响应面法优化厌氧上清液除磷的研究

在用铁盐对厌氧段富磷上清液进行化学磷沉淀以实现磷的回收和达标排放的SBR系统中,为了减少铁盐化学除磷残余物可能对生物处理系统的影响,采用Box-Benhnken中心组合试验原理和响应面分析法,选择Fe:P、混凝搅拌强度、絮凝搅拌强度、搅拌时间等为自变量,残余铁离子为响应值,研究自变量之间的交互作用,以期优化化学除磷条件.通过Design-Expert 8.0软件得到1个二次响应曲面模型.得出最佳除磷条件:Fe:P比为1.40:1,搅拌强度为275r/min,快速搅拌时间为30s,絮凝搅拌强度为60r/min,絮凝时间为18min,沉淀时间为20min.在此条件下,化学混凝后残余铁离子浓度为0.37mg/L,化学除磷率大于97.66%.     

模拟环境条件下δ-MnO_2氧化As(Ⅲ)的搅拌流动动力学特征

采用搅拌流动法研究了酸性水钠锰矿及水羟锰矿2种δ-MnO2矿物氧化As(Ⅲ)的动力学过程,构建了可用于多相体系的搅拌-流动氧化还原反应动力学模型.经过As吸附量的校正后,该模型对酸性水钠锰矿及水羟锰矿氧化As(Ⅲ)动力学数据拟合度分别为0.980和0.951,模型拟合得到pH 7时2种矿物单位比表面上氧化As(Ⅲ)的初始反应速率常数k分别为0.131,0.014min-1·m-2.相比而言,该速率常数明显高于批量法得到的表观速率常数kobs,0.021,0.001min-1?m-2更接近真实的化学动力学参数.搅拌流动法与批量法得到的不同矿物的速率常数大小趋势一致,即尽管酸性水钠锰矿对As(Ⅲ)的氧化率低于水羟锰矿,单位比表面上酸性水钠锰矿氧化As(Ⅲ)初始反应速率却远高于水羟锰矿.反应过程分析表明,反应初始阶段,As(Ⅲ)的吸附为主要限速步骤;而随着反应的进行,矿物表面反应位点逐渐钝化或减少,反应位点数量成为限速步骤.     

Electro-Fenton法处理印染废水应用研究进展

Electro-Fenton法是利用电解的方法产生Fe2+和H2O2,新生的Fe2+和H2O2作用产生·OH。作为一种新兴的废水处理技术,在处理难降解有机废水方面,国内外已开展了广泛的研究,对于处理高浓度难降解有机废水效果良好。阐述了Electro-Fenton法的发展、分类、反应机理及其在印染废水处理中的应用研究现状,并指出Electro-Fenton法存在的主要问题和今后的发展方向。     

生物法处理海上油田含聚生产污水研究报告

应用"倍加清"特种微生物技术,结合"气浮+生化+固液分离"的处理工艺,以中海油绥中SZ36-1陆上终端含聚污水为水质样本,研究生物法处理海上油田含聚生产污水的效果。结果表明,该工艺处理后出水可达"1.5.2"的水质标准,远优于"10.10.3"的注入水质指标要求,并确定了相关技术参数。该技术具备处理效果好、适应来水水质范围大、环境友好等优势。但由于空间重量的限制,尚不适用于海上油田平台的生产水处理工艺。     

脱水污泥中聚合物的碱提取及其镉吸附效能研究

市政污水处理厂产生的脱水剩余污泥中含有大量的细菌胞外聚合物、胞内聚合物等大分子有机物,是一种良好的生物吸附剂制备原料。以脱水污泥为原料,采用碱提取的方法,对污泥中胞外聚合物与胞内聚合物进行提取,提取得到聚合物吸附剂,分析了聚合物吸附剂中聚合物浓度、核酸浓度随提取剂中NaOH浓度的变化,考察了聚合物吸附剂对水中镉的等温吸附性能。研究结果表明,当NaOH浓度小于0.5 mol/L时,随着提取剂NaOH浓度的升高,得到的提取液中聚合物浓度、核酸浓度逐渐升高。最佳的提取剂中NaOH浓度为0.3 mol/L,该条件下能够充分实现污泥中聚合物的提取。当NaOH浓度高于0.5 mol/L,聚合物中核酸存在一定程度的分解。聚合物吸附剂对水中Cd2+的吸附符合Langmuir模型,NaOH浓度为0.3 mol/L条件下提取得到的聚合物吸附剂的镉饱和吸附容量最大,达1.022 mmol/g。     

