Mitigation of CO2 Emissions from the EU-15 Building Stock. Beyond the EU Directive on the Energy Performance of Buildings (9 pp)

-

Goal Scope and Background. The European Directive on Energy Performance of Buildings which came into force 16 December 2002 will be implemented in the legislation of Member States by 4 January 2006. In addition to the aim of improving the overall energy efficiency of new buildings, large existing buildings will become a target for improvement, as soon as they undergo significant renovation. The building sector is responsible for about 40% of Europe's total end energy consumption and hence this Directive is an important step for the European Union in order that it should reach the level of saving required by the Kyoto Agreement. In this the EU is committed to reduce CO2 emissions relative to the base year of 1990 by 8 per cent, by 2010. But what will be the impact of the new Directive, how large could be the impacts of extending the obligation for energy efficiency retrofitting towards smaller buildings? Can improvement of the insulation offset or reduce the growing energy consumption from the increasing installation of cooling installations? EURIMA, the European Insulation Manufacturers Association and EuroACE, the European Alliance of Companies for Energy Efficiency in Buildings, asked Ecofys to address these questions.

Methods

The effect of the EPB Directive on the emissions associated with the heating energy consumption of the total EU 15 building stock has been examined in a model calculation, using the Built Environment Analysis Model (BEAM), which was developed by Ecofys to investigate energy saving measures in the building stock. The great complexity of the EU-15 building stock had to be simplified by examining five standard buildings with eight insulation standards, which are assigned to building age and renovation status. Furthermore, three climatic regions (cold, moderate, warm) were distinguished for the calculation of the heating energy demand. This gave a basic 210 building types for which the heating energy demand and CO2 emissions from heating were calculated according to the principles of the European Norm EN 832.

Results and Discussion

The model calculations demonstrates that the main contributor to the total heating related CO2 emissions of 725 Mt/a from the EU building stock in 2002 is the residential sector (77%) while the remaining 23% originates from non-residential buildings. In the residential sector, single-family houses represent the largest group responsible for 60% of the total CO2 emissions equivalent to 435 Mt/a.

-

- The technical potential: If all retrofit measures in the scope of the Directive were realised immediately for the complete residential and non-residential building stock the overall CO2 emission savings would add up to 82 Mt/a. An additional saving potential compared to the Directive of 69 Mt/a would be created if the scope of the Directive was extended to cover retrofit measures in multi-family dwellings (200-1000m2) and non-residential buildings smaller than 1000m2 used floor space. In addition including the large group of single-family dwellings would lead to a potential for additional CO2 emission reductions compared to the Directive of 316 Mt/a.

-

- Temporal mobilization of the potential: Calculations based on the building stock as it develops over time with average retrofit rates demonstrated that regulations introduced following the EPB Directive result in a CO2 emissions decrease of 34 Mt/a by the year 2010 compared to the business as usual scenario. Extending the scope of the EPB Directive to all residential buildings (including single and multi-family dwellings), the CO2 emission savings potential over the 'business as usual' scenario could be doubled to 69 Mt/a in the year 2010. This creates an additional saving potential compared to the Directive of 36 Mt/a.

-

- Cooling demand: The analysis demonstrated that in warm climatic zones the cooling demand can be reduced drastically by a combination of lowering the internal heat loads and by improved insulation. With the reduction of the heat loads to a moderate level the cooling demand, e.g. of a terraced house located in Madrid, can be reduced by an additional 85% if the insulation level is improved appropriately.

Conclusions

This study demonstrates that the European Directive on Energy Performance of Buildings will have a significant impact on the CO2 emissions of the European building stock. The main saving potential lies in insulation of the existing building stock. Beyond this, CO2 emissions could, however, be greatly reduced if the scope of the Directive were to be extended to include retrofit of smaller buildings.

Recommendation and Perspective

The reductions should be seen in relation to the remaining gap of 190 Mt CO2 eq. per annum between the current emission levels of EU-15 and the target under the Kyoto-Protocol for the year 2010. The energy and industrial sector will probably contribute only a fraction of this reduction via the newly established EU emissions trading scheme and connected projects under the flexible mechanism. In addition, the traffic sector is likely to continue its growth path leading to a widening of the gap. Thus, there is likely to be considerable pressure on the EU building sector to contribute to the EU climate targets beyond what will be achieved by means of the current EPB Directive. Legislators on the EU and national level are therefore advised to take accelerated actions to tap the very significant emission reduction potentials available in the EU building stock.     

