Optimization of micro-aeration intensity in acidogenic reactor of a two-phase anaerobic digester treating food waste

Micro-aeration is known to promote the activities of hydrolytic exo-enzymes and used as a strategy to improve the hydrolysis of particulate substrate. The effect of different micro-aeration rates, 0, 129, 258, and 387 L-air/kg TS/d (denoted as LBR-AN, LBR-6h, LBR-3h and LBR-2h, respectively) on the solubilization of food waste was evaluated at 35 °C in four leach bed reactors (LBR) coupled with methanogenic upflow anaerobic sludge blanket (UASB) reactor. Results indicate that the intensity of micro-aeration influenced the hydrolysis and methane yield. Adequate micro-aeration intensity in LBR-3h and LBR-2h significantly enhanced the carbohydrate and protein hydrolysis by 21–27% and 38–64% respectively. Due to the accelerated acidogenesis, more than 3-fold of acetic acid and butyric acid were produced in LBR-3h as compared to the anaerobic treatment LBR-AN resulting in the maximum methane yield of 0.27 L CH₄/g VS_added in the UASB. The performance of LBR-6h with inadequate aeration was similar to that of LBR-AN with a comparable hydrolysis degree. Nevertheless, higher aeration intensity in LBR-2h was also unfavorable for methane yield due to significant biomass generation and CO₂ respiration of up to 18.5% and 32.8% of the total soluble hydrolysate, respectively. To conclude, appropriate micro-aeration rate can promote the hydrolysis of solid organic waste and methane yield without undesirable carbon loss and an aeration intensity of 258 L-air/kg TS/d is recommended for acidogenic LBR treating food waste.     

Enterotoxin production and antimicrobial susceptibility in Staphylococci isolated from traditional raw milk cheeses in Serbia

This study was undertaken to determine the prevalence of coagulase positive staphylococci (CPS) by examining a total of 71 raw milk cheeses. Additionally, enterotoxigenicity, antimicrobial susceptibility and the presence of mecA and mecC genes in the staphylococcal isolates were investigated. The isolation and enumeration procedure of CPS followed the International Organization for Standardization (ISO) standard. The presumptive staphylococci were identified by matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS) using the VITEK MS system. VIDAS® Staph enterotoxin II assay was used for the detection of classical enterotoxins. Antimicrobial susceptibility testing (AST) was accomplished performing the disk diffusion method. All suspected methicillin resistant staphylococci were investigated for the presence of mecA and mecC genes by PCR assay. A high prevalence (87.32%) of CPS was detected in the cheeses at contamination levels up to 5.58 log CFU g^?1. Among 47 staphylococcal isolates screened for enterotoxin production, only one isolate, identified as S. hyicus, was confirmed as being enterotoxigenic. Resistance to penicillin (63.70%) was the most common resistance among the tested Staphylococcus aureus isolates. The dominant phenotypic resistance patterns in coagulase negative staphylococci (CNS) were resistance to ofloxacin and fusidic acid. All CNS isolates were susceptible to the clinically important antibiotics clindamycin, chloramphenicol, gentamicin, linezolid, rifampicin and trimethoprim-sulfamethoxazole. The mecA and mecC genes were not detected. To the best of our knowledge, this is the first study concerning evaluation of the presence of methicillin resistant staphylococci (MRS) in dairy products in Serbia.     

Evaluation of a recycling process for printed circuit board by physical separation and heat treatment

Printed circuit boards (PCBs) from discarded personal computer (PC) and hard disk drive were crushed by explosion in water or mechanical comminution in order to disintegrate the attached parts. More parts were stripped from PCB of PC, composed of epoxy resin; than from PCB of household appliance, composed of phenol resin.In an attempt to raise the copper grade of PCB by removing other components, a carbonization treatment was investigated. The crushed PCB without surface-mounted parts was carbonized under a nitrogen atmosphere at 873–1073 K. After screening, the char was classified by size into oversized pieces, undersized pieces and powder. The copper foil and glass fiber pieces were liberated and collected in undersized fraction. The copper foil was liberated easily from glass fiber by stamping treatment.As one of the mounted parts, the multi-layered ceramic capacitors (MLCCs), which contain nickel, were carbonized at 873 K. The magnetic separation is carried out at a lower magnetic field strength of 0.1 T and then at 0.8 T. In the +0.5 mm size fraction the nickel grade in magnetic product was increased from 0.16% to 6.7% and the nickel recovery is 74%.The other useful mounted parts are tantalum capacitors. The tantalum capacitors were collected from mounted parts. The tantalum-sintered bodies were separated from molded resins by heat treatment at 723–773 K in air atmosphere and screening of 0.5 mm. Silica was removed and 70% of tantalum grade was obtained after more than 823 K heating and separation.Next, the evaluation of Cu recycling in PCB is estimated. Energy consumption of new process increased and the treatment cost becomes 3 times higher comparing the conventional process, while the environmental burden of new process decreased comparing conventional process.The nickel recovery process in fine ground particles increased energy and energy cost comparing those of the conventional process. However, the environmental burden decreased than the conventional one.The process for recovering tantalum used more heat for the treatment and therefore the energy consumption increased by 50%, when comparing with conventional process. However, the market price for tantalum is very large; the profit for tantalum recovery is added. Also the environmental burden decreased by the recycling of tantalum recovery. Therefore, the tantalum recovery is very important step in the PCB recycling. If there is no tantalum, the consumed energy and treatment cost increase in the new process, though the environmental burden decreases.     

