The biological effect of metal ions on the granulation of aerobic granular activated sludge

As a special biofilm structure, microbial attachment is believed to play an important role in the granulation of aerobic granular activated sludge (AGAS). This experiment was to investigate the biological effect of Ca^2 +, Mg^2 +, Cu^2 +, Fe^2 +, Zn^2 +, and K⁺ which are the most common ions present in biological wastewater treatment systems, on the microbial attachment of AGAS and flocculent activated sludge (FAS), from which AGAS is always derived, in order to provide a new strategy for the rapid cultivation and stability control of AGAS. The result showed that attachment biomass of AGAS was about 300% higher than that of FAS without the addition of metal ions. Different metal ions had different effects on the process of microbial attachment. FAS and AGAS reacted differently to the metal ions as well, and in fact, AGAS was more sensitive to the metal ions. Specifically, Ca^2 +, Mg^2 +, and K⁺ could increase the microbial attachment ability of both AGAS and FAS under appropriate concentrations, Cu^2 +, Fe^2 +, and Zn^2 + were also beneficial to the microbial attachment of FAS at low concentrations, but Cu^2 +, Fe^2 +, and Zn^2 + greatly inhibited the attachment process of AGAS even at extremely low concentrations. In addition, the acylated homoserine lactone (AHL)-based quorum sensing system, the content of extracellular polymeric substances and the relative hydrophobicity of the sludges were greatly influenced by metal ions. As all these parameters had close relationships with the microbial attachment process, the microbial attachment may be affected by changes of these parameters.     

The role of lipids in fermentative propionate production from the co-fermentation of lipid and food waste

● Lipid can promote PA production on a target from food waste. ● PA productivity reached 6.23 g/(L∙d) from co-fermentation of lipid and food waste. ● Lipid promoted the hydrolysis and utilization of protein in food waste. ● Prevotella , Veillonella and norank _f _Propioni bacteriaceae were enriched. ● Main pathway of PA production was the succinate pathway. Food waste (FW) is a promising renewable low-cost biomass substrate for enhancing the economic feasibility of fermentative propionate production. Although lipids, a common component of food waste, can be used as a carbon source to enhance the production of volatile fatty acids (VFAs) during co-fermentation, few studies have evaluated the potential for directional propionate production from the co-fermentation of lipids and FW. In this study, co-fermentation experiments were conducted using different combinations of lipids and FW for VFA production. The contributions of lipids and FW to propionate production, hydrolysis of substrates, and microbial composition during co-fermentation were evaluated. The results revealed that lipids shifted the fermentation type of FW from butyric to propionic acid fermentation. Based on the estimated propionate production kinetic parameters, the maximum propionate productivity increased significantly with an increase in lipid content, reaching 6.23 g propionate/(L∙d) at a lipid content of 50%. Propionate-producing bacteria Prevotella, Veillonella, and norank_f_Propionibacteriaceae were enriched in the presence of lipids, and the succinate pathway was identified as a prominent fermentation route for propionate production. Moreover, the Kyoto Encyclopedia of Genes and Genomes functional annotation revealed that the expression of functional genes associated with amino acid metabolism was enhanced by the presence of lipids. Collectively, these findings will contribute to gaining a better understanding of targeted propionate production from FW.     

Recent advances in three typical configurations and applications of bioelectrochemical systems北大核心CSCD

As the world's freshwater resources and available energy are alarmingly decreasing, the bioelectrochemical system (BES) is a cutting-edge technology for the resolution of the resource and energy issue. Researchers have paid much attention to t he application of t he BES configuration. Based on t he brief i ntroduction of m icrobial f uel cell a nd m icrobial electrolytic cell structure, principles, and domestic and foreign research, the BES and its influencing factors are introduced, specifically including: microbial activity, electrode materials, and configuration. Three important aspects (i.e., the electrode chamber, the reaction chamber, and micro-sensor) are summarized, and the advantages and disadvantages of single-electrode and multi-electrode chambers are compared, based on the microbial desalination cell. Microbial electrolysis desalination cell: Microbial electrolysis desalination and chemical-production cell have been discussed to introduce increasing reaction chamber configuration; this review focuses on the research of BES monitoring with regards to biochemical oxygen demand. The potential applications of the research progress are explored. The results show that the configuration of multi-chamber microbial fuel cell is complex and its efficiency is low, while the single chamber configuration is advantageous. The reaction chamber added is mainly aimed at desalination, and the study of the desalination pool still needs to be focused on optimizing the cation exchange membrane to maintain the anode pH balance and reduce the air cathode dissolved oxygen. Microbial electrode sensor can be applied in more areas, and its sensitivity and long-term stability need to be further improved. However, there is relatively less research on the abundance and activity of electricigen communities; the configurations and scopes of application of BES are still the research priority. © 2018 Science Press. All rights reserved.     

