城市可降解生活垃圾的生物综合处理模式初探

针对现有城市生活垃圾处理方式的不足,结合垃圾生物处理特点,设计了集混合菌群降解、生物过滤除臭、污水回用及植被绿化于一体的立体处理体系。结果表明,该系统在城市生活垃圾的“三化”处理中具有显著的潜势:既使生活垃圾在食物链外形成安全的闭路循环,防止有害物质向人居环境入渗;同时,处理设施的立体化、终产物的生物转化以及即刻的市场效应,有效地增强了系统的消纳能力,缓解了传统处理方式对城市空间的压力。该系统对我国中小城市生活垃圾的综合利用具有积极的参考价值。     

长庆油田水处理新技术研究

长庆油房庄油田水经过处理后仍具有较高的矿化度、较多的悬浮物及残留油,同时其SRB严重超标。现场处理水质不稳定,在进行回注时与地层的配伍性较差。针对这些情况,研究了一种新型的水处理工艺技术。对成垢离子调整剂、水质净化剂和成垢离子钝化剂进行了筛选,并对含油污水的成垢离子含量及比例进行了调整。运用这种技术,使油房庄油田水经处理后达到回注水的标准,且提高了与地层的配伍性。同时提出了新型水处理技术的工艺流程。     

稠油污水处理系统改造与絮凝剂筛选试验研究

河南油田井楼稠油联合站含油污水中的污油和悬浮物含量较高,超过150mg/L。为此,对该处理系统进行了改造,并对絮凝剂的筛选进行了试验。结果表明:无机絮凝剂与有机絮凝剂联合作用,可对污水中所含有的污油和有机物杂质的悬浮物产生很好的絮凝沉降效果。加药浓度、加药顺序及沉降时间均对絮凝沉降效果有一定的影响。改造后的污水处理系统实现了污水达标回注,降低了无效回注费用。同时还回收了污油,降低了药剂成本,产生了十分明显的经济效益,每年节约成本约500万元。     

Effects of planned expansion of waste incineration in the Swedish district heating systems

Recent targets for reduced amounts of waste to landfills in Sweden will result in a large increase in waste incineration with recovery of energy, used primarily for district heating. The aim of this study is to investigate what changes in the usage of other fuels and technologies for district heat production would be caused by this increase. A questionnaire was sent out to the largest district heating companies, and simulations in an energy systems model were carried out. The analysis shows that increased waste incineration reduces the demand for other fuels, especially biomass, for district heat production. The effects include reductions in operating hours as well as the avoidance or postponement of investments in new plants for district heat production. Increased waste incineration will also lead to a greater use of district heating in Sweden.     

垃圾焚烧烟气中二(噁)英零排放技术实践

介绍了绍兴新民热电有限公司用煤和垃圾混烧循环流化床技术处理城市生活垃圾，焚烧烟气经活性炭吸附、半干法和布袋除尘器净化工艺处理后，烟气中二噁英接近零排放。     

垃圾焚烧飞灰中重金属的固化/稳定化处理实验研究

研究了城市生活垃圾焚烧-电灰的特性及飞灰中重金属的特性,对利用水泥作粘结剂进行飞灰固化/稳定化处理效果开展了系统的实验研究,分析了水泥固化/稳定化飞灰的工艺特点和最佳工艺参数,并讨论了粘结剂固化飞灰机理以及重金属浸出毒性,为进一步研究城市生活垃圾焚烧飞灰的无害化处理与利用提供了有重要价值的参考依据.     

用微波消解-光度法测定废钻井液中的总铬

采用微波消解-光度法处理钻井液废水中的总铬。该方法克服了常规消解方法的缺点,测定步骤简单、快速,准确性高。通过实验探讨了微波功率、加热时间、样品体积对样品消解的影响。与常压的硫酸-硝酸消解法进行比较的结果表明,用微波消解-光度法处理泥浆废水可将消解时间由原来的6h缩短为20min,加标回收率由60%提高到92%,降低了工作强度,改善了工作环境。     

Pyrolysis technologies for municipal solid waste: A review

Pyrolysis has been examined as an attractive alternative to incineration for municipal solid waste (MSW) disposal that allows energy and resource recovery; however, it has seldom been applied independently with the output of pyrolysis products as end products. This review addresses the state-of-the-art of MSW pyrolysis in regards to its technologies and reactors, products and environmental impacts. In this review, first, the influence of important operating parameters such as final temperature, heating rate (HR) and residence time in the reaction zone on the pyrolysis behaviours and products is reviewed; then the pyrolysis technologies and reactors adopted in literatures and scale-up plants are evaluated. Third, the yields and main properties of the pyrolytic products from individual MSW components, refuse-derived fuel (RDF) made from MSW, and MSW are summarised. In the fourth section, in addition to emissions from pyrolysis processes, such as HCl, SO₂ and NH₃, contaminants in the products, including PCDD/F and heavy metals, are also reviewed, and available measures for improving the environmental impacts of pyrolysis are surveyed. It can be concluded that the single pyrolysis process is an effective waste-to-energy convertor but is not a guaranteed clean solution for MSW disposal. Based on this information, the prospects of applying pyrolysis technologies to dealing with MSW are evaluated and suggested.     

Investigating the effect of compression on solute transport through degrading municipal solid waste

The effect of applied compression on the nature of liquid flow and hence the movement of contaminants within municipal solid waste was examined by means of thirteen tracer tests conducted on five separate waste samples. The conservative nature of bromide, lithium and deuterium tracers was evaluated and linked to the presence of degradation in the sample. Lithium and deuterium tracers were non-conservative in the presence of degradation, whereas the bromide remained effectively conservative under all conditions. Solute diffusion times into and out of less mobile blocks of waste were compared for each test under the assumption of dominantly dual-porosity flow. Despite the fact that hydraulic conductivity changed strongly with applied stress, the block diffusion times were found to be much less sensitive to compression. A simple conceptual model, whereby flow is dominated by sub-parallel low permeability obstructions which define predominantly horizontally aligned less mobile zones, is able to explain this result. Compression tends to narrow the gap between the obstructions, but not significantly alter the horizontal length scale. Irrespective of knowledge of the true flow pattern, these results show that simple models of solute flushing from landfill which do not include depth dependent changes in solute transport parameters are justified.     

CFD simulation of MSW combustion and SNCR in a commercial incinerator

A CFD scheme was presented for modeling municipal solid waste (MSW) combustion in a moving-grate incinerator, including the in-bed burning of solid wastes, the out-of-bed burnout of gaseous volatiles, and the selective non-catalytic reduction (SNCR) process between urea (CO(NH₂)₂) and NO_x. The in-bed calculations provided 2-D profiles of the gas–solid temperatures and the gas species concentrations along the bed length, which were then used as inlet conditions for the out-of-bed computations. The over-bed simulations provided the profiles of incident radiation heat flux on the top of bed. A 3-dimensional benchmark simulation was conducted with a 750 t/day commercial incinerator using the present coupling scheme incorporating with a reduced SNCR reduction mechanism. Numerical tests were performed to investigate the effects of operating parameters such as injection position, injection speed and the normalized stoichiometric ratio (NSR) on the SNCR performance. The simulation results showed that the distributions of gas velocity, temperature and NO_x concentration were highly non-uniform, which made the injection position one of the most sensitive operating parameters influencing the SNCR performance of moving grate incinerators. The simulation results also showed that multi-layer injections were needed to meet the EU2000 standard, and a NSR 1.5 was suggested as a compromise of a satisfactory NO_x reduction and reasonable NH₃ slip rates. This work provided useful guides to the design and operation of SNCR process in moving-grate incinerators.