基于火探管式的锂离子电池灭火技术研究

为研究锂离子电池灭火方案,基于火探管灭火技术同时利用新型清洁灭火剂Novec 1230,组装成火探管灭火系统。在灭火测试平台上以功率为200 W的电热管作为外热源引发单电池或电池模组热失控,通过改变火探管的布置位置,记录相应的灭火行为以及灭火效率,并对实验结果进行了分析。研究结果表明,当火探管灭火系统直接布置在电池正上方时,在起火后的5.6s内控制火情;随着灭火剂用量增加可以显著降低体系温度,防止电池复燃以及连锁热失控现象发生;火探管有效覆盖区域外的失控电池作为热源将继续加热临近电池,引发连锁热失控,造成灭火系统失效;根据电池热失控后的燃烧行为以及传热行为,提出相应的火探管灭火系统复合方案。     

苯胺-邻氨基酚共聚物对水中Hg(Ⅱ)吸附性能的研究

利用化学氧化法合成了苯胺-邻氨基苯酚的共聚物,并通过静态实验研究了材料对水中汞离子的吸附性能。研究结果表明,该共聚物对废水中汞离子有优异的去除效果,其吸附容量可达212.13 mg/g;吸附等温线符合Langmu ir单层吸附模型,动力学过程符合准二级动力学模型;溶液pH值对吸附影响不是很大,pH 5~10范围都有较好的吸附效果;氯离子易与汞离子形成水溶性更强的络合物,对共聚物的吸附有很大的抑制作用。     

4A沸石去除水中Pb2＋的研究

在静态条件下,研究了4A沸石对废水中Pb2＋的吸附性能,并探讨了影响吸附的因素。实验表明：当温度为30℃,废水pH为5～6,0．01g4A沸石对100mg／LPb2＋溶液10mL吸附20min,Pb2＋的去除率可达到99％以上。在实验研究条件下,4A沸石对Pb2＋的吸附符合Langmuir和Freundlich等温吸附方程,相关系数为0．9819和0．9998。经计算,4A沸石对Pb2＋的饱和吸附量为125mg／g。4A沸石吸附水中Pb2＋达到吸附平衡的时间较短;溶液pH值的变化对吸附效果影响不显著;温度从室温略微升高,Pb2＋的去除率略有增大。吸附在4A沸石上的Pb“可回收利用,处理后的4A沸石可以再生,且重复使用性能较好。     

新型硅镁胶(MgO·2SiO_2)对模拟放射性废水中Co~(2+)的吸附性能

以泡花碱和氯化镁为原料合成出了一种新型硅镁胶(MgO·2SiO2)吸附材料,用傅里叶红外光谱仪对其进行了表征,并对模拟放射性废水中的Co2+进行吸附实验。结果表明,控制合成pH在10.50~11.00,可以得到目标硅镁胶(MgO·2SiO2),在460 cm-1处出现了较强的吸收峰,这是由Mg—O伸缩振动和Si—Mg—O弯曲振动引起。在500℃焙烧4h后,可以得到吸附性能良好的硅镁胶,随着溶液pH的升高,去除率增大,在pH为4~8时达到最大。25℃时,最大吸附量可达135.5 mg/g,吸附过程符合Langmuir等温吸附方程和准二级动力学方程。重复使用4次,对Co2+的吸附量仍然达到130 mg/g,说明硅镁胶是一种可重复利用的吸附剂。     

膜电解技术处理含氯及重金属的废酸

采用离子交换膜电解技术处理铜冶炼过程产生的含氯及重金属的废酸。考察了废酸处理工艺、电解温度、电解时间、电流密度和催化剂的添加等条件对处理效果的影响。实验结果表明：采用先沉淀重金属后脱氯的废酸处理工艺,氯离子和铜离子的去除效果均较好;当以钛盐为催化剂时,在电解温度为40 ℃、电解时间为2.0 h、电流密度为825 A/m²的最佳工艺条件下,处理后废酸中的氯离子质量浓度为0.22 g/L,氯离子去除率为98.59%,铜离子质量浓度为0.45 g/L,铜离子去除率为95.08%,其他重金属大部分也得到有效去除。净化后的废酸可回用至铜冶炼的生产过程中。     

