Feasibility of honeycomb monolith supported sugar catalyst to produce biodiesel from palm fatty acid distillate (PFAD)

Carbon coated monolith was prepared by sucrose solution 65 wt.% via dip-coating method. Sulfonation of incomplete carbonized carbon coated monolith was carried out in order to synthesize solid acid catalyst. The textural structure characteristics of the solid acid catalyst demonstrated a low surface area and pore volume. Palm fatty acid distillate (PFAD), a by-product of palm oil refineries, was utilized as oil source in biodiesel production. The esterification reaction subjected to different reaction conditions was performed by using the sulfonated carbon coated monolith as heterogeneous catalyst. The sulfonation process had been performed by using vapour of concentrated H₂SO₄ that was much easier and efficient than liquid phase sulfonation. Total acidity value of carbon coated monolith was measured for unsulfonated sample (0.5 mmol/g) and sulfonated sample (4.2 mmol/g). The effect of methanol/oil ratio, catalyst amount and reaction time were examined. The maximum methyl ester content was 89% at the optimum condition, i.e. methanol/oil molar ratio (15:1), catalyst amount (2.5 wt.% with respect to PFAD), reaction time (240 min) and temperature 80 °C. The sugar catalyst supported on the honeycomb monolith showed comparable reactivity compared with the sugar catalyst powder. However, the catalyst reusability studies showed decrease in FFA% conversion from 95.3% to 68.8% after four cycles as well as the total acidity of catalyst dropped from the value 4.2 to 3.1 mmol/g during these cycles. This might be likely due to the leaching out of SO₃H group from the sulfonated carbon coated monolith surface. The leaching of active species reached a plateau state after fourth cycle.     

NOx存在条件下相对湿度对甲苯氧化产物的影响

利用流动管反应器模拟甲苯与氧化剂×OH在NO_x存在条件下的反应,定量测定了不同相对湿度条件下（17.5%、35%、50%、70%）反应生成的部分气相产物和颗粒相产物,计算了不同相中产物产率,测量了不同相对湿度下的颗粒相有机碳（OC）产率,推导了相对湿度对甲苯氧化反应的影响机制.结果表明,相对湿度不仅对甲苯与×OH反应途径比例有影响,还对产物的产率及氧化程度有影响.     

金属表面涂装行业VOCs排放特征及排放系数

对比了浙江省2014和2018年金属表面涂装企业的有机废气排放及治理情况,分析了该行业涂料及稀释剂的使用、主要污染因子,测算了溶剂型、水性涂料的挥发性有机物（VOCs）产生系数和排放系数.结果表明：2018年VOCs治理水平明显高于2014年,水性涂料使用企业比例由18%上升至36%,纯溶剂型企业由82%下降至64%;金属表面涂装行业的主要排放污染物为二甲苯、丁醇、乙酸乙酯、乙酸丁酯、甲苯、丙二醇、乙苯、苯乙烯等8种有机物.溶剂型和水性涂料的VOCs产生系数分别为0.72和0.31kg/kg;溶剂型和水性涂料2014年VOCs排放系数为0.64和0.29kg/kg,2018年为0.48和0.21kg/kg.     

离子液体吸收废印刷线路板热拆解过程中挥发性有机物——基于COSMO-RS模型

模拟废印刷线路板（WPCB）的热拆解过程,分析热拆解过程中的挥发性有机物（VOCs）组分;利用真实溶剂似导体屏蔽（COSMO-RS）模型对浓度较高的污染物进行量子力学模拟,研究离子液体（ILs）组成单元对目标污染物溶解度的影响差异,分析溶解过程中主导分子间作用力类型,确定优选吸收剂;测定不同溶剂进行溶解性,验证模型适用性.结果表明：①乙酸乙酯和环戊酮是浓度较高的VOCs组分,在240和250℃时浓度分别为43.1,153mg/m³和105,252mg/m³,质量百分比总和分别为76.3%和67.3%.②高表面屏蔽电荷密度分布峰、长烷基链阴阳离子和亲电基团的存在可提高乙酸乙酯和环戊酮在ILs中的溶解度.双三氟甲磺酰基亚胺盐（NTf₂^-）类ILs是一类优良吸收剂.静电力和范德华力对溶解过程起主导作用.③COSMO-RS模型可定性和半定量用于预测乙酸乙酯和环戊酮的溶解度.     

