普通活性污泥膜生物反应器处理洗车废水的应用研究

膜生物反应器是近年来发展起来的一种新型高效水处理设备。它将分离工程中的膜技术应用于好氧活性污泥处理系统，由膜组件取代传统生化处理技术中的二次沉淀池和砂滤池，由膜分离技术代替传统方法中的重力式沉淀泥水分离技术方式，具有简洁、高效等优点。采用普通活性污泥膜生物反应器工艺对天津某一洗车点洗车废水进行处理，并将处理出水回用于洗车。     

曝气强度对膜污染的影响

混合液浓度的高低及其粒度分布特性是影响膜生物反应器膜污染的重要因素。在一定污泥浓度下,主要考察了曝气强度对污泥絮体粒度分布的影响,以及不同粒度下的膜污染特性。试验结果表明,曝气强度提高,可以起到减缓污泥颗粒在膜表面的沉积作用,但高的错流流速产生的剪切效应使得污泥颗粒变得琐碎,导致细小胶体粒子和溶解性部分增多,增加了膜孔吸附和堵塞的机会,加剧了膜污染的进程。膜污染速率在曝气强度提高初期阶段迅速降低,接着又随曝气强度增加而缓慢升高,在污泥质量浓度为8 g/L的试验条件下,对应的最适曝气强度为84 m3/(m2.h)。     

Performance and fouling mechanism of direct contact membrane distillation (DCMD) treating fermentation wastewater with high organic concentrations

In this study,direct contact membrane distillation(DCMD)was used for treating fermentation wastewater with high organic concentrations.DCMD performance characteristics including permeate flux,permeate water quality as well as membrane fouling were investigated systematically.Experimental results showed that,after 12 hr DCMD,the feed wastewater was concentrated by about a factor of 3.7 on a volumetric basis,with the permeate flux decreasing from the initial 8.7 L/m~2/hr to the final 4.3 L/m~2/hr due to membrane fouling;the protein concentration in the feed wastewater was increased by about 3.5 times and achieved a value of 6178 mg/L,which is suitable for reutilization.Although COD and TOC in permeate water increased continuously due to the transfer of volatile components from wastewater,organic rejection of over 95%was achieved in wastewater.GC–MS results suggested that the fermentation wastewater contained 128kinds of organics,in which 14 organics dominated.After 12 hr DCMD,not only volatile organics including trimethyl pyrazine,2-acetyl pyrrole,phenethyl alcohol and phenylacetic acid,but also non-volatile dibutyl phthalate was detected in permeate water due to membrane wetting.FT-IR and SEM–EDS results indicated that the deposits formed on the membrane inner surface mainly consisted of Ca,Mg,and amine,carboxylic acid and aromatic groups.The fouled membrane could be recovered,as most of the deposits could be removed using a HCl/Na OH chemical cleaning method.     

废弃含汞灯具中荧光粉分析及汞处理

废旧直管型荧光灯、节能灯及高压汞灯等照明灯具所用荧光粉中含有重金属汞,由此带来的汞污染已危及人体健康与生态安全。分析了废弃含汞灯具中荧光粉混合物的粒径分布以及不同粒径筛分物中塑料的组分含量和汞含量,并研究了不同加热时间、加热温度对汞蒸馏效果的影响。结果表明:含汞荧光粉原料中塑料含量占1.00%,粒径大于150μm的玻璃颗粒占72.00%以上,其汞含量仅为9 mg/kg;在恒定氮气量为2L/min的条件下,利用管式炉在700℃的温度下加热240min,汞的蒸馏效果最佳,汞蒸馏效率为61.11%~95.26%。     

Influence of osmotic distillation on membrane absorption for the treatment of high strength ammonia wastewater

Osmotic distillation (OD) was found to be a coupled process in membrane absorption (MA) for the treatment of high strength ammonia wastewater. As a result, ammonia could not be concentrated in absorption solution(AS) as expected. The inhibition of the coupled OD in MA process was investigated as well as various factors affecting the inhibition. The results indicated that the coupled OD can be effectively inhibited by heating concentrated solution and cooling dilute solution. It was also found that experimental minimum inhibition temperature difference(MITD) between concentrated and dilute solutions was different when using polyvinylidene fluoride(PVDF) and polypropylene(PP) membranes respectively, which could be ascribed to material properties, such as OD and membrane distillation (MD) coefficients of the membranes. Experimental MITDs were found to be higher than theoretical MITDs which were calculated using a simplified method.     

Improved blending strategy for membrane modification by virtue of surface segregation using surface-tailored amphiphilic nanoparticles

Membrane modification is one of the most feasible and effective solutions to membrane fouling problem which tenaciously hampers the further augmentation of membrane separation technology. Blending modification with nanoparticles (NPs), owing to the convenience of being incorporated in established membrane production lines, possesses an advantageous viability in practical applications. However, the existing blending strategy suffers from a low utilization efficiency due to NP encasement by membrane matrix. The current study proposed an improved blending modification approach with amphiphilic NPs (aNPs), which were prepared through silanization using 3-(Trimethoxysilyl)propyl methacrylate (TMSPMA) as coupling agents and ZnO or SiO₂ as pristine NPs (pNPs), respectively. The Fourier transform infrared and X-ray photoelectron spectroscopy analyses revealed the presence of appropriate organic components in both the ZnO and SiO₂ aNPs, which verified the success of the silanization process. As compared with the pristine and conventional pNP-blended membranes, both the ZnO aNP-blended and SiO₂ aNP-blended membranes with proper silanization (100% and 200%w/w) achieved a significantly increased blending efficiency with more NPs scattering on the internal and external membrane surfaces under scanning electron microscope observation. This improvement contributed to the increase of membrane hydrophilicity. Nevertheless, an extra dosage of the TMSPMA led to an encasement of NPs, thereby adversely affecting the properties of the resultant membranes. On the basis of all the tests, 100% (w/w) was selected as the optimum TMSPMA dosage for blending modification for both the ZnO and SiO₂ types.

