生活垃圾焚烧炉烟气新标准可达性分析

对《生活垃圾焚烧污染控制标准》(GB 18485—2001)和《生活垃圾焚烧污染控制标准》(GB 18485—2014)中各项指标的排放限值作比较,并探讨了二噁英、重金属、酸性气体、烟尘、碳氧化物等烟气污染物的控制措施。结合2010—2014年浙江省部分生活垃圾焚烧厂"三同时"验收废气监测数据,对排放指标的达标情况作分析,结果表明,采用"3T+E"焚烧工艺+SNCR脱硝+半干法脱酸+活性炭喷射+布袋除尘器除尘的烟气污染控制技术,可以同时满足脱氮、脱酸、除尘,以及去除重金属和二噁英的要求。     

典型钢铁企业汞排放水平及排放特征研究

以某典型钢铁企业为研究对象,测定企业废气、废水、固废汞排放水平,并分析汞排放特征。研究表明,球团、烧结、高炉工艺废气排口烟尘中汞排放浓度和排放速率明显低于烟气;汞主要以气态形式排放,烧结工艺排口废气汞最高浓度分别是其他2个排口的7倍和3倍。球团、烧结、高炉、电炉四工艺环节中,烧结汞排放速率占四工艺汞排放速率总和的87%。半干法脱硫、氨法脱硫、石灰石石膏脱硫对废气中汞的去除效率分别为90.0%、78.7%和29.9%。企业废水排放未检出汞,脱硫产生固废汞含量明显高于除尘产生固废汞含量,脱硫灰汞含量是脱硫石膏的15倍。     

废水污染物排放总量控制监测技术路线及要求

从中国污染物宏观控制目标出发,阐述了中国实施废水污染物排放总量控制监测的技术路线、监测项目以及相关技术要求。对污染物排放总量控制监测分析方法的应用、采样及测流等有关技术问题,提出了见解。以１９９８年污染源调查统计资料为例,提出了污染物排放总量控制监测方案及有关监测质量的保证措施。     

过氯乙烯滤膜采样-酸消解-钼蓝光度法测定磷酸雾

建立了过氯乙烯滤膜采样 -酸消解 -钼蓝分光光度法测定磷化车间磷酸雾的监测方法。实验室模拟采样的捕集效率为 95 7%～ 99 1 %。单个实验室对含 5μg和 1 5μg样品进行多次测定 ,其相对标准差小于 5% ,样品加标回收率为 98 2 %～ 1 0 0 5% ,方法检测限为 0 0 0 7mg/m3。对标样测定 ,结果均在给定值范围内。用该法与等离子发射光谱法(ICP)对 5个样品进行比对测定 ,结果均令人满意。     

Policy implementation of the Republic Act (RA) No. 9003 in the Philippines: A case study of Cebu city

Municipal Solid Waste Management (MSWM) is considered to be one of the most serious environmental issues in the Philippines. The annual waste generation was estimated at 10.6 million tonnes in 2012 and this is expected to double in 2025. The Republic Act (RA) No. 9003, widely known as the Ecological Solid Waste Management Act of 2000, provides the required policy framework, institutional mechanisms and mandate to the Local Government Units (LGUs) to achieve 25% waste reduction target through establishing an integrated solid waste management plan based on the 3Rs (reduce, reuse and recycling). Although the initial impact of the LGUs is still very limited in implementing the national mandate, this article highlights the successful experiences of Cebu, the second largest city in the Philippines, in reducing its MSW generation by more than 30% in the past three years. This study also explores the implementation process, innovative actions taken by the Cebu City Government in implementing the national mandate at local level and identifies the factors that influence the policy implementation. The findings suggest that the impacts of the national mandate can be achieved if the LGUs have the high degree of political commitment, planning and development of effective local strategies in a collaborative manner to meet with local conditions, partnership building with other stakeholders, capacity development, adequate financing and incentives, and in the close monitoring and evaluation of performance.     