模拟海洋全浸区环境下A517海工钢的腐蚀机理研究

目的 探究 A517 海工钢在海洋全浸区环境下的腐蚀机理。方法 通过模拟海洋全浸区腐蚀环境,利用失重法、SEM、EDS、XRD、电化学等测试技术,分析A517钢的腐蚀行为历程,并探讨其在全浸区的腐蚀机理。结果A517钢在厚度方向上的最大电位差为 13 mV,小于发生电偶腐蚀的最小电位差50mV,说明材料在厚度方向上的腐蚀敏感性一致。随浸泡时间的延长,腐蚀质量损失量逐渐增加,平均腐蚀速率先降低、后升高、最后趋于稳定,腐蚀速率约为 0.127 mm/a。结论 腐蚀动力初期主要是由溶解氧的极限扩散控制,后期则是腐蚀产物的氧化还原电荷转移控制。腐蚀首先在 Al₂O₃、MgO 等夹杂物处萌生扩展,腐蚀产物出现明显的分层现象,外锈层主要是疏松易脱落的γ-FeOOH,内锈层主要是致密均匀的 Fe₃O₄,同时锈层中还检测到了β-FeOOH和α-FeOOH的存在。锈层中存在大量微裂纹,削弱了产物膜的保护作用,促进了腐蚀的进行。     

苯作业工人外周血淋巴细胞的细胞遗传学分析

选用外周血淋巴细胞染色体畸变（CA）率和微核细胞（MN）率两项指标对两个厂苯作业工人进行了研究分析,结果表明,在3种平均浓度54,108和219mg/m³,苯接触组和对照组比较CA率和MN率均有显著性差异,且未发现二者间有线性相关,提示二者形成机制不完全相同,且较低浓度下苯的遗传毒性应引起重视。     

土壤反硝化田间原位测定方法的研究进展

土壤中的反硝化作用由于直接影响到肥料氮的利用率和环境问题,仍然是氮素研究领域的热点和难点之一,而反硝化作用研究的进展在很大程度上依赖与土壤反硝化的田间测定方法的建立。文章就目前反硝化研究领域常用的15N平衡差值法、15N示踪气体通量法、乙炔抑制气室法、乙炔抑制土柱法的原理、气体样的采集、测定和计算作了综述,以期为土壤反硝化的研究提供依据。     

Analysis of Products Generated from the Thermal and Catalytic Degradation of Pure and Waste Polyolefins using Py-GC/MS

The possibility of transforming waste plastics into valuable hydrocarbons via catalytic cracking and reforming is attracting increasing interest. Pyrolysis coupled with Gas Chromatographic separation and Mass Spectrometry detection (Py-GC/MS) has been used in this work to study the product selectivity of various catalysts in the conversion of pure and residual polyethylene samples into hydrocarbon products. Five acid solids of comparable aluminium contents but different textural and acid properties were tested as catalysts, including three zeolites (standard ZSM-5, nanocrystalline n-ZSM-5 and Beta) and two mesostructured solids (Al-MCM-41 and Al-SBA-15). Thermal cracking of the pure and residual polymers generated a similar range of products to each other, with a high proportion of linear paraffins and olefins of varying lengths. The presence of zeolitic materials resulted in complete elimination of heavy linear products, an increase in the light hydrocarbon fraction and a marked selectivity towards the formation of single-ring aromatic species, particularly benzene, toluene and xylene. Aromatic formation was particularly notable with the small crystal size n-ZSM-5 (aromatic selectivity up to 53.9%) and less marked in the case of standard ZSM-5 (up to 36.4%) and Beta zeolite (up to 35.0%). Mesostructured catalysts like Al-MCM-41 and Al-SBA-15 favoured the production of light C₂–C₅ hydrocarbons (up to 57.9%) while the formation of aromatic products was significantly lower than with zeolitic materials. The paper examines the extent and the causes for this product selectivity and discusses its connection with the acid and textural properties of each catalyst. It was also observed that, under the experimental conditions employed, the products generated were not significantly affected by the nature and origin of the polymers employed.     

