Selective collection as a pretreatment for indirect solid recovered fuel generation

Effective selective collection (SC) has been increasing in many countries of the European Union. As a consequence the composition of residual municipal solid waste (RMSW) is changing not only because of economic development, but also due to the collection system. The input of RMSW treatment plants is thus not homogeneous. This paper analyses two case studies involving a total of five SC scenarios and their impact on the generation of solid recovered fuel (SRF) with/without bio-drying, post-treatment and packaging take back programs (TBPs). These case studies are based on two types of SC: kerbside and drop-off. The latest regulation on SRF classification is taken into account: energy content, Cl and Hg concentrations are assessed and discussed. The role of the respirometric index (RI) is also analyzed. Results show that when SC is highly efficient RMSW can be classified directly as SRF, but only if the introduction of RI does not set stringent respirometric targets. The role of packaging TBPs is important as the residual waste remaining after the packaging has been processed, can be valorized increasing the lower heating value (LHV) of the residual RMSW and minimizing the streams that should be landfilled. The source separation of food waste has a significant impact on the suitability of bio-drying: when the SC of food waste is very efficient, its percentage in the RMSW may be too low for effective bio-drying.     

Oxygen demand for the stabilization of the organic fraction of municipal solid waste in passively aerated bioreactors

Conventional aerobic waste treatment technologies require the use of aeration devices that actively transport air through the stabilized waste mass, which greatly increases operating costs. In addition, improperly operated active aeration systems, may have the adverse effect of cooling the stabilized biomass. Because active aeration can be a limiting factor for the stabilization process, passive aeration can be equally effective and less expensive. Unfortunately, there are few reports documenting the use of passive aeration systems in municipal waste stabilization. There have been doubts raised as to whether a passive aeration system provides enough oxygen to the organic matter mineralization processes. In this paper, the effectiveness of aeration during aerobic stabilization of four different organic fractions of municipal waste in a reactor with an integrated passive ventilation system and leachate recirculation was analyzed. For the study, four fractions separated by a rotary screen were chosen. Despite the high temperatures in the reactor, the air flow rate was below 0.016 m³/h. Using Darcy’s equation, theoretical values of the air flow rate were estimated, depending on the intensity of microbial metabolism and the amount of oxygen required for the oxidation of organic compounds. Calculations showed that the volume of supplied air exceeded the microorganisms demand for oxidation and endogenous activity by 1.7–2.88-fold.     

Pyrolysis technologies for municipal solid waste: A review

Pyrolysis has been examined as an attractive alternative to incineration for municipal solid waste (MSW) disposal that allows energy and resource recovery; however, it has seldom been applied independently with the output of pyrolysis products as end products. This review addresses the state-of-the-art of MSW pyrolysis in regards to its technologies and reactors, products and environmental impacts. In this review, first, the influence of important operating parameters such as final temperature, heating rate (HR) and residence time in the reaction zone on the pyrolysis behaviours and products is reviewed; then the pyrolysis technologies and reactors adopted in literatures and scale-up plants are evaluated. Third, the yields and main properties of the pyrolytic products from individual MSW components, refuse-derived fuel (RDF) made from MSW, and MSW are summarised. In the fourth section, in addition to emissions from pyrolysis processes, such as HCl, SO₂ and NH₃, contaminants in the products, including PCDD/F and heavy metals, are also reviewed, and available measures for improving the environmental impacts of pyrolysis are surveyed. It can be concluded that the single pyrolysis process is an effective waste-to-energy convertor but is not a guaranteed clean solution for MSW disposal. Based on this information, the prospects of applying pyrolysis technologies to dealing with MSW are evaluated and suggested.     

Comparative assessment of municipal sewage sludge incineration,gasification and pyrolysis for a sustainable sludge-to-energy management in Greece

For a sustainable municipal sewage sludge management, not only the available technology, but also other parameters, such as policy regulations and socio-economic issues should be taken in account. In this study, the current status of both European and Greek Legislation on waste management, with a special insight in municipal sewage sludge, is presented. A SWOT analysis was further developed for comparison of pyrolysis with incineration and gasification and results are presented. Pyrolysis seems to be the optimal thermochemical treatment option compared to incineration and gasification. Sewage sludge pyrolysis is favorable for energy savings, material recovery and high added materials production, providing a ‘zero waste’ solution. Finally, identification of challenges and barriers for sewage sludge pyrolysis deployment in Greece was investigated.     

Alternative management structures for municipal waste collection services: The influence of economic and political factors

Identifying and characterising the factors that determine why a local authority opts for a particular way of managing its waste collection service is an important issue, warranting research interest in the field of municipal solid waste (MSW) management. This paper presents empirical evidence spanning a broad time horizon (2002–2010) showing that economic and political factors impact in different ways on the provision of waste management services. We examine five alternatives in this area, including public and private service delivery formulas and, within each field, individual and joint options. Our findings highlight the importance of the service cost and that of the various indicators of fiscal stress as determinant factors of management decisions regarding the provision of MSW management services.     