Preparation and performance of arsenate (V) adsorbents derived from concrete wastes

Solid adsorbent materials, prepared from waste cement powder and concrete sludge were assessed for removal of arsenic in the form of arsenic (As(V)) from water. All the materials exhibited arsenic removal capacity when added to distilled water containing 10–700 mg/L arsenic. The arsenic removal isotherms were expressed by the Langmuir type equations, and the highest removal capacity was observed for the adsorbent prepared from concrete sludge with heat treatment at 105 °C, the maximum removal capacity being 175 mg-As(V)/g. Based on changes in arsenic and calcium ion concentrations, and solution pH, the removal mechanism for arsenic was considered to involve the precipitation of calcium arsenate, Ca₃(AsO₄)₂. The enhanced removal of arsenic for the adsorbent prepared from concrete sludge with heat treatment was thought to reflect ion exchange by ettringite. The prepared adsorbents, derived from waste cement and concrete using simple procedures, may offer a cost effective approach for arsenic removal and clean-up of contaminated waters, especially in developing countries.     

A comparative assessment of waste incinerators in the UK

The uptake in Europe of Energy from Waste (EfW) incinerator plants has increased rapidly in recent years. In the UK, 25 municipal waste incinerators with energy recovery are now in operation; however, their waste supply chains and business practices vary significantly. With over a hundred more plant developments being considered it is important to establish best business practices for ensuring efficient environmental and operational performance. By reviewing the 25 plants we identify four suitable case study plants to compare technologies (moving grate, fluidised bed and rotary kiln), plant economics and operations. Using data collected from annual reports and through interviews and site visits we provide recommendations for improving the supply chain for waste incinerators and highlight the current issues and challenges faced by the industry. We find that plants using moving grate have a high availability of 87–92%. However, compared to the fluidised bed and rotary kiln, quantities of bottom ash and emissions of hydrogen chloride and carbon monoxide are high. The uptake of integrated recycling practices, combined heat and power, and post incineration non-ferrous metal collections needs to be increased among EfW incinerators in the UK. We conclude that one of the major difficulties encountered by waste facilities is the appropriate selection of technology, capacity, site, waste suppliers and heat consumers. This study will be of particular value to EfW plant developers, government authorities and researchers working within the sector of waste management.     

A preliminary investigation into the physical and chemical properties of biomass ashes used as aggregate fillers for bituminous mixtures

Fly and bottom ashes are the main by-products arising from the combustion of solid biomass. Since the production of energy from this source is increasing, the processing and disposal of the resulting ashes has become an environmental and economic issue. Such ashes are of interest as a construction material because they are composed of very fine particles similar to fillers normally employed in bituminous and cementitious mixtures. This research investigates the potential use of ash from biomass as filler in bituminous mixtures. The morphological, physical and chemical characteristics of 21 different ashes and two traditional fillers (calcium carbonate and “recovered” plant filler) were evaluated and discussed. Leaching tests, performed in order to quantify the release of pollutants, revealed that five ashes do not comply with the Italian environmental re-use limits. Experimental results show a wide range of values for almost all the investigated properties and a low correlation with biomass type in terms of origin and chemical composition. Furthermore, sieving and milling processes were found to improve the properties of the raw material in terms of grading and sample porosity. The effectiveness of these treatments and the low content of organic matter and harmful fines suggest that most of the biomass ashes investigated may be regarded as potential replacements for natural filler in bituminous mixtures.     

Municipal solid waste management: Identification and analysis of engineering indexes representing demand and costs generated in virtuous Italian communities

The definition and utilisation of engineering indexes in the field of Municipal Solid Waste Management (MSWM) is an issue of interest for technicians and scientists, which is widely discussed in literature. Specifically, the availability of consolidated engineering indexes is useful when new waste collection services are designed, along with when their performance is evaluated after a warm-up period. However, most published works in the field of MSWM complete their study with an analysis of isolated case studies. Conversely, decision makers require tools for information collection and exchange in order to trace the trends of these engineering indexes in large experiments. In this paper, common engineering indexes are presented and their values analysed in virtuous Italian communities, with the aim of contributing to the creation of a useful database whose data could be used during experiments, by indicating examples of MSWM demand profiles and the costs required to manage them.