从废甲醇合成催化剂中回收铜锌

将废RK-05甲醇合成催化剂经过煅烧、浸取、精制等工序回收其中的铜和锌。经正交实验得到煅烧废催化剂的最优工艺参数为:废催化剂筛目100目,煅烧温度950℃,煅烧时间60 min。最佳浸取工艺条件为:废催化剂加入量约4 g/L,浸取温度75℃,浸取剂用量与理论用量体积比2.0~3.0,浸取剂浓度4.0 mol/L,浸取时间10min。精制工序制备CuO的最佳工艺条件为:锌粒与滤渣质量比为1.00,反应时间3 h,煅烧温度450℃,煅烧时间4 h。制备ZnO的最佳工艺条件为:煅烧温度800℃,煅烧时间60 min。回收的产品CuO纯度为99.1%,满足GB/T674—2003《化学试剂粉状氧化铜》中优级品的标准。回收的产品ZnO纯度为99.6%,满足GB/T3185—1992《氧化锌(间接法)》中一级品的标准。     

CO_2氢化催化剂研究进展及应用前景分析

由于CO_2在热力学上的稳定性和动力学上的惰性,高效催化剂被广泛应用于CO_2催化氢化反应以实现CO_2的资源化利用。本文主要从催化剂的制备方法、结构特性以及实验条件优化等角度综述了Ni基催化剂、Cu基催化剂和贵金属催化剂在CO_2催化氢化领域的研究进展,并指出了目前研究成果中存在的不足和今后的研究建议。     

Production of bio-oil from algal biomass and its upgradation to biodiesel using CaO-based heterogeneous catalysts

The present article deals with the production of bio-oil from algal biomass as well as the preparation and characterization of noble CaO-based heterogeneous catalyst for upgradation of bio-oil to biodiesel. The bio-oil has been extracted from algal biomass using hexane as solvent in soxhlet apparatus and upgraded to biodiesel by transesterification using noble CaO-based heterogeneous catalysts. Catalyst with TiO₂:CaO molar ratio of 0.25 and calcination temperature of 700°C has been found to be most suitable among all the catalysts developed. Characterization of the catalysts has been done by using X-ray diffraction (XRD), scanning electron microscope (SEM), and thermo-gravimetric analysis (TGA). The input--output model has been developed to correlate experimental and predicted value of biodiesel yield. Optimization of process parameters has been done using response surface methodology. Various properties and elemental composition of algal bio-oil and biodiesel have been determined and compared with biodiesel.     

纳米α-MnO2催化臭氧氧化降解水中双酚A

采用水热法制备了纳米α-MnO₂催化剂,并通过XRD和SEM技术对催化剂的成分和形貌进行了表征。采用纳米α-MnO₂催化剂催化臭氧氧化降解水中的双酚A（BPA）,考察了初始溶液pH、催化剂加入量和反应温度对BPA去除率的影响。实验结果表明,纳米α-MnO₂催化剂催化臭氧氧化降解BPA的最佳工艺条件为：催化剂加入量100 mg/L,初始溶液pH 8.5,反应温度18 ℃。在此最佳条件下处理质量浓度为10 μg/mL的BPA溶液120 min,BPA去除率为96.4%。回收洗涤后第二次使用的催化剂的BPA去除率为80.5%,第三次使用的催化剂的BPA去除率为74.1%,催化剂的活性随重复使用次数的增加而缓慢降低,活性较稳定。     

电石法聚氯乙烯生产行业的汞污染防治

结合我国电石法聚氯乙烯生产行业的发展现状,提出了采用低汞触媒替代高汞触媒以降低汞消耗、开发高效除汞器以提高脱汞效率、深度解吸废盐酸以解决汞转移问题、深度处理含汞废水以实现综合利用、优化工艺控制以降低汞触媒消耗、改善防护措施以减轻汞扩散等汞污染防治工作的要点。     

用含锌废催化剂制备纳米氧化锌

以含锌废催化剂为原料,经酸浸、除杂、锌粉置换、合成等工艺制得碱式碳酸锌,再经过滤、洗涤、干燥、煅烧制备纳米氧化锌。考察了酸浸工艺硫酸溶液含量和液固比（硫酸与含锌废催化剂的质量比）对锌浸出率的影响,以及煅烧温度对纳米氧化锌质量的影响。实验结果表明：在硫酸质量分数为30%、液固比为5的最佳酸浸工艺条件下,锌浸出率为92%;在最佳煅烧温度为400 ℃的条件下,氧化锌质量分数大于95%,比表面积大于50 m²/g;纳米氧化锌颗粒大小均匀,平均粒径小于50 nm。     