Shifts in microbial community structure and diversity in a MBR combined with worm reactors treating synthetic wastewater

The chemical oxygen demand (COD) and NH₃-N removal, membrane fouling, sludge characteristics and microbial community structure in a membrane bioreactor (MBR) coupled with worm reactors (SSBWR) were evaluated for 210 days. The obtained results were compared to those from a conventional MBR (C-MBR) operated in parallel. The results indicated that the combined MBR (S-MBR) achieved higher COD and NH₃-N removal efficiency, slower increase in membrane fouling, better sludge settleability and higher activities of the related enzymes in the activated sludge. Denaturing gradient gel electrophoresis was used to analyze the microbial community structures in the C-MBR and the S-MBR. The microbial community structure in the S-MBR was more diverse than that in the C-MBR. Additionally, the slow-growing microbes such as Saprospiraceae, Actinomyces, Frankia, Clostridium, Comamonas, Pseudomonas, Dechloromonas and Flavobacterium were enriched in the S-MBR, further accounting for the sludge reduction, membrane fouling alleviation and wastewater treatment.     

Performance and microbial community of a membrane bioreactor system——Treating wastewater from ethanol fermentation of food waste

In this study, a lab-scale biological anaerobic/anaerobic/anoxic/membrane bioreactor(A_-~3MBR) was designed to treat wastewater from the ethanol fermentation of food waste,a promising way for the disposal of food waste and reclamation of resources. The 454 pyrosequencing technique was used to investigate the composition of the microbial community in the treatment system. The system yielded a stable effluent concentration of chemical oxygen demand(202 ± 23 mg/L), total nitrogen(62.1 ± 7.1 mg/L), ammonia(0.3 ±0.13 mg/L) and total phosphorus(8.3 ± 0.9 mg/L), and the reactors played different roles in specific pollutant removal. The exploration of the microbial community in the system revealed that:(1) the microbial diversity of anaerobic reactors A_1 and A_2, in which organic pollutants were massively degraded, was much higher than that in anoxic A_3 and aerobic MBR;(2) although the community composition in each reactor was quite different, bacteria assigned to the classes Clostridia, Bacteroidia, and Synergistia were important and common microorganisms for organic pollutant degradation in the anaerobic units, and bacteria from Alphaproteobacteria and Betaproteobacteria were the dominant microbial population in A_3 and MBR;(3) the taxon identification indicated that Arcobacter in the anaerobic reactors and Thauera in the anoxic reactor were two representative genera in the biological process. Our results proved that the biological A_-~3MBR process is an alternative technique for treating wastewater from food waste.     

Effect of oxide nanoparticles on the morphology and fluidity of phospholipid membranes and the role of hydrogen bonds

Engineered oxide nanoparticles (NPs) are widely applied in insulators, catalyzers, paints, cosmetic products, textiles and semiconductors. Their attachment on cell membrane may lead to cytotoxicity. The effects of Al₂O₃, Fe₂O₃, SiO₂, TiO₂ and ZnO NPs on membrane integrity and fluidity were studied using giant or small unilamellar vesicles in this study. Al₂O₃ and SiO₂ NPs disrupted the oppositely charged membrane, indicating the important role of electrostatic attraction. However, Fe₂O₃, TiO₂ and ZnO NPs did not cause serious membrane disruption as Al₂O₃ and SiO₂ NPs. Membrane fluidity was evaluated by the generalized polarity (GP) values of Laurdan fluorescent emission. SiO₂ NPs induce the membrane gelation of both positively and negatively charged membrane. Al₂O₃ and ZnO NPs induced the gelation of the oppositely charged membrane, but did not cause obvious membrane gelation to the like charged membrane. The phospholipid molecular structural changes after NP exposure were analyzed by Fourier transform infrared (FT-IR) spectroscopy. FT-IR spectra revealed the hydrogen bond formation between NPs and the carbonyl/phosphate groups of phospholipids. Al₂O₃ and SiO₂ NPs showed strongest evidence of hydrogen bonding on their FT-IR spectra. It was consistent with the microscopic observation and fluorescent data that Al₂O₃ and SiO₂ NPs caused more serious membrane disruption and gelation. This study on membrane damage provides further knowledge on the cytotoxicity of nanomaterials and the safety of NP application.     