Open image in new window

     

轧钢污泥综合利用的技术研究

阐述了一种轧钢污泥的回收处理技术,该技术可把轧钢污泥有效地分离成氧化铁粉和混合油,实现综合利用,减少铁素资源浪费,有良好的经济效益和环境效益.     

Effect of iron addition on the performance of anoxic-oxic membrane process and biological phosphorus removal北大核心CSCD

In order to solve the problem of poor treatment of phosphorus in membrane bioreactor (MBR) with long sludge retention time (SRT), a ferric salt was added to enhance phosphorus removal; FeCl36H2O (Fe/P = 2.0) was added to the reactor. The removal efficiency of nitrogen, organic matters, and phosphorus in the MBR was investigated systematically. Moreover, this study focused on the membrane performance, the change of active sludge flora, and the effect of adding a ferric salt on membrane fouling before and after the addition. It was seen that adding the ferric salt could not affect the removal of COD and NH4 +-N and the removal rate of COD and NH4 +-N reached over 90%. However, the average removal rate of phosphorus was 52%, while the removal rate increased by nearly 40% after adding the ferric salt. The effects of adding ferric salts on the dominant bacteria and biological phosphorus removal of activated sludge were further studied. The results showed that the addition of ferric salt (Fe/P = 2.0) decreased the diversity of active sludge flora and relative abundance of some phosphorusaccumulating organisms and had a negative effect on biological phosphorus removal. The analysis of transmembrane pressure difference (TMP) recording revealed that the concentration of iron salts did not exacerbate membrane fouling. The results showed that the concentration of iron salts entering the membrane bioreactor would reduce the relative abundance and phosphorus removal efficiency of the activated sludge in the system to a certain extent, but it had no obvious effect on membrane fouling. It allowed the effluent to attain acceptable standards, especially with respect to phosphorus removal efficiency. © 2018 Science Press. All rights reserved.     

Comparison of membrane fouling in ultrafiltration of down-flow and up-flow biological activated carbon effluents

The UF membrane fouling by down- and up-flow BAC effluents were compared. Up-flow BAC effluent fouled the membrane faster than down-flow BAC effluent. The combined effects dominated irreversible fouling. The extent of fouling exacerbated by inorganic particles was higher. The TMP, permeate flux, and normalized membrane flux during 21 days of UF of DBAC and UBAC effluents. Fouling during ultrafiltration of down- and up-flow biological activated carbon effluents was investigated to determine the roles of polysaccharides, proteins, and inorganic particles in ultrafiltration membrane fouling. During ultrafiltration of down- flow biological activated carbon effluent, the trans-membrane pressure was≤26 kPa and the permeate flux was steady at 46.7 L?m⁻²?h⁻¹. However, during ultrafiltration of up-flow biological activated carbon effluent, the highest trans-membrane pressure was almost 40 kPa and the permeate flux continuously decreased to 30 L?m⁻²?h⁻¹. At the end of the filtration period, the normalized membrane fluxes were 0.88 and 0.62 for down- and up-flow biological activated carbon effluents, respectively. The membrane removed the turbidity and polysaccharides content by 47.4% and 30.2% in down- flow biological activated effluent and 82.5% and 22.4% in up-flow biological activated carbon effluent, respectively, but retained few proteins. The retention of polysaccharides was higher on the membrane that filtered the down- flow biological activated effluent compared with that on the membrane that filtered the up-flow biological activated carbon effluent. The polysaccharides on the membranes fouled by up-flow biological activated carbon and down- flow biological activated effluents were spread continuously and clustered, respectively. These demonstrated that the up-flow biological activated carbon effluent fouled the membrane faster. Membrane fouling was associated with a portion of the polysaccharides (not the proteins) and inorganic particles in the feed water. When there was little difference in the polysaccharide concentrations between the feed waters, the fouling extent was exacerbated more by inorganic particles than by polysaccharides.     

Energy reduction of a submerged membrane bioreactor using a polytetrafluoroethylene (PTFE) hollow-fiber membrane

The fiber length and packing density of the PTFE membrane element were increased. The MBR was stably operated under an SAD^m of 0.13 m³·m^-2·hr^-1. Specific energy consumption was estimated to be less than 0.4 kWh·m^-3. In this study, we modified a polytetrafluoroethylene (PTFE) hollow-fiber membrane element used for submerged membrane bioreactors (MBRs) to reduce the energy consumption during MBR processes. The high mechanical strength of the PTFE membrane made it possible to increase the effective length of the membrane fiber from 2 to 3 m. In addition, the packing density was increased by 20% by optimizing the membrane element configuration. These modifications improve the efficiency of membrane cleaning associated with aeration. The target of specific energy consumption was less than 0.4 kWh·m^-3 in this study. The continuous operation of a pilot MBR treating real municipal wastewater revealed that the MBR utilizing the modified membrane element can be stably operated under a specific air demand per membrane surface area (SAD_m) of 0.13 m³·m^-2·hr^-1 when the daily-averaged membrane fluxes for the constant flow rate and flow rate fluctuating modes of operation were set to 0.6 and 0.5 m³·m^-2·d^-1, respectively. The specific energy consumption under these operating conditions was estimated to be less than 0.37 kWh·m^-3. These results strongly suggest that operating an MBR equipped with the modified membrane element with a specific energy consumption of less than 0.4 kWh·m^-3 is highly possible.