, the maximum uptake is practically the same. Thus, 75% represents the optimal impregnation ratio.Batch experiments were conducted to study the effects of the main parameters such as contact time, initial concentration of Pb(II), solution pH, ionic strength and temperature. The maximum uptake of lead(II) at 25 °C was about 63 mg/g of adsorbent at pH 5.8, initial Pb(II) concentration of 10 mg/L, agitation speed of 200 rpm and ionic strength of 0.005 M. The kinetic data were fitted to the models of pseudo-first order and pseudo-second order, and follow closely the pseudo-second order model. Equilibrium sorption isotherms of Pb(II) were analyzed by the Langmuir, Freundlich and Temkin isotherm models. The Freundlich model gives a better fit than the others.Results from this study suggest that activated carbon produced from coffee residue is an effective adsorbent for the removal of lead from aqueous solutions and that ZnCl₂ is a suitable activating agent for the preparation of high-porosity carbons.     

Fluoride removal by a continuous flow electrocoagulation reactor

Long-term consumption of water containing excessive fluoride can lead to fluorosis of the teeth and bones. Electrocoagulation (EC) is an electrochemical technique, in which a variety of unwanted dissolved particles and suspended matter can be effectively removed from an aqueous solution by electrolysis. Continuous flow experiments with monopolar aluminium electrodes for fluoride removal were undertaken to investigate the effects of the different parameters such as: current density (12.5-50A/m(2)), flow rate (150-400 mL/min), initial pH (4-8), and initial fluoride concentration (5-25mg/L). The highest treatment efficiency was obtained for the largest current and the removal efficiency was found to be dependent on the current density, the flow rate and the initial fluoride concentration when the final pH ranged between 6 and 8. The composition of the sludge produced was analysed using the X-ray diffraction (XRD) spectrum. The strong presence of the aluminium hydroxide [Al(OH)(3)] in the above pH range, which maximizes the formation of aluminium fluoride hydroxide complex [Al(n)F(m)(OH)(3n-m)], is the main reason for defluoridation by electrocoagulation. The results obtained showed that the continuous flow electrocoagulation technology is an effective process for defluoridation of potable water supplies and could also be utilized for the defluoridation of industrial wastewater.     

Study on the hydrolysis/precipitation behavior of Keggin Al13 and Al30 polymers in polyaluminum solutions

The hydrolysis/precipitation behaviors of Al³⁺, Al₁₃ and Al₃₀ under conditions typical for flocculation in water treatment were investigated by studying the particulates' size development, charge characteristics, chemical species and speciation transformation of coagulant hydrolysis precipitates. The optimal pH conditions for hydrolysis precipitates formation for AlCl₃, PAC_Al13 and PAC_Al30 were 6.5–7.5, 8.5–9.5, and 7.5–9.5, respectively. The precipitates' formation rate increased with the increase in dosage, and the relative rates were AlCl₃ ? PAC_Al30 > PAC_Al13. The precipitates' size increased when the dosage increased from 50 μM to 200 μM, but it decreased when the dosage increased to 800 μM. The Zeta potential of coagulant hydrolysis precipitates decreased with the increase in pH for the three coagulants. The iso-electric points of the freshly formed precipitates for AlCl₃, PAC_Al13 and PAC_Al30 were 7.3, 9.6 and 9.2, respectively. The Zeta potentials of AlCl₃ hydrolysis precipitates were lower than those of PAC_Al13 and PAC_Al30 when pH > 5.0. The Zeta potential of PAC_Al30 hydrolysis precipitates was higher than that of PAC_Al13 at the acidic side, but lower at the alkaline side. The dosage had no obvious effect on the Zeta potential of hydrolysis precipitates under fixed pH conditions. The increase in Zeta potential with the increase in dosage under uncontrolled pH conditions was due to the pH depression caused by coagulant addition. Al–Ferron research indicated that the hydrolysis precipitates of AlCl₃ were composed of amorphous Al(OH)₃ precipitates, but those of PAC_Al13 and PAC_Al30 were composed of aggregates of Al₁₃ and Al₃₀, respectively. Al³⁺ was the most un-stable species in coagulants, and its hydrolysis was remarkably influenced by solution pH. Al₁₃ and Al₃₀ species were very stable, and solution pH and aging had little effect on the chemical species of their hydrolysis products. The research method involving coagulant hydrolysis precipitates based on Al–Ferron reaction kinetics was studied in detail. The Al species classification based on complex reaction kinetic of hydrolysis precipitates and Ferron reagent was different from that measured in a conventional coagulant assay using the Al–Ferron method. The chemical composition of Al_a, Al_b and Al_c depended on coagulant and solution pH. The Al_b measured in the current case was different from Keggin Al₁₃, and the high Al_b content in the AlCl₃ hydrolysis precipitates could not used as testimony that most of the Al³⁺ was converted to highly charged Al₁₃ species during AlCl₃ coagulation.     

