Determination of 27 pharmaceuticals and personal care products (PPCPs) in water: The benefit of isotope dilution

• Isotope dilution method was developed for the determination of 27 PPCPs in water. • The established method was successfully applied to different types of water samples. • The correction effect of corresponding 27 ILSs over 70 d was investigated. • Benefit of isotopic dilution method was illustrated for three examples. Pharmaceuticals and personal care products (PPCPs) are a unique group of emerging and non-persistent contaminants. In this study, 27 PPCPs in various water samples were extracted by solid phase extraction (SPE), and determined by isotope dilution method using liquid chromatography coupled to tandem triple quadruple mass spectrometer (LC-MS/MS). A total of 27 isotopically labeled standards (ILSs) were applied to correct the concentration of PPCPs in spiked ultrapure water, drinking water, river, effluent and influent sewage. The corrected recoveries were 73%–122% with the relative standard deviation (RSD)<16%, except for acetaminophen. The matrix effect for all kinds of water samples was<22% and the method quantitation limits (MQLs) were 0.45–8.6 ng/L. The developed method was successfully applied on environmental water samples. The SPE extracts of spiked ultrapure water, drinking water, river and wastewater effluent were stored for 70 days, and the ILSs-corrected recoveries of 27 PPCPs were obtained to evaluate the correction ability of ILSs in the presence of variety interferences. The recoveries of 27 PPCPs over 70 days were within the scope of 72%–140% with the recovery variation<37% in all cases. The isotope dilution method seems to be of benefit when the extract has to be stored for long time before the instrument analysis.     

Performance evaluation of reverse logistics enterprise – an agent-based simulation approach

Reverse logistics (RL) has been applied in many industries and sectors since its conception. Unlike forward logistics, retracing consumer goods from the point of consumption to the point of inception is not a well-studied process. It involves many uncertainties such as time, quality and quantity of returns. The returned products can be remanufactured, have parts harvested, or be disposed safely. It is important to implement these activities in a cost-effective manner. The aim of this research is to measure the performance of the RL enterprise with the help of an agent-based simulation model. The major entities in the RL network are considered as Agents that can act independently. There are several different agents: collector agent, sorting-cum-reuse agent, remanufacturing agent, recycler agent, supplier agent and distributor agent. The individual performances of the agents are measured and recommendations are given to improve their performance, leading to the enhancement of the total performance of the RL enterprise. The approach is applied to a case study involving cell phone remanufacturing.     

Co-treatment of fruit and vegetable waste in sludge digesters. An analysis of the relationship among bio-methane generation,process stability and digestate phytotoxicity

The co-digestion of a variable amount of fruit and vegetable waste in a waste mixed sludge digester was investigated using a pilot scale apparatus. The organic loading rate (OLR) was increased from 1.46 kg VS/m³ day to 2.8 kg VS/m³ day. The hydraulic retention time was reduced from 14 days to about 10 days. Specific bio-methane production increased from about 90 NL/kg VS to the maximum value of about 430 NL/kg VS when OLR was increased from 1.46 kg VS/m³ day to 2.1 kg VS/m³ day. A higher OLR caused an excessive reduction in the hydraulic retention time, enhancing microorganism wash out. Process stability evaluated by the total volatile fatty acids concentration (mg/l) to the alkalinity buffer capacity (eq. mg/l CaCO₃) ratio (i.e. FOS/TAC) criterion was <0.1 indicating high stability for OLR <2.46 kg VS/m³ day. For higher OLR, FOS/TAC increased rapidly. Residual phytotoxicty of the digestate evaluated by the germination index (GI) (%) was quite constant for OLR < 2.46 kg VS/m³ day, which is lower than the 60% limit, indicating an acceptable toxicity level for crops. For OLR > 2.46 kg VS/m³ day, GI decreased rapidly. This corresponding trend between FOS/TAC and GI was further investigated by the definition of the GI ratio (GIR) parameter. Comparison between GIR and FOS/TAC suggests that GI could be a suitable criterion for evaluating process stability.     

