钢铁行业废水零排放技术探索

针对钢铁行业废水特点,分析了目前钢铁行业各工序及全厂主要废水污染控制措施,重点分析了二级反渗透工艺的主要流程及进出水水质,以及该工艺存在的主要问题。通过对大型钢铁集团的现场调研,以太钢采用的反渗透和蒸发结晶工艺为例分析了钢铁行业真正实现废水零排放的技术可行性。该技术可以很好解决钢铁行业浓盐水的外排问题。     

碳酸盐体系中pH对Cu2+诱导结晶过程的影响

在流化床中,以含Cu2+废水为处理对象,考察了碳酸盐体系中pH的改变对Cu2+诱导结晶过程的影响. 结果表明:当进水ρ(Cu2+)为200 mg/L、沉淀剂pH为10.2时,经回流系统拦截,微晶产率可降低0.5%~1.0%,Cu2+的去除率可达99.0%以上. 经XRD(X射线衍射)分析表明,结晶产物以碱式碳酸铜为主,晶型呈短杆状,尺寸较为均一;当沉淀剂pH升至12.2时,Cu2+的去除率降至95.0%,系统出水结晶产物晶型特征不明显,尺寸不均,XRD结果显示为氢氧化铜、碱式碳酸铜、碳酸钙等混合结晶产物,晶体衍射峰多存在宽化现象,表明高pH下结晶产物晶化程度较低.      

Crystallization and X‐ray structure of 3,3’,4‐trichlorobiphenyl (PCB 35)∗

A method for the preparation of single crystals of PCB 35 suitable for single crystal X‐ray structure determination was developed. This method has already been proven suitable for 2,4'‐dichlorobiphenyl and may prove useful for other PCBs or related compounds. The crystals of PCB 35 are orthorhombic, spacegroup P2₁22₁ (a= 10.665(8), 6 = 3.825(3), c= 14.086(9) Å) and the structure was refined to R = 0.094 for 156 unique observed reflections and 43 parameters. Although the crystals were of poor quality, the structure determination unequivocally confirmed the substitution pattern of the biphenyl moiety by Cl atoms inferred previously from spectroscopic methods. The dihedral angle between the planes of the two phenyl rings is 33(2)°.     

粉煤灰源NaY沸石的制备及其对乙酸乙酯的吸附性能研究

采用粉煤灰合成沸石的方法既经济又环保,在乙酸乙酯吸附领域中具有巨大应用前景.遵循节能减排、废物再利用的环保原则,探索了3种不同Si/Al比的粉煤灰、结晶温度、结晶时间和碱浓度4个因素对合成NaY沸石的影响.XRD、氮气吸脱附实验及ICP结果表明,Si/Al比和水热结晶温度对高比表面积NaY沸石的合成影响最大.Si/Al比在1左右的粉煤灰合成的沸石比表面积较低,且晶形中存在大量的NaA沸石,而Si/Al比在2左右的粉煤灰合成了高比表面积且纯度较高的NaY沸石;3种粉煤灰均在65 ℃下合成NaY沸石,但在105 ℃下完全转化为方钠石.实验优化结果表明,最优合成条件为采用Si/Al为2左右的粉煤灰,在2 mol·L^-1碱浓度、65 ℃水热温度下结晶12 h.该条件下合成的NaY沸石比表面积高达654.86 m²·g^-1(比表面积最高的粉煤灰源沸石之一),是原粉煤灰比表面积的22倍左右,对乙酸乙酯的吸附量也由15.4 mg·g^-1增至108.2 mg·g^-1.     

诱导结晶反应中介稳区的研究

CaCl₂-Na₂CO₃溶液体系中c(Ca2+)和c(CO₃2-)处于介稳区中,是该体系诱导结晶反应能够进行的前提条件.临界值点是介稳区的边界点,应用电导率法测定CaCl₂-Na₂CO₃溶液体系的临界值点,对影响临界值的温度,pH,反应时间和搅拌强度等因素进行了研究,绘制了不同条件下CaCl₂-Na₂CO₃溶液体系的介稳区.结果表明,降低温度,增加溶液的pH,搅拌强度适中能够降低出现临界值时的电导率,增加介稳区的面积.考虑到试验的可操作性和成本等因素,确定CaCl₂-Na₂CO₃溶液体系诱导结晶反应的最佳条件:温度为25 ℃,pH为9.0,反应时间为10 min,搅拌强度为200 r/min.在最佳反应条件下,c(Ca2+)和c(CO₃2-)满足3.496×10-10［Ca2+］-1.182 6<［ CO₃2-］<4.96×10-9［Ca2+］>/sup>-1时,诱导结晶反应能够在介稳区中进行.      

