Risk reduction concept to provide design criteria for Emergency Systems for onshore LNG plants

The functional safety requirement is widely applied in the process plant industry in accordance with the international standards, such as IEC and ISA. The requirement is defined as safety integrity level (SIL) based on the risk reduction concept for protection layers, from original process risk to tolerable risk level. Although the standards specify both, the Prevention System and the Emergency System, as level of protection layers, the standards specify in detail only the use of the Prevention System (i.e., Safety Instrumented System (SIS)). The safety integrity level is not commonly allocated to the Emergency System (e.g., Fire and Gas System, Emergency Shutdown System and Emergency Depressuring System). This is because the required risk reduction can be normally achieved by only the Prevention System (i.e., SIS and Pressure Safety Valve (PSV)). Further, the risk reduction level for the Emergency System is very difficult to be quantified by the actual SIL application (i.e., evaluated based on the single accident scenario, such as an accident from process control deviation), since the escalation scenarios after Loss of Containment (LOC) greatly vary depending on the plant design and equipment. Consequently, there are no clear criteria for evaluating the Emergency System design. This paper aims to provide the functional safety requirement (i.e., required risk reduction level based on IEC 61508 and 61511) as design criteria for the Emergency System.In order to provide clear criteria for the Emergency System evaluation, a risk reduction concept integrated with public’s perception of acceptable risk criteria is proposed and is applied to identify the required safety integrity level for the Emergency System design. Further, to verify the safety integrity levels for the Emergency Systems, the probabilistic model of the Emergency Systems was established considering each Emergency System (e.g., Fire and Gas System, Emergency Shutdown System and Emergency Depressuring System) relation as the Overall Emergency System. This is because the Overall Emergency System can achieve its goal by the combined action of each individual system, including inherent safe design, such as separation distance.The proposed approach applicability was verified by conducting a case study using actual onshore Liquefied Natural Gas Plant data. Further, the design criteria for Emergency Systems for LNG plants are also evaluated by sensitivity analysis.     

小议火电厂总量减排核查要点

从资料核查、在线监测设备核查、集控系统核查及现场核查4个环节详细介绍了火电厂总量减排现场核查的要点。对核查中出现的问题进行总结及分析,为同类环境管理工作提供参考。     

新型二氧化铅电极处理染料废水

利用高压塑片法制备掺杂镧和活性炭以及聚四氟乙烯(PTFE)的新型二氧化铅电极,采用X衍射(XRD),循环伏安曲线(CV),扫描电镜(SEM)等手段对电极性能进行表征,研究了其电催化处理有机染料废水(亚甲基蓝)的降解效果,并对反应机理进行了相关研究。研究表明,该电极具有良好的抗腐蚀能力,对亚甲基蓝具有较好的降解效果。通过与普通二氧化铅电极比较,该电极在染料脱色和去除COD方面都有较明显优势,显示出较好的工业应用前景。     

不同酶强化污泥为燃料微生物燃料电池特性对比分析

采用单室无膜悬浮阴极微生物燃料电池(MFC),对比分析了蛋白酶和淀粉酶强化剩余污泥为燃料的MFC(ESMFC)产电特性、酶特性和污泥减量化效果。研究表明,投加蛋白酶的ESMFC最大功率密度比对照组增加106.2%,投加淀粉酶时ESMFC最大功率密度比对照组增加48%。蛋白酶作用主要体现在投加后的前12小时,而淀粉酶作用时间则较长,为投加后的前144小时,但在运行前期,由于高温作用,导致系统内的酶活性较强,投加的淀粉酶作用则不明显。投加蛋白酶的系统内TCOD、TSS和VSS去除率分别为82%、65%和85%,而投加淀粉酶的系统内TCOD、TSS和VSS去除率分别达到86%、67%和88%。此研究对于ESMFC中外加酶的选择具有一定意义。     

铁氧化物复合氧化铝催化臭氧化过程中溴酸盐的生成控制

以市售活性炭、硅藻土和氧化铝小球为载体,考察了负载铁基活性组分对催化臭氧化过程中溴酸盐的控制情况,其中,铁基复合氧化铝小球体现出更好的溴酸盐还原特性和催化剂稳定性,证实催化剂中铁氧化物是溴酸盐得到有效控制的主要活性组分。进一步考察了铁基复合氧化铝小球催化臭氧化处理实际原水过程中对溴酸盐的生成控制,以及反应过程中溶解性有机碳（DOC）的去除情况。结果表明,与单独臭氧化相比,该催化剂既能有效去除水中的溶解性有机物,又能明显抑制溴酸盐的生成,反应50h,其活性并没有明显下降。催化剂失活主要归因于吸附位点数量的下降,可以通过负载铁氧化物来实现催化剂的再生。     

