管理措施对农田生态系统土壤呼吸的影响

为研究管理措施(氮肥施用和耕翻措施)对农田土壤呼吸的影响,采用静态暗箱-气相色谱法对农田生态系统的土壤呼吸作用进行了5个生长季(2002~2003年小麦,2003年玉米、大豆,2003~2004年小麦,2004年玉米,2004~2005年小麦)的野外观测试验.结果表明,冬小麦基肥(2002-11-09)、返青肥(2003-02-14)和拔节肥(2003-03-26)施用后2周内氮肥施用处理的土壤呼吸速率明显高于对照,但不同施氮水平间的土壤呼吸速率无显著差异.耕翻对土壤呼吸的影响效应受到前茬作物类型的制约.在2003~2004年的冬小麦生长季(其前茬种植的作物为水稻),不耕和浅耕处理的平均土壤呼吸速率之间无显著差异(p>0.05).在2004年玉米生长季浅耕比不耕处理显著增加了土壤呼吸速率(p<0.05),而在后茬的2004~2005年小麦生长季浅耕比不耕又显著降低了土壤呼吸速率(p<0.05).在前茬作物为水稻的麦田(2004~2005年小麦生长季),深耕比不耕处理显著增加了土壤CO2排放量.不同管理措施下,农田土壤呼吸与土壤温度的关系均可用指数方程描述,针对不同管理措施下拟合得到的指数方程求得的Q10值在1...     

生物菌剂对石油污染土壤生物修复作用的研究

在实验室条件下,研究了生物菌剂的投加量、投加方式及环境温度对石油污染土壤的修复作用 结果表明,土壤中石油烃的降解效果与生物菌剂的投加量呈正相关,当生物菌剂投加量为0.6mg·kg^-1时,修复,48 d 后,石油烃的降解率为87%.GC-MS分析结果表明,石油污染原土中烷烃的含量最高为82.1%其次为烯烃,含量为16%,还含有少量的胡萝卜烷、烷基萘、甾烷和藿烷% 添加生物菌剂修复40 d 后,峰的数量由32个减少为14个,表明异构烷烃、烯烃、胡萝卜烷全部被降解,残留的物质为较难降解的正构烷烃、藿烷和甾烷,呈现前高后低的峰形,即接种细菌优先降解高碳组分,将长链的烷烃降解为短链的烷烃,随着生物菌剂投加量的增加,土壤中残留石油烃的含量逐渐降低% 一次加入生物菌剂修复,48 d后的峰高明显低于分2 次加入的相应值,故一次性全部加入生物菌剂是最佳的投加方式% 温度是限制石油污染土壤生物修复的重要环境因素,当温度为30℃第,48 d 的降解率可达80%,当温度为20℃,第,48 d的降解率可达60%,温度高有利于土壤中石油烃的降解,加快修复     

固定化微生物技术处理城市微污染河水研究

将陶粒、功能化聚氨酯泡沫(FPUFS)、阿科蔓柔性填料、人工水草等4种不同载体与高效复合菌剂BP35应用于曝气生物滤池(BAF)构成固定化曝气生物滤池(G-BAF),研究固定化微生物技术对城市微污染河水的净化效果.4种G-BAF对NH4+-N、叶绿素和浊度的去除率分别为83.0%~89.0%、77.5%~89.0%和84.4%~95.2%,均大于对COD、UV254和TP的去除效果.FPUFS含有羟基、环氧基和酰胺基等反应性基团,对酶和微生物的负载量大,因此FPUFS-G-BAF对污染物的去除效率高于其余3种G-BAF.水力停留时间(HRT)对4种G-BAF去除NH4+-N的影响均不显著,而对COD的去除效果影响较大.当溶解氧(DO)浓度由2 mg/L升至4 mg/L时,4种G-BAF对COD和NH4+-N的去除率分别提高了11.9%~18.0%和12.7%~16.1%.GC-MS分析结果表明,G-BAF工艺能有效地将河水中分子质量较大的难降解有机物降解为小分子物质.     

