输氧抽气技术在垃圾填埋场治理中的关键参数试验研究

输氧抽气技术是基于好氧降解原理对垃圾填埋场中固体废弃物实施原位处理的先进环保技术。采用该技术对垃圾填埋场中固体废弃物减量化研究,总结了技术应用中的关键参数:有效影响半径,最佳真空度等。结果表明抽气流量大小与影响半径密切相关,抽气影响半径建议取20~25 m,抽气系统最优负压为20 k Pa,同时在技术应用过程中应保证垃圾场表层覆盖层的密封性能,尽量减少空气的渗入。输氧抽气技术在垃圾场的成功实施为同类型场地治理提供工程技术参考。     

垃圾渗滤液预处理工艺的研究

本文结合工程实例,对生活垃圾焚烧发电厂垃圾渗滤液进行预处理工艺的研究,结果表明,预处理单元在垃圾焚烧厂渗滤液的整个处理系统中具有重要的作用和地位,渗滤液中部分污染物和无机离子能在预处理单元中得到较好的去除,在一定程度上减轻后续处理工艺的负荷。     

臭氧-曝气生物滤池深度处理垃圾焚烧渗滤液可行性研究

研究了臭氧-曝气生物滤池(BAF)代替纳滤和反渗透深度处理垃圾焚烧渗滤液达标排放的技术可行性.半间歇臭氧氧化试验表明,实验用水的可生化性随着氧化时间的增加而增加,色度及UV254, 15min内去除率分别达91%和64%;氧化时间为45min时COD去除率59%, 45min后COD去除较慢, 120min时去除率77%.确定臭氧氧化时间为1h,在同样臭氧浓度与流量下进行了臭氧-BAF处理垃圾焚烧渗滤液的连续实验.结果发现,此工艺对COD、色度和UV254的去除率分别可达75%,95%和90%,其中2/3运行时间里COD低于排放标准100 mg/L.其中出水色度可稳定保持在40度以下达标排放.经过进一步优化,臭氧-BAF有望用于垃圾焚烧渗滤液的达标处理.GC-MS检测表明烷烃,芳香族化合物及含氮杂环化合物是试验用水的主要污染物,臭氧-BAF能够有效去除后两类化合物,但难以去除烷烃.     

Comparative study on the efficiency and environmental impact of two methods of utilizing polyvinyl chloride waste based on life cycle assessments

Two processes of utilizing polyvinyl chloride （PVC） waste, an incineration process and a vacuum pyrolysis process, for energy conversion were compared to determine their efficiency and environmental perfor- mance. We carried out a life cycle assessment with each of the two processes to evaluate their environmental impact and defined the goals and limits of our remit. As well, we established an inventory of PVC waste from incineration and vacuum pyrolysis based on process analysis, data collection and calculations. The results show that electrical power output per unit mass of PVC waste in the incineration process was twice as high as that of the vacuum pyrolysis process. Incineration had a larger total environmental impact potential than vacuum pyrolysis. The total environmental impact potential of PVC waste from incineration was three times higher than that from vacuum pyrolysis. Incineration of PVC disposed 300 ng. 100 kgI of dioxins and vacuum pyrolysis 98.19 ng- 100 kgI of dioxins. As well, we analyzed the data for their uncertainty with results quantified in terms of three uncertainties： basic uncertainty, additional uncertainty, and computational uncertainty. The coefficients of variation of the data were less than 25% and the quality of the inventory data was acceptable with low uncertainty. Both PVC waste disposal processes were of similar quality and their results comparable. The results of our life cycle impact assessment （LCIA） showed considerable reliability of our methodology. Overall, the vacuum pyrolysis process has a number advantages and greater potential for development of PVC disposal than the incineration process.     