Full-scale blending treatment of fresh MSWI leachate with municipal wastewater in a wastewater treatment plant

Fresh leachate, generated in municipal solid waste incineration (MSWI) plants, contains various pollutants with extremely high strength organics, which usually requires expensive and complex treatment processes. This study investigated the feasibility of blending treatment of MSWI leachate with municipal wastewater. Fresh MSWI leachate was pretreated by coagulation–flocculation with FeCl₃ 2 g/L and CaO 25 g/L, plate-and-frame filter press, followed by ammonia stripping at pH above 12. After that, blending treatment was carried out in a full-scale municipal wastewater treatment plant (WWTP) for approximately 3 months. Different operational modes consisting of different pretreated leachate and methanol addition levels were tested, and their performances were evaluated. Results showed that throughout the experimental period, monitored parameters in the WWTP effluent, including COD (<60 mg/L), BOD₅ (<20 mg/L), ammonium (<8 mg/L), phosphorus (<1.5 mg/L) and heavy metals, generally complied with the Chinese sewage discharged standard. Under the experimental conditions, a certain amount of methanol was needed to fulfill TN removal. An estimation of the operation cost revealed that the expenditure of blending treatment was much lower than the total costs of respective treatment of MSWI leachate and municipal wastewater. The outcomes indicated that blending treatment could not only improve the treatability of the MSWI leachate, but also reduce the treatment cost of the two different wastewaters.     

CFD simulation of MSW combustion and SNCR in a commercial incinerator

A CFD scheme was presented for modeling municipal solid waste (MSW) combustion in a moving-grate incinerator, including the in-bed burning of solid wastes, the out-of-bed burnout of gaseous volatiles, and the selective non-catalytic reduction (SNCR) process between urea (CO(NH₂)₂) and NO_x. The in-bed calculations provided 2-D profiles of the gas–solid temperatures and the gas species concentrations along the bed length, which were then used as inlet conditions for the out-of-bed computations. The over-bed simulations provided the profiles of incident radiation heat flux on the top of bed. A 3-dimensional benchmark simulation was conducted with a 750 t/day commercial incinerator using the present coupling scheme incorporating with a reduced SNCR reduction mechanism. Numerical tests were performed to investigate the effects of operating parameters such as injection position, injection speed and the normalized stoichiometric ratio (NSR) on the SNCR performance. The simulation results showed that the distributions of gas velocity, temperature and NO_x concentration were highly non-uniform, which made the injection position one of the most sensitive operating parameters influencing the SNCR performance of moving grate incinerators. The simulation results also showed that multi-layer injections were needed to meet the EU2000 standard, and a NSR 1.5 was suggested as a compromise of a satisfactory NO_x reduction and reasonable NH₃ slip rates. This work provided useful guides to the design and operation of SNCR process in moving-grate incinerators.     

Case study of landfill leachate recirculation using small-diameter vertical wells

A case study of landfill liquids addition using small diameter (5 cm) vertical wells is reported. More than 25,000 m³ of leachate was added via 134 vertical wells installed 3 m, 12 m, and 18 m deep over five years in a landfill in Florida, US. Liquids addition performance (flow rate per unit screen length per unit liquid head) ranged from 5.6 × 10^?8 to 3.6 × 10^?6 m³ s^?1 per m screen length per m liquid head. The estimated radial hydraulic conductivity ranged from 3.5 × 10^?6 to 4.2 × 10^?4 m s^?1. The extent of lateral moisture movement ranged from 8 to 10 m based on the responses of moisture sensors installed around vertical well clusters, and surface seeps were found to limit the achievable liquids addition rates, despite the use of concrete collars under a pressurized liquids addition scenario. The average moisture content before (51 samples) and after (272 samples) the recirculation experiments were 23% (wet weight basis) and 45% (wet weight basis), respectively, and biochemical methane potential measurements of excavated waste indicated significant (p < 0.025) decomposition.     

Metal distribution characteristic of MSWI bottom ash in view of metal recovery

Bottom ash is the major by-product of municipal solid waste incineration(MSWI), and is often reused as an engineering material, such as road-base aggregate. However, some metals(especially aluminum) in bottom ash can react with water and generate gas that could cause expansion and failure of products containing the ash; these metals must be removed before the ash is utilized. The size distribution and the chemical speciation of metals in the bottom ash from two Chinese MSWI plants were examined in this study, and the recovery potential of metals from the ash was evaluated. The metal concentrations in these bottom ashes were lower than that generated in other developed countries. Specifically, the contents of Al,Fe, Cu and Zn were 18.9–29.2, 25.5–32.3, 0.7–1.0 and 1.6–2.5 g/kg, respectively. Moreover,44.9–57.0 wt.% of Al and 55.6–75.4 wt.% of Fe were distributed in bottom ash particles smaller than 5 mm. Similarly, 46.6–79.7 wt.% of Cu and 42.9–74.2 wt.% of Zn were concentrated in particles smaller than 3 mm. The Fe in the bottom ash mainly existed as hematite, and its chemical speciation was considered to limit the recovery efficiency of magnetic separation.     

好氧MBBR处理含吲哚废水的工艺优化试验研究

为了处理制药企业废水中吲哚类有机污染物,采用好氧MBBR(移动床生物膜反应器)工艺对含吲哚废水进行了试验研究,通过考察HRT、曝气量、吲哚冲击负荷等工艺条件对吲哚、COD和NH_4~+-N等去除效果的影响,确定了好氧MBBR反应器的最佳工艺条件。实验结果表明,在HRT在6~18 h变化时,MBBR工艺对吲哚去除率在8 h以上时达到100%,COD去除率在8 h达到89.65%,而NH_4~+-N去除率在12 h达到最高。在曝气量为0.1~0.12 m L/min时,MBBR工艺对COD和NH_4~+-N去除率分别为88.88%~92.95%和65%~66.83%。进水吲哚浓度25~65 mg/L变化时,好氧MBBR对吲哚去除率保持在100%,而对COD和NH_4~+-N去除率也保持在80%和40%以上,表明好氧MBBR工艺在处理难降解有机污染物方面具有显著优势。