水淬渣人工湿地强化除磷作用研究

研究了水淬渣的磷吸附-解吸效果,构建了以水淬渣为主要基质的模拟垂直流人工湿地系统,分析了水力停留时间(HRT)和污染负荷变化对污水中磷去除的影响,探讨了湿地上行、下行流单元各层基质的除磷贡献.结果表明,水淬渣基质的磷饱和吸附量为3 333 mg.kg-1,其水溶性钙含量为0.084%,pH值为7.54,适合作为湿地除磷基质.HRT与磷除去率呈正相关,当HRT从1 d缩短为0.5 d时,TP去除率降低5.9%~4.7%,当HRT从2 d缩短为1 d时,TP去除率降低2.4%~4.7%,HRT为1 d条件下,水淬渣湿地的磷去除率>85%,说明无限延长HRT无益于强化除磷,适宜的HRT为1 d.在进水浓度稳定的条件下,进水污染负荷与磷去除率呈负相关,当污染负荷范围在12.2~36.8 g.(m2.d)-1时,水淬渣湿地的磷除去率可维持在85%,当污染负荷达到48.9 g.(m2.d)-1后,水淬渣湿地的磷除去率下降至65%,当污染负荷<36.8 g.(m2.d)-1时,水淬渣湿地的磷去除率>82%,说明高污染负荷可抑制基质表面及孔隙中Ca、Al等吸附磷的活跃位点,适宜的进水污染负荷为24.5~36.8g.(m2.d...     

崇明东滩海三棱藨草生物硅分布及季节变化

利用Na2CO3连续提取法,分析了崇明东滩海三棱藨草(Scirpus mariqueter)体内生物硅(BSi)含量与分布特征.结果表明,BSi在海三棱藨草体内的分布存在明显的季节变化差异,在生物体中连续积累是BSi的一个主要特征.地上部分BSi含量变化范围为0.26% ~ 0.93%,地下部分为0.31% ~ 0.92%,果实中则为0.24% ~0.43%.地上部分含量明显高于其他部分,说明BSi主要沉积在蒸发强烈的叶片中,植株个体生长阶段是决定地上部分BSi含量的主要因素.统计分析显示,根际沉积物BSi和植物各器官BSi相关性均显著,说明海三棱藨草依从主动吸硅机制,从根际沉积物获取所需的Si.地上、地下部分BSi含量与有机氮(ON)、C/N、土壤温度、植株高度也存在明显的相关性.     

电子产品环境应力筛选试验

为了使环境应力筛选试验在有效提高电子产品的可靠性方面得以广泛应用,介绍了环境应力筛选试验的概念,针对电子产品,论述了环境应力筛选典型应力参数的确定方法、加电检测的原则、筛选度和故障率的计算、筛选中暴露的典型缺陷等。提出了环境应力筛选试验的一般程序和一些需注意的问题。     

Evaluation of multiple reactions in dilute benzoyl peroxide concentrations with additives using calorimetric technology

Benzoyl peroxide (BPO) is a typical organic peroxide widely used in food processing, particularly flour bleaching. Due to the unstable nature of the oxygen-oxygen bond in BPO, it readily reacts under even mid-low-temperature conditions. Lower concentrations of BPO are also potentially explosive, even when combined with acid or alkaline additives. Given the history of both potential and documented industrial accidents, this study investigates the thermal stability of various BPO concentrations when mixed with acid or alkaline solutions. In addition, differential and integral kinetic models were applied to verify that the apparent activation energy data from the differential scanning calorimetry experiments were valid. The results of autocatalysis reactions and nth-order reaction simulations presented characteristics consistent with the experimental findings. The findings in this paper can be used as a reference for BPO products that are mediated with either an acid or an alkaline solution during production, storage, transportation, or use.     