含铜废催化剂中铜的回收

采用热解—氨浸工艺处理含铜废催化剂（w（Cu）为23.6%）,优化了工艺条件,并通过蒸氨还原法制备出Cu₂O产品。实验结果表明：热解工段中,控制管式热解炉的空气流量为3.0 m³/min,在升温速率20 ℃/min、热解终温600 ℃、终温保持时间90 min的优化条件下,含铜废催化剂中的有机物热解完全;氨浸工段中,以NH₄Cl-NH₃-H₂O溶液为氨浸液,控制氨浸温度为40 ℃,在烧成料研磨时间90 min（粒径29.43 μm）、氨浸液总氨浓度4 mol/L、氨浸时间80 min的优化条件下,铜浸出率达到98%;经蒸氨还原法制得的Cu₂O产品的质量符合HG/T 2961—2010《工业氧化亚铜》中的一等品标准,产率为24%。     

制备条件对Mn-Fe/TiO2催化剂低温脱硝性能的影响

通过浸渍法制备了一系列Mn-Fe/TiO2催化剂,并采用XRD技术对其进行了表征,考察了锰前体种类、负载量（活性组分质量占载体质量的百分比）、Fe含量（Fe物质的量占活性组分物质的量的百分比）、焙烧温度等因素对催化剂低温选择性催化还原NO性能的影响。实验结果表明：以乙酸锰为前体制备的催化剂的脱硝活性明显高于以硝酸锰为前体制备的催化剂;负载量的增加有利于脱硝活性的提高,而Fe的添加对提高催化剂的活性有重要作用,但Fe含量超过15%后,对催化剂脱硝性能的影响并不明显;焙烧温度超过650 ℃时会使活性组分的结晶度提高,导致脱硝活性的降低。在锰前体为乙酸锰、负载量为15%、Fe含量为15%、焙烧温度为500 ℃、焙烧时间为6 h、反应温度为200 ℃的条件下,Mn-Fe/TiO2催化剂的NO转化率约为95%。     

Magnetite/mesocellular carbon foam as a magnetically recoverable fenton catalyst for removal of phenol and arsenic

A magnetite-loaded mesocellular carbonaceous material, Fe₃O₄/MSU-F-C, exhibited superior activity as both a Fenton catalyst and an adsorbent for removal of phenol and arsenic, and strong magnetic property rendering it separable by simply applying magnetic field. In the presence of hydrogen peroxide, the catalytic process by Fe₃O₄/MSU-F-C completely oxidized phenol and As(III) under the conditions where commercial iron oxides showed negligible effects. Notably, the decomposition of H₂O₂ by Fe₃O₄/MSU-F-C was not faster than those by commercial iron oxides, indicating that hydroxyl radical produced via the catalytic process by Fe₃O₄/MSU-F-C was used more efficiently for the oxidation of target contaminants compared to the other iron oxides. The homogeneous Fenton reaction by the dissolved iron species eluted from Fe₃O₄/MSU-F-C was insignificant. At relatively high doses of Fe₃O₄/MSU-F-C, total concentration of arsenic decreased to a significant extent due to the adsorption of arsenic on the catalyst surface. The removal of arsenic by adsorption was found to proceed via preoxidation of As(III) into As(V) and the subsequent adsorption of As(V) onto the catalyst.     

Fe/Ce/沸石负载型类芬顿催化剂制备及其特性

采用柠檬酸盐溶胶-凝胶法制备了Fe/Ce/沸石负载型芬顿催化剂,通过透射电镜(TEM)和X射线衍射(XRD)对其进行表征,并将其作为非均相类芬顿催化剂处理孔雀石绿染料溶液。研究表明,通过掺杂Ce,可提高催化剂颗粒分散度和催化剂表面的氧气含量,进而提高催化活性。在催化剂投加量3.0 g/L,H2O2投加量67 mg/L,pH=8.0的条件下,反应30 min后,浓度为150 mg/L的孔雀石绿溶液脱色率可达97.3%。