两种垃圾焚烧炉灰渣的重金属成分与放射性检测

对8种重金属As、Hg、Mn、Cr、Cu、Cd、Co、Ni和Pb在两种垃圾焚烧炉灰渣中的浓度分布,浸出毒性及放射性进行检测.样品(炉渣和飞灰)分别取自北京(循环流化床焚烧炉CFBI)和深圳(炉排焚烧炉)两台不同燃烧方式的垃圾焚烧炉.研究表明,CFBI炉渣及飞灰中的重金属As、Mn、Cu、Cd、Co含量在炉渣中含量最低,中灰次之,飞灰中含量最高.重金属Hg在炉渣和飞灰中的含量相当,在中灰中的含量最低;Cr和Ni在炉渣中的含量也偏高,在中灰和飞灰中的含量相当Pb含量依中灰、炉渣和飞灰的顺序逐渐升高.浸出毒性检测结果显示,循环流化床垃圾焚烧后炉渣及飞灰中的重金属浸出毒性远低于国家标准1～2个量级,重金属总体排放量较低.炉排炉垃圾焚烧的炉渣及飞灰中的重金属含量却高很多,尤其是Cr、Pb、Cd和Cu.放射性检测结果表明,两种焚烧所产生的灰渣放射性均低于国家标准.在排放时无需作任何放射性方面的处理.最后,对焚烧灰渣的稳定化技术进行了讨论.     

印染污泥焚烧烟气污染控制案例分析

以广东省某两家印染厂的印染污泥焚烧项目为主要研究对象,从污泥处理技术路线、焚烧设备及烟气处理流程等各方面入手,对各厂印染污泥与煤混烧烟气中颗粒物、NOx、SO2、酸性气体(HF、HCl)和重金属等污染物的进行采样分析,并对各厂现有烟气污染物控制设施的运行效果进行调研,结果表明,布袋除尘的效果较为理想,除尘效率可达99%以上;使用印染废水作为吸收液的湿法脱硫技术对SO2及酸性气体的去除效果不理想;SNCR对NOx具有一定的去除效果,是一种较为经济、高效的脱硝技术;焚烧后,大部分重金属最终以飞灰的形式被除尘器去除,但仍有部分重金属如Hg在出口烟气中的浓度仍然很高,需要采取必要的措施控制烟气中的重金属. 此外,基于印染污泥焚烧实例分析,提出适于印染污泥与煤混烧烟气处理工艺流程.     

MESIP∗: Modelling environmental scenarios in ponds

MESIP is a fugacity model which can predict the fate of organic hydrophobic chemicals in aquatic ecosystems. In this paper a short introduction to the mathematical model is presented together with a more detailed listing of the required input data. Comparison of the calculated and measured fate of a fluorescent whitening compound in an artificial outdoor pond is shown     

我国生活垃圾焚烧二恶英污染现状及减排建议

生活垃圾焚烧的二恶英污染问题在我国已经引起全社会的广泛关注。在分析我国生活垃圾焚烧行业现状与发展趋势和我国部分焚烧厂二恶英排放情况的基础上,提出了我国生活垃圾焚烧二恶英污染防治和减排的建议。     

Municipal solid waste management in Dalian: practices and challenges

The fast growing of urban areas in developing countries has brought serious problems on municipal solid waste (MSW) management. It will be rational to adopt an integrated approach to deal with such a challenge so that the overall eco-efficiency of MSW management could be improved. To better examine how attributes of integrated MSW management are being interpreted and put into practice, and to explore what changes should be made to improve the application of integrated MSW management, we employ a case study method so that lessons learned could be used to inform initiatives in other cities and the potential solution may offer feasible strategies. The case study city is Dalian, a typical seaport city with fast growing rate in economy. The outcomes of this case study show us that fragmented management structure, ineffective and inefficient enforcement of relevant regulations, backward technologies, limited financial resources and lack of public participation are main barriers for the implementation of integrated MSW management. Consequently, in order to overcome these barriers, we propose an integrated management framework on MSW management, aiming to maximize the overall eco-efficiency of MSW management.     

中国城市垃圾典型可行焚烧技术的综合评价

中国城市垃圾处理的主要方式正在由卫生填埋向垃圾焚烧转变. 基于中国城市垃圾焚烧处置需求特征分析,建立了技术评价指标体系,采用层次分析法,从技术的可靠性、经济性和适用性三方面,对国内外现有4种主要城市垃圾焚烧技术进行了综合评价. 结果表明:流化床技术和层燃技术在技术成熟度、技术能力和二NFDA1英污染控制等方面相对可靠,适用于我国多数大城市的垃圾焚烧处置. 国产流化床焚烧技术更加适应当前国内垃圾分类水平较差的大部分城市;层状焚烧技术则比较适用于城市垃圾管理水平高、垃圾分类较好、热值较高、垃圾处置集中度高和规模较大的城市;旋转焚烧和热解焚烧技术则较适用于垃圾成分复杂、尺寸不均匀的小城镇、工业园区垃圾处置或医疗废物处置,但二者均需加强二NFDA1英排放控制.