模拟土壤淋洗废液中重金属的选择性去除与淋洗液的回收研究

土壤淋洗废液中污染物的选择性去除是实现淋洗液回收的关键.本文以硫化钠（Na₂S）、乙基黄原酸钾（PEX）、二甲基二硫代氨基甲酸钠（DTC）作为重金属沉淀剂处理电子垃圾污染土壤模拟淋洗废液,在筛选出Na₂S作为理想重金属沉淀剂的基础上,研究初始pH值、反应温度、沉淀剂浓度等因素对Na₂S分离络合态重金属的影响,并通过软件模拟和产物表征等方式推测反应机理.结果表明：Na₂S对柠檬酸络合态重金属的分离顺序依次为Cu、Pb、Cd,符合硫化物溶度积原则;反应温度、初始pH值对Na₂S处理络合态重金属无显著影响,重金属去除率均保持在90%以上,柠檬酸的回收率约为95%;Visual MINTEQ模拟结果显示,S^2-投加前液相中重金属主要以H₂CA^-、HCA^2-和CA^3-结合形式存在,S^2-投加后液相中重金属则以HS^-和S^2-结合形式存在;扫描电镜及能谱（SEM-EDS）表明,S^2-与金属阳离子按物质的量比1：1生成硫化物沉淀物,沉淀主要呈团聚、成簇和圆片状存在;X射线衍射（XRD）分析结果表明,沉淀产物中存在CuS、CdS、PbS和CuPbS₂.本研究结果可为化学沉淀法处理重金属污染土壤淋洗废液提供技术参考.     

红树林土壤解磷菌的分离鉴定及解磷特性

从罗源湾红树林根际土壤中分离解磷菌,筛选出洋葱伯克霍尔德菌（Burkholderia cepacia, NR 113645.1）和短小芽孢杆菌（Bacillus pumilus, NR 043242.1）,研究它们的解磷特性和动态解磷过程. HPLC结果表明, B. cepacia菌液上清中含葡萄糖酸、丙酮酸、乳酸、乙酸、丁二酸, 这些有机酸的产生导致磷酸盐溶解. B.pumilus菌液上清中仅检测到少量的葡萄糖酸, 因此该菌溶磷效果不佳. 在细菌动态溶磷过程中发现, 经B. cepacia菌处理的磷酸钙, 其X射线衍射（XRD）特征峰强度随时间的增长降低, 显微镜图像显示磷酸钙颗粒随时间增长变小, 甚至消失. 而经B.pumilus菌处理的结果表明, 在试验期间内磷酸钙峰强度和颗粒大小没有明显变化. 细菌产生有机酸是溶解磷酸盐的重要前提, 这是解决板结土壤中难溶性磷源转化为生物可利用磷源问题的关键.     

酸性紫色水稻土颗粒有机质对镉的吸附特性

采集典型的酸性紫色水稻土（APPS）,从中分离出颗粒有机质（POM）,通过批量试验研究POM及其来源土壤Cd²⁺的吸附动力学、等温吸附和热力学特征,通过扫描电镜-能谱仪、傅里叶红外光谱仪等手段及吸附前后镉的形态变化的测定,研究了POM对Cd²⁺的吸附机制.结果表明：POM对Cd²⁺的亲和力远高于其来源土壤.POM及土壤对Cd²⁺的吸附动力学最优模型均为准二级动力学.Langmuir、Freundlich方程均能较好地描述其等温吸附特征,其中对POM,以Freundlich方程更优,表明POM对Cd²⁺的吸附属于多分子层的非均质吸附.吸附热力学参数△G^θ均小于0、△H^θ和△S^θ均大于0,表明吸附属于自发吸热过程.根据△H^θ值及解吸试验判定POM对Cd²⁺的吸附以化学吸附为主,土壤对Cd²⁺的吸附过程以物理吸附为主.吸附平衡后,土壤中可交换态镉比例提高,而POM中交换态和络合态镉比例增加.综上及吸附前后POM的表征结果说明,POM对Cd²⁺的吸附机制包括含氧官能团的络合、离子交换、阳离子-π键、沉淀作用和静电吸附.     

