三级串联人工快渗系统处理养殖废水

人工快速渗滤系统（constructed rapid infiltration,CRI）是在传统的污水快速渗透系统上发展起来的一种新的生物处理方法。采用猪粪浸泡污水模拟实际猪场处理系统的厌氧出水,研究三级串联人工快渗系统对其污染物的去除效果。试验结果表明,三级串联系统对废水COD、NH3N的去除率稳定在81%和94.5%,出水均满足了《畜禽养殖行业污染物排放标准》（GB18596-2001）的要求,同时三级串联系统还可以有效预防系统的堵塞。     

光合细菌强化二级流化床工艺处理焦化废水的研究

采用厌氧酸化加二级流化床组合工艺处理焦化废水。一级反应器内光合细菌与兼性厌氧菌处于共生状态,二级反应器内光合细菌与亚硝酸细菌处于共生状态。一级反应器内光合细菌有充分的小分子有机酸可降解并形成二次酸化,在二级反应器内完成进一步降解。结合反应条件：温度,pH,DO和基质浓度等,将二级反应器内硝化反应控制在亚硝化阶段,有效地保证了废水中碳源的利用。稳定运行了60 d,结果显示,出水COD和NH₃-N浓度分别为105～135 mg/L和14～20 mg/L,去除率分别稳定在90.3%～92.5%和92%～95%。TN去除率稳定在83%～86%。酚、氰化物和BOD5的去除率均在95%以上。     

污水污泥裂解及其性能的研究

以碘吸附值为裂解残渣吸附性能的指标,通过单因素实验和正交实验,确定了制备裂解残渣的最佳工艺条件,并对残渣的表面元素组成、孔结构组成、晶相组成和吸附性能等性质进行了表征。结果显示：以浓度均为5 mol/L的ZnCl₂和H₂SO₄作活化剂、复配比2∶1、活化温度600℃、活化时间1 h、固液比1∶2.5,制得的裂解残渣酸洗后碘值平均值可达892.8 mg/g;用制备的裂解残渣对苯酚废水进行处理,室温下振荡5 min,苯酚去除率即可达到87.9%,且符合Langmuir吸附等温线方程和Freundlich吸附等温线方程。     

催化湿式氧化法处理印染废水的研究

Cu-Fe和Cu-Ce/FSC是优化制备的均相和非均相催化剂,实验中将其应用于实际印染废水的CWAO法处理,考察催化剂的实用性能以及CWAO法对实际印染废水的处理效果。研究结果表明,CWAO法处理印染废水,出水COD、BOD₅均达到三级标准,色度和pH均达到一级标准,非均相的Cu溶出浓度达到三级标准;而处理出水BOD₅/COD由0.021（处理前）提高到0.423（均相）和0.307（非均相）,出水可生化性良好。     

赭石对模拟重金属废水的吸附效果研究

采用模拟重金属废水的正交试验设计,进行赭石对模拟重金属废水的吸附效果研究,探讨pH、赭石加入量和振荡时间等影响因素对吸附效果的影响。结果表明,在一定pH、赭石加入量和振荡时间条件下,赭石对6种重金属（Pb、Cd、Mn、Zn、Cr和Ni）均有较好吸附效果,对Pb、Cd、Mn、Zn和Cr的最大吸附率可达100%,对Ni的吸附率达8963%。处理后废水中重金属达到污水排放标准。各影响因素对Mn、Zn和Cr吸附效率的影响大小表现为：pH＞赭石加入量＞振荡时间,Ni和Cd表现为：赭石加入量＞pH＞振荡时间,Pb表现为：pH＞振荡时间＞赭石加入量。赭石对废水中重金属吸附的最佳条件为赭石加入量40 g/L,pH 10～10.5,振荡时间2 h。     

对苯二甲酸生产废水回用实验研究

采用高级氧化工艺对对苯二甲酸生产废水进行处理,系统考察了氧化剂投加量、废水pH等对处理效果的影响,得出了最佳工艺条件。经过处理的PTA废水,水质达到了车间用水的要求。本方法具有处理效果好、操作简单和环境友好等优点。     