流态对生物添加强化硝化效果的影响

在15℃、相同氮负荷和添加强度条件下运行SBR和CSTR以对比分析两种典型流态(推流式和完全混合式)对硝化菌添加强化硝化效果的影响.结果表明,添加期间,SBR中氨氧化速率(AUR)和亚硝酸盐氧化速率(NUR)分别为添加前的2.34和2.39倍,停止添加后又分别降为添加前的2.01和1.78倍;添加期间CSTR中AUR和NUR分别为添加前的2.63和2.44倍,停止添加后又分别降为添加前的1.48和1.31倍.荧光原位杂交结果显示,添加期间,SBR中氨氧化菌(AOB)和亚硝酸盐氧化菌(NOB)的个数百分比分别为添加前的2.67和2.71倍,添加停止后,又分别降至原来的2.14和1.95倍;CSTR中AOB和NOB分别为添加前的2.91和1.77倍,但在添加停止后CSTR中AOB和NOB分别降至添加前的1.25和1.50倍.因此,硝化菌添加期间,两种流态的添加效果接近,但是在添加停止后,由于流态对硝化菌中K-决策者(Nitrosospira、Nitrospira)和r-决策者(Nitrosomonas europaea、Nitrobacter)的选择作用,添加的硝化菌在完全混合式条件下比推流式条件下更容易被系统淘汰.     

不同运行模式下改良型CAST工艺处理生活污水的除磷性能

实验采用改良型CAST工艺,以生活污水为研究对象,考察了C/P、回流比及温度等不同运行模式对系统除磷性能的影响.结果表明,常温条件下进水C/P由50升至100,系统除磷率均值从15%迅速升至95.6%,除磷性能显著提高;继而降低C/P至75,除磷性能因进水碳源不足再度下降,除磷率均值为51.4%,且长期投加易降解碳源引发系统污泥膨胀并导致污泥大量流失.C/P较低情况下,回流比由25%降低至12.5%,除磷性能提高2.3倍,继续降低回流比至0,除磷性能反而下降;温度实验研究则表明,低温系统(14℃±1℃),除磷率稳定维持在90%以上,而高温短程硝化系统(27℃±1℃)除磷率仅为14.1%,可见低温更有利于系统磷的去除.吸磷小试发现,常温系统污泥以O_2、NO_3~-和NO_2~-为电子受体均能进行吸磷,而低温系统污泥能以O_2、NO_3~-为电子受体进行吸磷,高温系统污泥则仅能以O_2为电子受体进行少量吸磷.此外,实验还发现,系统短期闲置导致的污泥"饥饿"有利于系统除磷率的提高.     

微生物燃料电池改性阳极处理PTA废水

探讨了不同改性阳极对微生物燃料电池(microbial fuel cell,MFC)产电性能及其对MFC处理难降解废水能力的影响.以单室空气阴极为基础,利用0.1 g电气石、质量分数75%二氧化锰/埃洛石纳米管(manganese bioxide/halloysite nanotube,MnO_2/HNT)和多壁碳纳米管-羧基(multi-walled carbon nanotube-carboxyl,MWCNT-COOH)对MFC阳极进行修饰.结果表明,不同改性阳极的MFC对含精对苯二甲酸(purified terephthalic acid,PTA)废水的去除率均高于70%,且化学需氧量(chemical oxygen demand,COD)去除率在79%以上.相较于其他几种改性阳极,以MWCNT-COOH改性材料作阳极的MFC产生的最大输出电压最高,获得的最大功率密度最高,分别为529 mV和252.73 mW·m~(-2).     

Applicability of LIVE/DEAD BacLight stain with glutaraldehyde fixation for the measurement of bacterial abundance and viability in rainwater