The study of biological activity of transformation products of diclofenac and its interaction with chlorogenic acid

In the present work we compared the biological activity of DCF, 4′-OHDCF and 5-OHDCF as molecules of most biodegradation pathways of DCF and selected transformation products (2-hydroxyphenylacetic acid; 2,5-dihydroxyphenylacetic acid and 2,6-dichloroaniline) which are produced during AOPs, such as ozonation and UV/H₂O₂. We also examined the interaction of DCF with chlorogenic acid (CGA). CGA is commonly used in human diet and entering the environment along with waste mainly from the processing and brewing of coffee and it can be toxic for microorganisms included in activated sludge. In the present experiment the evaluation of following parameters was performed: E. coli K-12 cells viability, growth inhibition of E. coli K-12 culture, LC₅₀ and mortality of Chironomus aprilinus, genotoxicity, sodA promoter induction and ROS generation. In addition the reactivity of E. coli SM recA:luxCDABE biosensor strain in wastewater matrices was measured. The results showed the influence of DCF, 4′-OHDCF and 5-OHDCF on E. coli K-12 cells viability and bacteria growth, comparable to AOPs by-products. The highest toxicity was observed for selected, tested AOPs by-products, in comparison to the DCF, 4′-OHDCF and 5-OHDCF. Genotoxicity assay indicated that 2,6-dichloroaniline (AOPs by-product) had the highest toxic effect. The oxidative stress assays revealed that the highest level of ROS generation and sodA promoter induction were obtained for DCF, 4′-OHDCF and 5-OHDCF, compared to other tested compounds. We have also found that there is an interaction between chlorogenic acid and DCF, which resulted in increased toxicity of the mixture of the both compounds to E. coli K-12, comparable to parent chemicals. The strongest response of E. coli SM biosensor strain with recA:luxCDABE genetic construct in filtered treated wastewaters, comparable to control sample was noticed. It indicates, that E. coli SM recA:luxCDABE biosensor strains is a good tool for bacteria monitoring in wastewater environment. Due to toxicity and biological activity of tested DCF transformation products, there is a need to use additional wastewater treatment systems for wastewater contaminated with pharmaceutical residues.     

达里诺尔湖水体DOM荧光特征及其来源解析

达里诺尔湖（简称“达里湖”）是内蒙古自治区高原地区重要的生态屏障,探究达里湖水质状况及污染来源,对加强流域水环境治理、改善水环境质量具有十分重要的意义.于2018年9月及2019年6月对湖水进行采样,并通过三维荧光光谱结合PARAFAC（平行因子分析）模型,探究达里湖水体DOM（溶解性有机质）来源及其与水质的关系.结果表明:①达里湖水体中pH较高,ρ（DOC）（DOC为溶解性有机碳）、ρ（NH₄+-N）、ρ（TP）相对较高,均超过GB 3838—2002《地表水环境质量标准》Ⅴ类水质标准限值.②水体中DOM含4种荧光组分.夏季水体DOM主要分布于河流入湖口附近,其中,类腐殖质荧光组分（紫外区类富里酸和可见区类富里酸）占总组分的62.93%,类蛋白类荧光组分（类色氨酸和类酪氨酸）占总组分的36.07%;秋季水体DOM主要分布于东南侧,其中,类腐殖质荧光组分占总组分的40.52%,类蛋白类荧光组分占总组分的59.48%.③达里湖采样点荧光参数表明,达里湖DOM自生源特征较强,腐殖化程度较低.类腐殖质荧光组分与ρ（DOC）、ρ（Chla）均呈正相关,类色氨酸荧光组分与pH呈正相关,类络氨酸与ρ（DTN）、ρ（NH4+-N）、ρ（DTP）均呈正相关.研究显示,达里湖DOM具有陆源与生物源双重特性,DOM的形成与微生物、细菌、浮游生物的生命活动密切相关.      

加入SOA示踪的深圳大气PM2.5受体模型源解析

为厘清包括二次有机气溶胶（SOA）在内的深圳市区PM_2.5各种一次和二次来源贡献,本文于2017年9月2日~2018年8月29日在深圳市大学城点位开展PM_2.5样品采集,并进行化学组分和水溶性有机物（WSOM）质谱测量,共获得162组有效数据.观测期间深圳市大气PM_2.5平均质量浓度为26μg/m³,在传统PMF源解析的基础上加入羧基离子碎片（CO₂⁺）作为SOA的示踪物,加入水溶性有机氧（WSOO）用于计算各因子O/C,验证有机物解析效果.结果表明,SOA可以被独立解析出,其O/C明显高于其他一次污染源中有机物;机动车、二次硫酸盐、二次硝酸盐、SOA为最主要的4个源,对PM_2.5质量浓度的贡献分别为25%、23%、17%和10%,船舶、地面扬尘、老化海盐、建筑尘、生物质燃烧、燃煤和工业贡献均在5%以内.各个源的变化特征表明,机动车、二次硫酸盐、二次硝酸盐、SOA等源贡献呈现冬高夏低的季节特征,与冬季季风条件下源自内陆的污染传输密切相关.污染天气时,二次硝酸盐和SOA的贡献增加相对最显著,因此NOx和挥发性有机物是减排的关键.