表面活性剂改性4A分子筛对Cr(VI)的吸附行为

采用浸渍法对4A分子筛进行表面改性,通过引入阳离子表面活性剂,使4A分子筛表面附着季铵型阳离子,并与反离子Br-形成"阴离子交换膜",从而促使更多的Cr(VI)阴离子通过离子交换吸附到改性4A分子筛上,通过X-射线衍射(XRD)和傅里叶变换红外光谱(FTIR)对样品的物相结构和组成进行表征分析。研究表明,表面活性剂的类型和疏水碳氢链结构会影响4A分子筛的吸附能力,十八烷基三甲基溴化铵(OTAB)碳氢链长,在分子筛表面形成的双分子层密,对Cr(VI)的吸附量最大。采用准一级、准二级、Elovich和Bangham动力学模型对六价铬的吸附数据进行拟合,其中准一级动力学方程最符合十八烷基三甲基溴化铵改性分子筛的吸附行为。同时,分别从Langmuir和Redlich-Peterson等温吸附模型获得六价铬的最大吸附量为13.98 mg/g,且改性分子筛以均一表面吸附为主。     

Development of a hybrid microbial fuel cell (MFC) and fuel cell (FC) system for improved cathodic efficiency and sustainability: the M2FC reactor

In an effort to improve the efficiency and sustainability of microbial fuel cell (MFC) technology, a novel MFC reactor, the M2FC, was constructed by combining a ferric-based MFC with a ferrous-based fuel cell (FC). In this M2FC reactor, ferric ion, the catholyte in the MFC component, is regenerated by the FC system with the generation of additional electricity. When the MFC component was operated separately, the electricity generation was maintained for only 98 h due to the depletion of ferric ion in the catholyte. In combination with the fuel cell, however, the production of power was sustained because ferric ion was continually replenished from ferrous ion in the FC component. Moreover, the regeneration process of ferric ion by the FC produced additional energy. The M2FC reactor yielded a power density of up to 2 W m⁻² (or time-averaged value of approximately 650 mW m⁻²), density up to 20 times (or approximately six times based on time-averaged value) higher than the corresponding MFC system.     

Novel mesoporous microspheres of Al and Ni doped LMO spinels and their performance as cathodes in secondary lithium ion batteries

A facile, scalable, and solution-based technique is used to fabricate Al and Ni-doped (LiAl_0.1Mn_1.9O₄ and LiAl_0.1Ni_0.1Mn_1.8O₄) microspheres of lithium manganese oxide (LMO) spinels for use as reversible cathode materials for lithium ion batteries (LIBs). The spheres of the two samples exhibit different porosities. Cells with these LMO-based cathodes are then cycled between 4.5 V and 2 V to study their stabilities while simultaneously being subjected to the undesirable Jahn-Teller distortion that occurs around the ~3 V regime. The LiAl_0.1Mn_1.9O₄ (LAMO) and the LiAl_0.1Ni_0.1Mn_1.8O₄ (LANMO) cells exhibit comparable open circuit voltages (OCV) of 2.94 V and 2.97 V, respectively. During cell cycling, the LAMO cell exhibits a maximum specific capacity of 122.51 mAh g^?1 with a capacity fade of 65.35% after 75 cycles. The LiAl_0.1Ni_0.1Mn_1.8O₄ (LAMO) sample fares better and exhibits a maximum of 140.49 mAh g^?1 and a capacity drop of 52.59%. Detailed structural studies indicate that Ni doping and the greater degree of porosity of the LANMO sample to be a stabilizing factor. This is further confirmed by cyclic voltammetry (CV) and AC impedance spectra analysis.     

碱激发胶凝材料及其固化Pb^2＋的试验研究

对碱激胶凝材料（碱-偏高岭土、碱-矿渣和碱-粉煤灰）与水-水泥体系固化Ph^2＋进行了试验研究,其中水-水泥体系为对比样。结果表明：对于相同稠度的碱激发胶凝材料,即使Pb^2＋含量达到2．4％,除了碱-粉煤灰的抗压强度略低外,其他都达到30MPa以上,满足填埋或做建筑基材的使用要求;与水泥相比,碱激发胶凝材料能显著降低重金属离子（Ph^2＋）浸出浓度,其规律性与其NH4交换容量大小的规律性一致,与其固化体的抗压强度的大小没有相关性。     

Changes in negative air ions concentration under different light intensities and development of a model to relate light intensity to directional change

The purpose of this research was to determine changes in negative air ion (NAI) concentrations produced by plants grown under different light intensities. NAI concentrations were observed and analyzed in an outdoor green space with five plant species (Aloe arborescens, Clivia miniata, Chlorophytum comosum, Opuntia brunnescens, Crassula portulacea) and A. arborescens was then grown under controlled-light conditions in an enclosed space for the subsequent light intensity experiment.