Nest site selection and induced response in a dominant arboreal ant species

It is well known that arboreal ants, both territorially dominant species and plant ants (e.g., species associated with myrmecophytes or plants housing them in hollow structures), protect their host trees from defoliators. Nevertheless, the presence of an induced defense, suggested by the fact that the workers discovering a leaf wound recruit nestmates, is only known for plant ants. Based on the results from a field study, we show here (1) that colonies of Azteca chartifex, a territorially dominant, neotropical arboreal ant species, mostly selected Goupia glabra (Goupiaceae) trees in which to build their principal carton nests and (2) that plant signals induced workers to recruit nestmates, which patrol the leaves, likely providing the plant with a biotic defense. Furthermore, the number of recruited workers was clearly higher on G. glabra, their most frequently selected host tree species, than on other tree species. These results show that contrary to what was previously believed, induced responses are also found in territorially dominant arboreal ants and so are not limited to the specific associations between myrmecophytes and plant ants.     

生态聚磷石对低浓度景观水的除磷研究

研究了新型填料水化硅酸钙对景观水中低浓度磷的去除效果。考察了反应时间、初始磷浓度、投加量对除磷率的影响,同时采用以水化硅酸钙为填料的滤床,研究其实际低浓度景观水中磷去除效果。结果表明,初始磷浓度为0.3mg/L的低浓度模拟水,在投加量为1500mg/L、反应时间为24h时,水化硅酸钙对模拟水中除磷率达到60%以上,针对浓度为0.50mg/L的实际景观水,投加量为800mg/L时,除磷率达到65.0%;动态试验中,水力停留时间为60min、初始磷浓度为0.15～0.3mg/L,运行8d后,过滤床除磷率保持在44%以上。     

A Literature Review of Poly(Lactic Acid)

A literature review is presented regarding the synthesis, and physicochemical, chemical, and mechanical properties of poly(lactic acid)(PLA). Poly(lactic acid) exists as a polymeric helix, with an orthorhombic unit cell. The tensile properties of PLA can vary widely, depending on whether or not it is annealed or oriented or what its degree of crystallinity is. Also discussed are the effects of processing on PLA. Crystallization and crystallization kinetics of PLA are also investigated. Solution and melt rheology of PLA is also discussed. Four different power-law equations and 14 different Mark–Houwink equations are presented for PLA. Nuclear magnetic resonance, UV–VIS, and FTIR spectroscopy of PLA are briefly discussed. Finally, research conducted on starch–PLA composites is introduced.     

改性氧化铝微波诱导氧化处理雅格素蓝BF-BR染料废水的研究

采用微波诱导氧化工艺(MIOP)技术,以改性氧化铝为催化剂,对雅格素蓝BF-BR染料模拟废水进行氧化处理．优化了处理工艺条件,实验在固液质量比为1：10(50mL雅格素蓝BF-BR水溶液中投加5．0g改性氧化铝)、微波功率为400W的条件下微波辐照处理5min．在此工艺条件下,对水中雅格素蓝BF-BR的脱色率可达到98％,COD去除率为87．4％．改性氧化铝在重复使用9次后仍能保持很高的脱色率．进一步研究表明在微波辐射场中废水中的有机污染物在改性氧化铝表面通过吸附．氧化协同作用而被迅速降解．反应动力学研究表明,该氧化过程符合一级反应动力学规律,反应速率常数k=0995min^-1,反应半衰期t1/2=0．697min．实验结果显示,在本实验中改性氧化铝比颗粒活性炭具有更高的催化活性．     

Assessing the economic feasibility of regional deep saline aquifer CO2 injection and storage: A geomechanics-based workflow applied to the Rose Run sandstone in Eastern Ohio, USA

Typical top-down regional assessments of CO₂ storage feasibility are sufficient for determining the maximum volumetric capacity of deep saline aquifers. However, they do not reflect the regional economic feasibility of storage. This is controlled, in part, by the number and type of injection wells that are necessary to achieve regional CO₂ storage goals. In contrast, the geomechanics-based assessment workflow that we present in this paper follows a bottom-up approach for evaluating regional deep saline aquifer CO₂ storage feasibility. The CO₂ storage capacity of an aquifer is a function of its porous volume as well as its CO₂ injectivity. For a saline aquifer to be considered feasible in this assessment it must be able to store a specified amount of CO₂ at a reasonable cost per ton of CO₂. The proposed assessment workflow has seven steps that include (1) defining the storage project and goals, (2) characterizing the geology and developing a geomechanical model of the aquifer, (3) constructing 3D aquifer models, (4) simulating CO₂ injection, (5,6) evaluating CO₂ injection and storage feasibility (with and without injection well stimulation), and (7) determining whether it is economically feasible to proceed with the storage project. The workflow was applied to a case study of the Rose Run sandstone aquifer in the Eastern Ohio River Valley, USA. We found that it is feasible in this region to inject 113 Mt CO₂/year for 30 years at an associated well cost of less than US $1.31/t CO₂, but only if injectivity enhancement techniques such as hydraulic fracturing and injection induced micro-seismicity are implemented.