利用根箱法解析水稻根际土壤中氮的行为

为研究水田土壤中氮的行为,施给15NH4 或15NO3-标记的硝胺(NH415NO3或15NH4NO3)的沙壤土(Shirasu soil)添充在根箱里,对Japonica水稻(品种Hinohikari)进行温室栽培6周.收割后,水稻植株分地上部和根部,对各自的全氮,15N atom％进行测定.根箱各区域的土壤按着鲜土形态进行采取后,对此全氮,NO3-N,水溶性NH4-N,KCl抽出NH4-N和其各自的15N atom％进行测定.研究结果表明,土壤全氮含量与栽培前相比,在非根际明显降低,但在根际比非根际要高,保持了与栽培前相同的水平.土壤NO3-N浓度从非根际到根际递增,但与其栽培前相比显著地降低,在整个根箱里,施给NO3-N的79％为因脱氮而损失.土壤中NO3-N的大部分来自于土壤氮化合物,来自施肥的比例却较低,尤其是在根际.反而,施给NO3-N的残存率约仅为16％左右,但其中有机态氮所占的比率在非根际里55％～86％,在根际却达到了93％.土壤水溶性NH4-N和KCl抽出NH4-N浓度靠近根际逐渐降低,而且在非根际两者匀由1∶10的比例存在,但在根际里水溶性NH4-N没被检索到.在非根际里,土壤KCl抽出NH4-N的35％～66％为来自施肥,但其比例在根际里却降到15％左右.在土壤中残存的来自施给NH4-N的氮化合物之中,有机态氮所占的比例在非根际里约为11％～65％,但在根际却达到了92％.以上结果表明,在水稻根际,氮的无机化和有机化的活性比非根际显著.     

Low-temperature (NO + O2) adsorption performance of alkaline earth metal-doped C-FDU-15

To improve the removal capacity of NO + O₂ effectively, the alkaline earth metal-doped order mesoporous carbon (A-C-FDU-15(0.001) (A = Mg, Ca, Sr and Ba)) and Mg-C-FDU-15(x) (x = 0.001?0.003) samples were prepared, and their physicochemical and NO + O₂ adsorption properties were determined by means of various techniques. The results show that the sequence in (NO + O₂) adsorption performance was as follows: Mg-C-FDU-15(0.001) (93.2 mg/g) > Ca-C-FDU-15(0.001) (82.2 mg/g) > Sr-C-FDU-15(0.001) (76.1 mg/g) > Ba-C-FDU-15(0.001) (72.9 mg/g) > C-FDU-15 (67.1 mg/g). Among all of the A-C-FDU-15(0.001) samples, Mg-C-FDU-15(0.001) possessed the highest (NO + O₂) adsorption capacity (106.2 mg/g). The species of alkaline earth metals and basic sites were important factors determining the adsorption of NO + O₂ on the A-C-FDU-15(x) samples, and (NO + O₂) adsorption on the samples was mainly chemical adsorption. Combined with the results of (NO + O₂)-temperature-programmed desorption ((NO + O₂)-TPD) and in situ diffused reflectance infrared Fourier transform spectroscopy (DRIFTS) characterization, we deduced that there were two main pathways of (NO + O₂) adsorption: one was first the conversion of NO and O₂ to NO₂ and then part of NO₂ was converted to NO₂^? and NO₃^?; and the other was the direct oxidation of NO to NO₂^? and NO₃^?.     

森林地区PM2.5中氨基酸的水平、来源及转化

在春季采集了南昌森林地区(28.75°N,115.71°E)大气PM_2.5样品,测定了其结合氨基酸(CAAs)和游离氨基酸(FAAs)的浓度以及甘氨酸(Gly)的氮同位素.结果表明,大气气溶胶中总CAAs的浓度为272.8~4761.5pmol/m³,总FAAs浓度为56.4~494.0pmol/m³.通过分析PM_2.5中氨基酸的百分比组成,得出CAAs中Pro、Gly、Glu、Leu和Ala为主要氨基酸,分别占总CAAs的(19.5±12.0)%, (19.4±10.6)%, (15.3±4.9)%, (12.8±5.4)%和(9.1±1.6)%.在FAAs中,Gly为最丰富的氨基酸,占总FAAs的(71.1±9.2)%,其他单个FAAs的百分比却很小(占比范围为0.1%~14.3%).FAAs中的中性氨基酸百分占比明显高于其在CAAs中的百分占比,这可能与远距离传输过程中氨基酸的光化学反应有关.通过氨基酸浓度与O₃、NO₂和温度的相关性分析,发现森林地区气溶胶中FAAs形成与大气光化学过程和热反应有关.气溶胶中δ¹⁵N_C-Gly值(-1.0‰~+17.5‰)和δ¹⁵N_F-Gly值(-5.5‰~+13.0‰)均接近于土壤源的δ¹⁵N_Gly值,说明森林地区PM_2.5中氨基酸可能主要来源于土壤源.