Assessment of the clear-sky bias issue using continuous PM10 data from two AERONET sites in Korea

A bias in clear-sky conditions that will be involved in estimating particulate matter(PM)concentration from aerosol optical depth(AOD) was examined using PM_(10) from two Aerosol Robotic Network sites in Korea. The study periods were between 2004 and 2007 at Anmyon and between 2003 and 2011 at Gosan, when both PM_(10) and AOD were available. Mean PM_(10) when AOD was available(PM AOD) was higher than that from all PM_(10)data(PM all) by 5.1 and9.9 μg/m~3 at Anmyon and Gosan, which accounted for 11% and 26% of PM all, respectively.Because of a difference between mean PM_(10) under daytime clear-sky conditions(PM clear)and PM AOD, the variations in ΔPM_(10), the difference of PM all from PM clear rather than from PM AOD, were investigated. Although monthly variations in ΔPM_(10)at the two sites were different, they were positively correlated to those in ΔT, similarly defined as ΔPM_(10)except for temperature, at both sites. ΔPM_(10)at Anmyon decreased to a negative value in January due to an influence of the Siberian continental high-pressure system while ΔPM_(10)at Gosan was high in winter due to an effect of photochemical production at higher temperatures than at Anmyon.     

北京市郊区夏季臭氧重污染特征及生成效率

为研究北京郊区夏季O₃(臭氧)重污染过程特征及O₃生成的光化学敏感性,基于2016年夏季在北京郊区开展的针对O₃及其相关污染物的强化观测试验(7月23日—8月31日,共计40 d),分析了观测期间O₃浓度[以φ(O₃)计]变化特征、O₃重污染过程主控因素与O₃敏感性化学特征.结果表明:观测期间φ(O₃)超标时有发生,最大小时φ(O₃)为151.1×10-9,其中有15 d的φ(O₃)最大8 h滑动平均值(O₃-max-8h)超过了GB 3095—2012《环境空气质量标准》二级标准限值,占观测天数的37.5%;不同O₃重污染过程成因有所不同,城市烟羽传输的污染物对郊区O₃重污染过程影响显著(观测期间臭氧重污染过程:过程1,7月27—29日;过程3,8月9—11日;过程4,8月16日;过程5,8月21—24日),区域光化学污染对郊区O₃重污染过程也有贡献(观测期间O₃重污染过程2:8月4—6日);结合后向气流轨迹进一步辅助说明了不同重污染过程中O₃的来源不同.研究还发现,观测区域存在反“周末效应”现象,说明观测区域周末受人为影响较为明显;基于观测数据计算的OPE(O₃生成效率)分析了O₃光化学敏感性表明,在有OPE值的22 d内NO_x控制区和VOCs控制区出现的概率(41%)相等,即观测区域O₃对NO_x和VOCs均敏感;此外还发现,在O₃重污染过程中光化学敏感性会随其反应进程发生改变,由NO_x控制区逐渐转变为VOCs控制区.      

生活垃圾焚烧飞灰固化体力学及重金属浸出特性

以苏州七子山生活垃圾焚烧厂产生的飞灰为研究对象,采用水泥作为固化剂,研究水泥飞灰固化体的应力应变特征及重金属浸出特性,并探讨了水泥飞灰配合比、养护时间等关键性因素对这些特性的影响。实验结果表明:较养护3 d的样品,其余养护时间的样品强度平均增长了约96.2%,而其破坏应变平均减小了56%。随着水泥含量和养护时间的增加,飞灰固化体的强度上升,而其破坏应变减小,该趋势主要归因于钙矾石(AFt)的形成促进了飞灰固化体强度的发展。较飞灰原样,飞灰固化体的重金属浸出浓度随着水泥含量、养护时间的增加而降低了38%~99%,重金属的迁移被限制,主要归因于水化硅酸钙(C—S—H)和钙矾石(AFt)的形成,以及飞灰和水泥水化反应创造的强碱性环境。     

厌氧发酵处理庆大霉素菌渣的可行性及条件优化

采用厌氧发酵处理庆大霉素菌渣,考察了含固率、接种比、接种污泥、发酵底物等因素对庆大霉素菌渣厌氧发酵的影响,并用累积净甲烷产量衡量庆大霉素菌渣进行厌氧发酵的可行性及发酵程度。试验结果证实了庆大霉素菌渣进行厌氧发酵的可行性,其中含固率和接种比对发酵的影响较大,最佳条件为含固率5%,接种比1/3;对比试验所用3种接种污泥,发现接种某造纸厂污水处理IC反应器的厌氧颗粒污泥效果最优,在最优含固率和接种比的条件下,累积净产甲烷量为28.21 m3/t;此外,试验还证实,采用不同菌渣的联合发酵表现出了明显的协同作用,在最优条件下,庆大霉素菌渣与林可霉素菌渣按1∶2的比例联合发酵的产甲烷量可达到37.5 m3/t。