CuO / 过硫酸氢钾体系催化氧化苯酚简

本论文通过直接沉淀法制备了CuO催化剂,结合过硫酸氢钾,在常温常压下催化氧化处理苯酚模拟废水。采用电子显微镜（SEM）、X射线粉末衍射（XRD）对催化剂进行了表征,并研究了反应过程中各影响因素对降解效率的影响。实验结果表明,在催化剂用量为0.2 g/L,氧化剂浓度为0.25 g/L,pH值为7,反应时间为60 min的条件下,浓度为50 mg/L的苯酚降解率可达100%,TOC去除率达84%。进一步实验表明,催化剂具有良好的重复使用能力。最后,通过自由基捕捉实验,考察了体系中的自由基种类,并根据实验结果,讨论了CuO/过硫酸氢钾体系的催化降解机理。     

燃煤烟气低温SCR脱硝中试研究

低温选择性催化还原(SCR)脱硝是国内外脱硝技术研发的热点,但目前主要集中在实验室小试范围,无法完全反映催化剂在实际烟气中的运行状况。在30 t/h循环流化床燃煤锅炉脱硫除尘装置后建设了2 000~5 000 m3/h的SCR脱硝中试装置,经系统研究发现,中试使用的蜂窝式催化剂对SO2和NO具有很强的吸附能力,且反应温度、喷氨速率和气体空速均会影响催化脱硝效率。为期5 d的连续运行实验结果表明,催化剂的脱硝效率一直稳定在30%~50%,并未发现明显的失活,这证明设计除雾除尘器、较大的混合器、混合器与反应器间较长的管路均有利于缓解催化剂因SO2、H2O和飞灰中的碱性金属导致的失活。     

锰铜铈氧化物催化剂氧化NO性能及动力学研究

实验以TiO2为载体采用浸渍法制备CuOx/TiO2、CeOx/TiO2、CuCeOx/TiO2和MnCuCeOx/TiO2催化剂,考察这些催化剂氧化NO活性,探究Cu、Ce摩尔比和添加Mn元素对CuCeOx/TiO2催化剂氧化NO活性的影响,使用扫描电镜观察催化剂表面结构.研究发现,Cu、Ce元素配合后的CuCeOx/TiO2催化剂氧化活性明显好于单独含Cu、Ce的催化剂,当Cu、Ce摩尔比为Cu:Ce=1:2时,CuCeOx/TiO2催化剂氧化活性最好,在NO浓度500×10-6,O2 10%,空速为24 000 h-1,350℃时,NO氧化度为0.62;添加Mn元素可以提高CuCeOx/TiO2催化剂低温氧化活性, 250℃时,MnCuCe/Ti-3和MnCuCe/Ti-5催化剂氧化度为0.53和0.69,300℃时,MnCuCe/Ti-3和MnCuCe/Ti-5催化剂氧化度均为0.76;此外,实验还研究了NO在MnCuCe/Ti-3催化剂上反应的动力学方程.     

复合钙基固硫添加剂对煤固硫与燃烧的影响

利用程序升温燃烧反应技术,考察了高岭土复合的CaO、Fe2O3-CaO、CoO-CaO添加剂对无烟煤的燃烧以及固硫的影响。实验发现,这些添加物质对煤的裂解产物的燃烧都具有促进作用,除了Fe2O3-CaO-高岭土复合添加剂对煤焦的燃烧有一定阻碍作用之外,其余都具有对煤焦燃烧的促进作用,尤以CoO-CaO-高岭土复合添加剂的效果最为显著。高岭土复合的硫酸钙本应具有较高的热稳定性,但受到高温下煤焦与CO的还原而分解,所以添加对煤焦具有明显催化燃烧作用的氧化钴,因减少了还原性气氛,稳定了硫酸钙产物而促进了固硫。     

Reduction of Baltic Sea Nutrient Inputs and Allocation of Abatement Costs Within the Baltic Sea Catchment

The Baltic Sea Action Plan (BSAP) requires tools to simulate effects and costs of various nutrient abatement strategies. Hierarchically connected databases and models of the entire catchment have been created to allow decision makers to view scenarios via the decision support system NEST. Increased intensity in agriculture in transient countries would result in increased nutrient loads to the Baltic Sea, particularly from Poland, the Baltic States, and Russia. Nutrient retentions are high, which means that the nutrient reduction goals of 135 000 tons N and 15 000 tons P, as formulated in the BSAP from 2007, correspond to a reduction in nutrient loadings to watersheds by 675 000 tons N and 158 000 tons P. A cost-minimization model was used to allocate nutrient reductions to measures and countries where the costs for reducing loads are low. The minimum annual cost to meet BSAP basin targets is estimated to 4.7 billion €.