高效菌藻塘系统对农村污水中磷的强化去除效果研究

研究了高效菌藻塘系统处理太湖地区农村生活污水除磷效果及其强化措施。高效菌藻塘和水生生物塘HRT分别为8 d和4 d,进水总磷浓度为1.7～17.1 mg/L,出水总磷浓度全年平均值为3.33 mg/L,高效菌藻塘系统的除磷能力欠佳。通过降低水生生物塘内水深、采用废弃石膏作为填料构建了新型复合水生生物塘,HRT=1.6 d条件下,复合水生生物塘出水总磷可保持在1 mg/L以下,可达到GB18918-2002一级B排放标准。     

聚硅酸锌铝的制备及其性能研究

以硅酸钠、硫酸锌、硫酸铝为原料,通过共聚法制备了无机高分子絮凝剂聚硅酸锌铝（PSZAS）,研究了Na₂SiO₃的摩尔浓度、活化时间、Al/Si、Zn/Si 配比及絮凝剂的投加量对絮凝效果的影响,用X-射线衍射（XRD）和电子扫描电镜（SEM）对该絮凝剂的结构及形貌进行了表征。结果表明：当硅酸钠的浓度为0.4 mol/L,硅酸活化时间为2 h,Si∶Al∶Zn=1∶1∶1.5,絮凝剂投加量为20 mL/L废水时,絮凝剂的电中和能力和吸附架桥能力最强,絮凝剂对含H-酸染料模拟废水的絮凝效果最好。     

Screening analysis of volatile organic contaminants in commercial inorganic coagulants used for drinking water treatment

A method for quality screening is suggested to detect volatile impurities in inorganic coagulants that are used for drinking water treatment. Static headspace gas chromatography with mass spectrometry detection (HS–GCMS) is sensitive and selective to detect volatiles in low concentrations. This study has discovered that volatile organic impurities are detectable in ferric and aluminium-based coagulants which are used for drinking water treatment. For ferric chloride, 2-propanol was detected at a level of 17–24 μg ml⁻¹, acetone at 0.7–1.7 μg ml⁻¹, 1,1,1-trichloroacetone at 0.02–0.04 μg ml⁻¹, trichloromethane at 0.01–0.02 μg ml⁻¹ and toluene at 0.01–0.12 μg ml⁻¹. For ferric chloride sulfate, acetone was detected at a level of 0.12 μg ml⁻¹, 1,1,1-trichloroacetone at 0.06–0.08 μg ml⁻¹, trichloromethane at 0.13–0.23 μg ml⁻¹, bromodichloromethane at 0.04–0.06 μg ml⁻¹ and dibromochloromethane at 0.04–0.05 μg ml⁻¹. For aluminium hydroxide chloride, only trichloromethane was detectable, but below the method detection limits (MDL). Although the concentrations of these impurities in commercial coagulants are low, this observation is important and should have impact on water industries for them to pay attention to the chemicals they are using for drinking water production.     

Adsorption of phenol and its derivatives from water using synthetic resins and low-cost natural adsorbents: a review

In this article, the technical feasibility of the use of activated carbon, synthetic resins, and various low-cost natural adsorbents for the removal of phenol and its derivatives from contaminated water has been reviewed. Instead of using commercial activated carbon and synthetic resins, researchers have worked on inexpensive materials such as coal fly ash, sludge, biomass, zeolites, and other adsorbents, which have high adsorption capacity and are locally available. The comparison of their removal performance with that of activated carbon and synthetic resins is presented in this study. From our survey of about 100 papers, low-cost adsorbents have demonstrated outstanding removal capabilities for phenol and its derivatives compared to activated carbons. Adsorbents that stand out for high adsorption capacities are coal-reject, residual coal treated with H3PO4, dried activated sludge, red mud, and cetyltrimethylammonium bromide-modified montmorillonite. Of these synthetic resins, HiSiv 1000 and IRA-420 display high adsorption capacity of phenol and XAD-4 has good adsorption capability for 2-nitrophenol. These polymeric adsorbents are suitable for industrial effluents containing phenol and its derivatives as mentioned previously. It should be noted that the adsorption capacities of the adsorbents presented here vary significantly depending on the characteristics of the individual adsorbent, the extent of chemical modifications, and the concentrations of solutes.