Effects of acute γ-irradiation on the aquatic microbial microcosm in comparison with chemicals

Effects of acute γ-irradiation were investigated in the aquatic microcosm consisting of green algae (Chlorella sp. and Scenedesmus sp.) and a blue–green alga (Tolypothrix sp.) as producers; an oligochaete (Aeolosoma hemprichi), rotifers (Lecane sp. and Philodina sp.) and a ciliate protozoan (Cyclidium glaucoma) as consumers; and more than four species of bacteria as decomposers. At 100 Gy, populations were not affected in any taxa. At 500–5000 Gy, one or three taxa died out and populations of two or three taxa decreased over time, while that of Tolypothrix sp. increased. This Tolypothrix sp. increase was likely an indirect effect due to interspecies interactions. The principal response curve analysis revealed that the main trend of the effects was a dose-dependent population decrease. For a better understanding of radiation risks in aquatic microbial communities, effect doses of γ-rays compared with copper, herbicides and detergents were evaluated using the radiochemoecological conceptual model and the effect index for microcosm.     

近50年鄱阳湖五大流域降水变化特征研究

基于鄱阳湖流域在江西省内部分对应的79县市气象站1960～2006年逐日降水观测资料,采用线性回归的方法分别研究五大流域的年降水量、降水日数、暴雨日数等3要素的变化趋势,并用Mann法进行了变化趋势的显著性检验,用距平与均方差之比达到15和20作为气候异常检验指标,对各流域的各时间序列进行了异常检验,采用了Mann Kendall法对各时间序列进行突变检测。结果表明：（1）各流域的年降水量变化趋势基本一致,年降水量与年暴雨日数密切相关;饶河流域强降水事件较多,降水强度大,赣江中游流域降水时间分布相对较均匀,强降水事件较少;（2）各流域年降水量、暴雨日数总体呈波动上升趋势,20世纪90年代以来暴雨日数异常偏多的概率最大;（3）年降水日数以20世纪80年代中期为界,之前呈波动上升趋势,之后呈波动下降趋势,2002年至今各流域降雨日数明显偏少;（4）各流域的年降水量、降水日数、暴雨日数均未出现趋势性的突变;（5）近50年来鄱阳湖流域降水时间分布不均的情况加剧,旱涝灾害风险增加。     

Combined use of molecular biology taxonomy, Raman spectrometry, and ESEM imaging to study natural biofilms grown on filter materials at waterworks

DNA-based population analysis was applied in combination with Raman spectrometry and Environmental Scanning Electron Microscopy for the characterisation of natural biofilms from sand and activated carbon filters operated for a long term at a municipal waterworks. Whereas the molecular biology polymerase chain reaction combined with denaturing gradient gel electrophoresis approach provides a deeper insight into the bacterial biofilm diversities, Raman spectrometry analyses the chemical composition of the extracellular polymer substances (EPS), microorganisms embedded in EPS as well as other substances inside biofilm (inorganic compounds and humic substances). Microscopy images the spatial distribution of biofilms on the two different filter materials. In addition, bacterial bulk water populations were compared with biofilm consortia using the molecular fingerprint technique mentioned.Population analysis demonstrated the presence of more diverse bacterial species embedded in a matrix of EPS (polysaccharides, peptides, and nucleic acids) on the sand filter materials. In contrast to this, activated carbon granules were colonised by reduced numbers of bacterial species in biofilms. Besides α-, β-, and γ-Proteobacteria, a noticeable specific colonisation with Actinobacteria was found on activated carbon particles. Here, the reduced biofilm formation came along with a decreased EPS synthesis. The taxonomy profiles of the different biofilms revealed up to 60% similarity on the same filter materials and 32% similarity of different materials. Similarity of adherent communities from filter materials and bulk water populations from the filter effluent varied between 36% and 58% in sand filters and 6–40% in granular activated carbon filters.The biofilm investigation protocols are most crucial to subsequent acquisition of knowledge on biofilm dynamics and bacterial contributions to transformation or adsorption processes in waterworks facilities.     

Sensitivity and Uncertainty of Ground‐Water Discharge Estimates for Semiarid Shrublands1

Abstract: We proposed a step‐by‐step approach to quantify the sensitivity of ground‐water discharge by evapotranspiration (ET) to three categories of independent input variables. To illustrate the approach, we adopt a basic ground‐water discharge estimation model, in which the volume of ground water lost to ET was computed as the product of the ground‐water discharge rate and the associated area. The ground‐water discharge rate was assumed to equal the ET rate minus local precipitation. The objective of this study is to outline a step‐by‐step procedure to quantify the contributions from individual independent variable uncertainties to the uncertainty of total ground‐water discharge estimates; the independent variables include ET rates of individual ET units, areas associated with the ET units, and precipitation in each subbasin. The specific goal is to guide future characterization efforts by better targeting data collection for those variables most responsible for uncertainty in ground‐water discharge estimates. The influential independent variables to be included in the sensitivity analysis are first selected based on the physical characteristics and model structure. Both regression coefficients and standardized regression coefficients for the selected independent variables are calculated using the results from sampling‐based Monte Carlo simulations. Results illustrate that, while as many as 630 independent variables potentially contribute to the calculation of the total annual ground‐water discharge for the case study area, a selection of seven independent variables could be used to develop an accurate regression model, accounting for more than 96% of the total variance in ground‐water discharge. Results indicate that the variability of ET rate for moderately dense desert shrubland contributes to about 75% of the variance in the total ground‐water discharge estimates. These results point to a need to better quantify ET rates for moderately dense shrubland to reduce overall uncertainty in estimates of ground‐water discharge. While the approach proposed here uses a basic ground‐water discharge model taken from an earlier study, the procedure of quantifying uncertainty and sensitivity can be generalized to handle other types of environmental models involving large numbers of independent variables.