Effect of iron addition on the performance of anoxic-oxic membrane process and biological phosphorus removal北大核心CSCD

In order to solve the problem of poor treatment of phosphorus in membrane bioreactor (MBR) with long sludge retention time (SRT), a ferric salt was added to enhance phosphorus removal; FeCl36H2O (Fe/P = 2.0) was added to the reactor. The removal efficiency of nitrogen, organic matters, and phosphorus in the MBR was investigated systematically. Moreover, this study focused on the membrane performance, the change of active sludge flora, and the effect of adding a ferric salt on membrane fouling before and after the addition. It was seen that adding the ferric salt could not affect the removal of COD and NH4 +-N and the removal rate of COD and NH4 +-N reached over 90%. However, the average removal rate of phosphorus was 52%, while the removal rate increased by nearly 40% after adding the ferric salt. The effects of adding ferric salts on the dominant bacteria and biological phosphorus removal of activated sludge were further studied. The results showed that the addition of ferric salt (Fe/P = 2.0) decreased the diversity of active sludge flora and relative abundance of some phosphorusaccumulating organisms and had a negative effect on biological phosphorus removal. The analysis of transmembrane pressure difference (TMP) recording revealed that the concentration of iron salts did not exacerbate membrane fouling. The results showed that the concentration of iron salts entering the membrane bioreactor would reduce the relative abundance and phosphorus removal efficiency of the activated sludge in the system to a certain extent, but it had no obvious effect on membrane fouling. It allowed the effluent to attain acceptable standards, especially with respect to phosphorus removal efficiency. © 2018 Science Press. All rights reserved.     

基于活性污泥微生物冻后再生对废水基质降解效能的研究

采用高径比为12.5的序批式反应器(SBR)对冷冻的成熟好氧颗粒污泥（AGS）解冻驯化,研究母体颗粒冻后富集培养及其在番茄废水基质降解中的循环利用。结果表明：冻后恢复活性的污泥第60天全部颗粒化,平均粒径不小于0.45 mm;高通量测序结果显示,相较母体颗粒,该污泥中与颗粒化相关的变形菌门(Proteobacteria)和拟杆菌门(Bacteroidetes)优势菌群富集,微生物丰度呈显著差异（P<0.05）;复合菌株对COD、NH3-N和PO3-4-P去除率分别为98.9%、82.1%和82.2%,可实现番茄废水的有效降解。     

Prevalence of Musculoskeletal Disorders at Workplaces in the People’s Republic of China

This paper presents 2 musculoskeletal disorders questionnaire surveys in 10 different Chinese occupational groups. Data collected from 1,603 workers using a modified Nordic musculoskeletal disorders symptom questionnaire showed that the 12-month prevalence of musculoskeletal disorders, particularly in the low back and shoulder-neck regions, was high at many Chinese workplaces. Significant differences existed between occupational groups. Assembly workers usually had higher neck-shoulder complaints compared to workers in most other occupations. However, the nature of assembly seemed also to influence the prevalence rate. Workers at a cassette recorder and a TV set assembly plant appeared to have more neck complaints compared with a group of thermos flask assemblers.     

Postural Loading Assessment in Assembly Workers of an Iranian Telecommunication Manufacturing Company

Background. Changes in industries and work practices have coincided with work-related musculoskeletal disorders (MSDs). This study was conducted to determine the prevalence of MSDs and to assess postural loading in assembly workers of an Iranian telecommunication manufacturing company. Methods. Data were collected from 193 randomly selected workers in 4 units of the company. The Nordic musculoskeletal disorders questionnaire and the UBC ergonomic checklist were used as data collection tools. Loading on the upper body assessment (LUBA) was used to assess postural loading. Results. Lower back symptoms were the most prevalent problems among the workers (67.9%). LUBA showed that most assembly workers (94.3%) had experienced considerable and high postural loading (postural load index, PLI > 5). Regression analyses revealed that lighting, rotation, contact stress, repetition, gender and age were factors associated with symptoms. Conclusion. Work-related MSDs occurred at a high rate among workers. Postural loading requires consideration. Any ergonomic intervention should focus on eliminating ergonomic factors associated with symptoms.     

Ergonomic analysis of working postures using OWAS in semi-trailer assembly,applying an individual sampling strategy

In semi-trailer assembly, workers are exposed to several physical risk factors. Awkward working postures have not yet been investigated in semi-trailer assembly, although they are known to be a major risk factor for musculoskeletal disorders. We therefore conducted a comprehensive ergonomic analysis of working postures using the Ovako working posture analysing system (OWAS), with an individual sampling strategy. The postural load in semi-trailer assembly was assessed on the basis of 20,601 observations of 63 workers executing a representative set of nine work tasks. According to the OWAS, the postural load of various working postures and body part positions may have a harmful effect on the musculoskeletal system. We therefore give examples of corrective measures that could improve awkward working postures. Applying an individual sampling strategy was revealed to have advantages over a collective strategy, so this is recommended for future ergonomic analyses.     

Applying CES to assembly and comparing carbon footprints

A Carbon Emission Signature (CES) and a Carbon Emission Label have been proposed for manufactured products in previous CIRP (Collège International pour la Recherche en Productique) annals. This paper considers two things: (1) an example of a CES calculation for assembly with CO₂ emissions and (2) the need for a transparent method of calculation. In comparing carbon footprint calculations for 17 websites, the results are found to vary more than threefold depending upon the site used and even more between different methods illustrating the need for standardisation in emission calculations for carbon accounting.     

Assembly operator training and process planning via virtual systems

In this paper, we present an integrated intuitive system for assembly operators training and assembly process planning by combining virtual reality with motion-tracking technologies. The developed conceptual prototype for assembly planning and training enables individuals to interact with a virtual environment in real time. It extends the new technologies of motion tracking and integrates them with virtual environment technologies to create real-time virtual work cell simulations in which assembly operators may be immersed with hands-on experiences. In addition to operators training, the experimental results to date are presented to demonstrate the potential contributions of human skills in achieving effective assembly planning including disassembly operations. It is expected that this approach will lead to environment-friendly and sustainable operations by conserving energy and cost that are first tested in a human-emerged virtual system.