Inhibiting effects by Fe2O3 on combustion and explosion characteristics of ABS resin

The global increase in the use of, and reliance on, plastics has prompted the demand for acrylonitrile-butadiene-styrene (ABS) resin in various fields. With this increased requirement, numerous failures have occurred in the ABS process. Those incidents, resulting from electrostatic discharge, powder accumulation, heat accumulation, construction sparks, and plant fires, have caused dust fire and explosions.In this study, the ABS resin was gleaned from the site and tested for its explosion parameters, including minimum ignition temperature of dust cloud (MIT_C), minimum ignition energy (MIE), and minimum explosion concentration (MEC). To improve loss prevention in the manufacturing process, ferric oxide (Fe₂O₃) as an inert additive was added in the ABS powder. According to the MIE test, Fe₂O₃ has an apparent inhibiting effect on dust explosion for the ABS dust. With the proportion of Fe₂O₃ increased from 25 to 50 mass% in ABS, the MIE increased from 67 to 540 mJ. The explosion tests via 20-L apparatus indicated that Fe₂O₃ mixed with ABS could not increase the MEC significantly. However, the explosion pressure dropped by increasing in the ratio of Fe₂O₃ in ABS. This inerting strategy of ABS was deemed to substantially lessen the probability and severity of fire and explosion.     

Experimental study on the competing effect of ceramic pellets on premixed methane-air flame propagation in a duct

It is urgent to explore effective suppression methods for gas fires and explosions to ensure the safe utilizations of combustible gases in industrial processes. In this work, experiments are performed to study the effect of spherical ceramic pellets on premixed methane-air flame propagation in a closed duct. High-speed schlieren photography and pressure transducers are used to record the flame propagation and pressure transient, respectively. Behaviors of the flame propagating through a section of the duct filled with ceramic pellets in mixtures at different equivalence ratios are scrutinized. Three different diameters of pellets are considered in the experiments. The result shows that the flame can be quenched in the case with a smaller pellet diameter (3 mm) for a wide range of equivalence ratios from fuel-lean to fuel-rich mixture. For larger pellet diameter (5 or 10 mm), flame extinction occurs in fuel-rich mixtures (e.g. Φ = 1.1, 1.2). For the cases of flame surviving through the pellets bed, the pellets show a significant influence on the flame structure and behavior. The flame propagation depends on the porosity and the mean void diameter of the porous media in the pellets bed. Small void diameter is beneficial to flame quenching, while large porosity can accelerate the flame propagation. The pressure dynamics evolution is closely related to the interaction of flame with the pellets, and it depends on whether the flame quenches in the pellets bed. Overall, d = 3 mm ceramic pellets display the best suppression effect on flame propagation and pressure buildup in this study. The results of this study are of great significance to guide the safety design of spherical suppression materials in engineering applications for process safety researchers and engineers.     

Thermal hazard and decomposition kinetics of 1-butyl-2,3-dimethylimidazolium nitrate via TGA/DSC and FTIR

1-Butyl-2,3-dimethylimidazolium nitrate ([Bmmim][NO₃]), a kind of versatile and novel ionic liquids, is widely applied in the modern petrochemical industry. Nevertheless, its thermal hazard safety data at high temperature or thermal disturbance conditions are currently unavailable. Therefore, this study aimed to characterize the thermal risk of [Bmmim][NO₃] through auto-ignition temperature measurements, flash point analysis, thermal gravimetric analysis/differential scanning calorimetry (TGA/DSC), TGA-Fourier transform infrared spectroscopy (TGA-FTIR) and thermal decomposition kinetics analysis. Additionally, [Bmmim][NO₃] was examined using isothermal thermogravimetric analysis at different temperatures (220, 230, 240, 250, 260 and 270 °C). The experimental results show that the flash point of [Bmmim][NO₃] is 305.70 ± 9.30 °C and the auto-ignition temperature is 341.00 ± 21.60 °C with an ignition delay time of 8.6 s. In addition, using the nitrogen atmosphere TGA data to calculate the activation energy according to the Friedman, Kissinger and Flynn-Wall-Ozawa methods, roughly the same results were obtained. Finally, TGA-FTIR results show that [Bmmim][NO₃] produced acetylene, butane, butanol and carbon dioxide during the thermal decomposition process. This study could provide data support and some guidance for the thermal hazard assessment and safety control of [Bmmim][NO₃] during its use and storage.