Rainwater contains substantial bacteria and rain is an efficient pathway for the dissemination of bacteria from the atmosphere to land and water surfaces.However,quantitative information on rainwater bacteria is very limited due to the lack of a reliable method.In this study,the epifluorescence microscopy enumeration with the LIVE/DEAD BacLight Bacterial Viability Kit stain was verified to quantify the abundance of viable and non-viable bacterial cells in rainwater,with the 4',6-diamidino-2-phenylindole(DAPI) stain for the reference of total cell counts.Results showed that the total counts of bacterial cells by LIVE/DEAD BacLight staining were consistent with those by DAPI staining,and the average detection efficiency was(109 ± 29)%.The ratio of cell count with glutaraldehyde fixation to that without fixation was(106 ± 5)%on average.The bacterial concentration in negative control was usually an order of magnitude lower than that in rainwater samples.However,in case of small precipitation,the abundance in negative control could be more than that in rainwater samples.These results indicate that the enumeration with LIVE/DEAD BacLight bacterial viability assay coupled with glutaraldehyde fixation and careful negative control investigation is an approach applicable to the measurement of the concentration and viability of bacterial cells in rainwater.     

高含氮印染废水强化脱氮处理组合工艺

为考察UASB-A/LO/O（缺氧/低氧/好氧）组合工艺的实际应用效果,将该工艺应用到规模为6 000 t/d的实际工程中,考察其对高含氮印染废水处理效果,同时采用微生物高通量测序对A/LO/O工艺中的微生物菌群结构进行解析.结果表明:在前处理废水进水流量为100 m3/h,染色废水进水流量为150 m3/h,同时A/LO/O工艺污泥回流比为50%左右情况下,COD_Cr、NH₃-N和TN的去除率分别达到91.6%、95.5%和73.5%;染色和前处理废水在改良UASB内均实现了高效厌氧氨化,染色废水厌氧出水中ρ（NH₃-N）/ρ（TN）保持在80%以上,前处理废水厌氧出水保持在85%以上;调节UASB运行参数可对VFAs（挥发性脂肪酸）进行有效调控,从而为后段反硝化工艺提供高品质碳源,实现高效脱氮;A/LO/O系统对COD_Cr、NH₃-N、TN有较好的去除效果,其脱氮性能主要靠变性菌门（Proteobateria）发挥作用,该系统中低氧池的微生物种类最为丰富且发生短程硝化反硝化,对污染物去除贡献最大,当低氧池△ρ（COD_Cr）/△ρ（TN）在18.6左右时,TN去除率最高,达到82%.研究显示,该组合工艺对工程中高含氮印染废水的脱氮效果良好.      

Ti/SnO_2-Sb阳极-空气阴极电催化降解染料废水

为解决电化学法处理高盐染料废水存在的能耗大、成本高等问题,分别采用溶胶-凝胶法和辊压法制备Ti/SnO_2-Sb阳极和空气阴极,构建了Ti/SnO_2-Sb阳极-空气阴极双极体系(TSSA-ADC)。甲基橙(MO)作为高盐染料废水的典型污染物,考察了电流强度、MO浓度、电解液浓度和初始p H对TSSA-ADC体系和TSSA单阳极体系降解MO的影响。结果表明:与TSSA单阳极体系相比,TSSA-ADC体系具有更好的抗有机负荷冲击、抗盐分冲击、抗酸碱波动能力,能够维护酸碱平衡防止硬度离子结垢。最佳反应条件为电流强度为0.030 A,电解液浓度为3%,MO浓度为100 mg/L,初始pH=6。以MO去除率达到98%为基准,TSSA-ADC体系比TSSA体系可节能74.26%。     

Ti/SnO_2-Sb阳极-空气阴极电催化降解染料废水

为解决电化学法处理高盐染料废水存在的能耗大、成本高等问题,分别采用溶胶-凝胶法和辊压法制备Ti/SnO_2-Sb阳极和空气阴极,构建了Ti/SnO_2-Sb阳极-空气阴极双极体系(TSSA-ADC)。甲基橙(MO)作为高盐染料废水的典型污染物,考察了电流强度、MO浓度、电解液浓度和初始p H对TSSA-ADC体系和TSSA单阳极体系降解MO的影响。结果表明:与TSSA单阳极体系相比,TSSA-ADC体系具有更好的抗有机负荷冲击、抗盐分冲击、抗酸碱波动能力,能够维护酸碱平衡防止硬度离子结垢。最佳反应条件为电流强度为0.030 A,电解液浓度为3%,MO浓度为100 mg/L,初始pH=6。以MO去除率达到98%为基准,TSSA-ADC体系比TSSA体系可节能74.26%。