电感耦合等离子体原子发射光谱法测定电路板中金属含量的方法改进

根据样品中被测元素的特点,采用硝酸-氢氟酸-高氯酸-硼酸-硝酸和硝酸体系,对电路板中金属元素进行消解,用电感耦合等离子体原子发射光谱法对电路板中的金属元素含量进行定量分析。该方法具有简单、准确的特点,可以快速分析电路板中的金属元素含量。     

Efficacy of two chemical coagulants and three different filtration media on removal of Aspergillus flavus from surface water

Aquatic fungi are common in various aqueous environments and play potentially crucial roles in nutrient and carbon cycling as well as interacting with other organisms. Species of Aspergillus are the most common fungi that occur in water. The present study was undertaken to elucidate the efficacy of two coagulants, aluminum sulfate and ferric chloride, used at different concentrations to treat drinking water, in removing Aspergillusflavus, as well as testing three different filtration media： sand, activated carbon, and ceramic granules, for their removal of fungi from water. The results revealed that both coagulants were effective in removing fungi and decreasing the turbidity of drinking water, and turbidity decreased with increasing coagulant concentration. Also, at the highest concentration of the coagulants, A. flavus was decreased by 99.6% in the treated water. Among ceramic granules, activated carbon, and sand used as media for water filtration, the sand and activated carbon filters were more effective in removing A.flavus than ceramic granules while simultaneously decreasing the turbidity levels in the test water samples. Post-treatment total organic carbon （TOC） and total nitrogen （TN） concentrations in the experimental water did not decrease; on the contrary, TN concentrations increased with the increasing dosage of coagulants. The filtration process had no effect in reducing TOC and TN in tested water.     

Effects of metal and acidic sites on the reaction by-products of butyl acetate oxidation over palladium-based catalysts

Catalytic oxidation is widely used in pollution control technology to remove volatile organic compounds. In this study, Pd/ZSM-5 catalysts with different Pd contents and acidic sites were prepared via the impregnation method. All the catalysts were characterized by means of N2 adsorption- desorption, X-ray fluorescence （XRF）, HE temperature programmed reduction （H2-TPR）, and NH3 temperature programmed desorption （NH3-TPD）. Their catalytic performance was investigated in the oxidation of butyl acetate experiments. The by-products of the reaction were collected in thermal desorption tubes and identified by gas chromatography/mass spectrometry. It was found that the increase of Pd content slightly changed the catalytic activity of butyl acetate oxidation according to the yield of CO2 achieved at 90%, but decreased the cracking by-products, whereas the enhancement of strong acidity over Pd-based catalysts enriched the by-product species. The butyl acetate oxidation process involves a series of reaction steps including protolysis, dehydrogenation, dehydration, cracking, and isomerization. Generally, butyl acetate was cracked to acetic acid and 2- methylpropene and the latter was an intermediate of the other by-products, and the oxidation routes of typical by-products were proposed. Trace amounts of 3-methylpentane, hexane, 2-methylpentane, pentane, and 2-methylbutane originated from iso4merization and protolysis reactions.     

Antimony smelting process generating solid wastes and dust：Characterization and leaching behaviors

A large amount of solid waste has been produced by the antimony smelting process in the＂World Capital of Antimony＂, Xikuangshan area in China. This study comprehensively investigated the physical and chemical characteristics of the various solid wastes, as well as the leaching behavior of the solid wastes, which included water-quenched slag,arsenic-alkali residue, desulfurized slag and blast furnace dust. These four types of waste were enriched in a variety of heavy metals and metalloids and more specifically with As and Sb levels up to 8.6 × 104 and 3.16 × 105mg/kg, respectively, in arsenic-alkali residue. For desulfurized slag and water-quenched slag, the leaching concentration of Sb significantly exceeded the acceptable limits during the leaching tests using the toxicity characteristic leaching procedure and the synthetic precipitation leaching procedure. In addition, As leaching in arsenic-alkali residue was extraordinarily hazardous, being three orders of magnitude higher than the regulatory level of As. According to the results of the extraction tests, all the tested wastes were classified as hazardous waste.     

美国饮用水化学候选污染物的筛选过程

介绍美国国家环境保护局建立饮用水化学候选污染物清单(contaminant candidate list,CCL)的总体情况。通过第3次化学候选污染物清单的建立过程,详细介绍了CCL3的建立程序和技术内容,对化学候选污染物结合健康危害和暴露程度的筛选方法和分步实施筛选的程序进行了说明,对我国确定管制化学物质的筛选工作提供了实践参考。