Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets

A modified method of severe plastic deformation (SPD) entitled constrained groove pressing-cross route (CGP-CR) was introduced for imposing a high magnitude of equivalent strain of about 2.32 per pass on the sheet form samples. The major benefit of this improved route compared to previous common route was the more homogeneity of strain in the rolling (RD) and transverse (TD) directions of sheets. In this study, low carbon steel samples were used for examination of evolutions in microstructure and mechanical properties during SPD via CGP-CR process. Mechanical properties improvement were measured by tensile and macro hardness tests. The results indicate that CGP-CR process can effectively improve tensile strength; and also, yield stress and hardness of as-received low carbon steel samples were improved up to about 100% after two deformation passes. Also, high magnitude of inhomogeneity can be observed in hardness distribution through first pass of the process which diminishes in the subsequent passes. Microstructural evolutions during process were monitored by optical microscopy observations and X-ray diffraction analysis. The results demonstrate that initial ferritic microstructure with grain size of about 30 μm was refined to a 225 nm cell structure after two passes of CGP-CR process.     

Modulation-assisted high speed machining of compacted graphite iron (CGI)

The application of controlled, low-frequency modulation (～100 Hz) superimposed onto the cutting process in the feed-direction – modulation-assisted machining (MAM) – is shown to be quite effective in reducing the wear of cubic boron nitride (CBN) tools when machining compacted graphite iron (CGI) at high machining speeds (>500 m/min). The tool life is at least 20 times greater than in conventional machining. This significant reduction in wear is a consequence of the multiple effects realized by MAM, including periodic disruption of the tool–workpiece contact, formation of discrete chips, enhanced fluid action and lower cutting temperatures. The propensity for thermochemical wear of CBN, the principal wear mode at high speeds in CGI machining, is thus reduced. The tool wear in MAM is also found to be smaller at the higher cutting speeds (730 m/min) tested. The feed-direction MAM appears feasible for implementation in industrial machining applications involving high speeds.     

企业环境管理中政府和企业作用分析

我国的经济发展伴随着日益严重的环境问题。在引起环境问题的诸多因素中,来自企业方面的因素对环境的影响最为深远,因此改善环境首先就需要加强企业的环境管理。在推动企业进行环境管理的各种因素中,既有如政府的管制等外部因素,也有如减少成本、产品差异化等企业自身内部因素。外部因素和内部因素对推动企业环境管理都具有重要作用,但也有其局限性。本文通过政府管制及企业自身因素对驱动企业进行环境管理的作用机制的研究,分析各个驱动因素优缺点,寻求各驱动因素的最佳的组合,促使企业更好地加强环境管理。     

在用车I／M制度的脆性及脆性源研究

I／M制度作为一个系统存在着脆性源,如果该制度在运行过程中控制不好脆性源,则其有效实施将受到影响。利用系统脆性理论对该制度进行分析研究找出L／M制度系统的脆性源以及解决措施是其分析研究的目的。在系统子因子中从业人员素质、仪器设备是最大的脆性源,但是其均被维修企业和检测企业所包含。综合分析研究结果显示,由于其在维修企业的脆性度比在检测企业的脆性度大,所以维修企业是该制度最重要的脆性源。用系统脆性理论分析方法分析I／M制度的脆性是一种科学、有效和实用的方法,具有较好的应用前景,为保障更好的运行I／M制度以有效的控制在用车的排放提供了理论依据。     

土地利用变化对土壤硝化及氨氧化细菌区系的影响

以西藏高原相邻的原始森林、天然草原和农田土壤为研究对象,分别采用室内培养法和nested PCR-DGGE技术,对比研究了这3个生态系统的土壤硝化势、硝态氮浓度以及土壤氨氧化细菌（AOB）菌群区系.结果表明,农田土壤的硝化势和硝态氮（NO 3--N）浓度显著高于相邻的草原和森林土壤,硝化势分别是森林和草原土壤的9倍和11倍,NO 3--N是农田土壤无机氮（Nmin）的主要成分,占无机氮的70%～90%.铵态氮（NH 4＋-N）则是森林和草原土壤中主要的无机氮形态.原始森林和天然草原间的硝化势和硝态氮浓度没有显著差异.原始森林的土壤AOB菌群数量、多样性及均匀度最低.天然草原生态系统转换为农田后,土壤AOB菌群的多样性和均匀度显著降低,但是农田土壤的AOB菌群结构仍与其前身草原生态系统有较高的相似性.原始森林的AOB菌群数量、多样性及均匀度最低直接导致了其硝化势最低;农田土壤的硝化势和硝态氮浓度最高意味着农田生态系统中优势AOB的活性最高.以上结果表明,土地利用变化导致土壤氮素内循环及其关键微生物AOB的多样性与活性均发生显著变化,这些变化会影响土壤环境质量以及生态系统的持续与稳定.     

不同TS浓度互花米草沼渣二次发酵特性研究

中温（35±1）℃条件下,沼渣经6%的NaOH常温下处理48 h后,在TS含量8%、10%、12%的条件下沼气发酵.分析了发酵过程中日产气量、累积产气量、甲烷含量、pH值、挥发性脂肪酸（VFA）的变化,从不同角度考察TS含量负荷对沼渣二次发酵特性的影响.单位TS的日产气高峰分别达10、14、13 mL.g-1,累积产气率为217、227、228 mL.g-1,甲烷含量均在65%以上.发酵过程中最低pH为7.04.乙酸浓度最高分别为3 364、3 286、5 728 mg.L-1,丙酸和丁酸浓度均低于1 100 mg.L-1.结果表明,沼渣为难降解有机物,分解缓慢,不易出现酸化现象,但仍具有较强的产气潜力.