热活化对海泡石处理模拟含油废水性能的影响

以海泡石粉末为原料,对其进行热活化处理,考察了焙烧温度、焙烧时间、吸附剂用量、废水初始pH、温度等对模拟含油废水COD去除效果的影响。实验结果表明:经400℃热活化后,海泡石的比表面积由247.797 m2/g增加至305.849 m2/g,热活化海泡石对模拟含油废水中COD的吸附等温式符合Freundlich方程。     

Activation of sulfite by metal-organic framework-derived cobalt nanoparticles for organic pollutants removal

Sulfite (SO₃²⁻) activation is one of the most potential sulfate-radical-based advanced oxidation processes, and the catalysts with high efficiency and low-cost are greatly desired. In this study, the cobalt nanoparticles embedded in nitrogen-doped graphite layers (Co@NC), were used to activate SO₃²⁻ for removal of Methyl Orange in aqueous solution. The Co@NC catalysts were synthesized via pyrolysis of Co²⁺-based metal-organic framework (Co-MOF), where CoO was firstly formed at 400℃ and then partially reduced to Co nanoparticles embedded in carbon layers at 800℃. The Co@NC catalysts were more active than other cobalt-based catalysts such as Co²⁺, Co₃O₄ and CoFe₂O₄, due to the synergistic effect of metallic Co and Co_xO_y. A series of chain reaction between Co species and dissolved oxygen was established, with the production and transformation of SO₃^•−, SO₅²⁻, and subsequent active radicals SO₄^•− and HO•. In addition, HCO₃⁻ was found to play a key role in the reaction by complexing with Co species on the surface of the catalysts. The results provide a new promising strategy by using the Co@NC catalyst for SO₃²⁻ oxidation to promote organic pollutants degradation.     

粉煤灰的活化性能研究

研究了粉煤灰的活化方法,确定了最适宜的活化剂HR和相应的活化条件。利用XPS．IR．TEM．TGA和DTA等方法研究了活化粉煤灰的表面成分、基团和形貌。考察了活化粉煤灰的疏水性和在有机介质中的分散性及亲和性。证明活化剂分子是以化学键牢固地结合在粉煤灰表面上而使其显著改性。     

稻壳吸附剂净化水中有机污染物的研究

以酸处理稻壳为原料，研究了稻壳吸附剂的活化工艺，所制备的吸附剂对水中芳香化合物和杂环染料均有较大的吸附能力。通过试验得出了吸附剂净化水中芳香化合物及染料的最佳条件     

流化床锅炉飞灰活性激发与建材利用的试验研究

流化床锅炉飞灰活性较差,常规的粉煤灰活性激发方法对该飞灰效果不佳.本研究采用了加入适当激发剂的方法激发其活性,结果表明,加入激发剂后水泥胶砂的早期抗折、抗压强度均有100%的增长,后期抗折强度提高约100%、抗压强度提高60%以上,凝结时间和安定性均符合要求.水泥中飞灰掺量达40%时,其胶砂各龄期强度均达到甚至超过了42.5R水泥的强度;飞灰掺量65%～75%时,胶砂强度显示仍可生产一些低强度要求的建材产品,如砌筑水泥、建筑砂浆等.采用XRD、SEM等微观测试手段对飞灰活性激发机理进行了探讨.     

木镁基碳质吸附剂的制备及其性能

用木镁聚合物（PML）制备碳质吸附剂,探讨了影响产物吸附性能的主要制备因素。结果表明,当活化温度为400℃,磷料比为2：1和活化时间为2.5 h时,木镁基碳质吸附剂（MLCA）的吸附性能较好,其亚甲基蓝吸附值为142.5 mg/g,碘吸附值为946.43 mg/g。红外光谱分析表明,经过高温处理后,产物保持了PML的基本结构特征,而其比表面积由0.07 m2/g增大至642.38 m2/g。MLCA对染料亚甲基蓝的吸附过程符合Langmuir吸附等温式。     

水蒸气改善钙基CO2吸收剂循环活性的研究

对钙基CO2吸收剂的循环活性改善进行了研究,分析了水蒸气处理对吸收剂的最大转化率、比表面积及孔分布等微观结构变化的影响。结果表明,经水蒸气处理后,钙基CO2吸收剂的循环活性得到了改善,最大转化率比未经水蒸气处理可提高约50百分点;水蒸气处理可大大提高钙基CO2吸收剂的比表面积,并有效改善其孔径分布状态,可使其稳定保持较高的转化率;含碳能源直接制氢过程可在不需要任何添加剂或辅助手段的条件下,有效保持钙基CO2吸收剂的循环活性。     

等离子球磨机的研制及其振动平台试验

目的实现球磨室在常压下的大面积介质阻挡放电等离子体,开发出商用等离子球磨机。方法通过在不同弹簧和平台质量条件下,利用振动传感器测试平台的振幅(峰峰值)和加速度(有效值)数值,对比确定最优配置和机械振动参数。结果当振动平台振幅接近球磨室内径时,获得高振幅和高加速度的磨球,显著缩短了气体放电间距,实现了球磨室在常压下的大面积介质阻挡放电等离子体。所设计的单筒等离子振动球磨机,其振动平台可选用φ7 mm、φ8 mm两组弹簧,根据平台质量的不同,选择不同类型的激振块组合,可以在30 Hz转速以上实现平台振幅峰峰值达到或者接近球磨罐内径值,同时拥有10g以上的加速度有效值。结论本试验综合机械振动学、高压绝缘放电和材料加工技术,所研制的等离子体球磨机实现了机械能和等离子体能在球磨过程中的协同作用,显著提高了粉末活性,降低了化合物合成反应激活能,从而显著提高了所制备材料的性能。     

Peroxymonosulfate enhanced photoelectrocatalytic oxidation of organic contaminants and simultaneously cathodic recycling of silver

Degradation of organic contaminants with simultaneous recycling of Ag⁺ from silver-containing organic wastewater such as photographic effluents is desired. Although photoelectrocatalysis (PEC) technology is a good candidate for this type of wastewater, its reaction kinetics still needs to be improved. Herein, peroxymonosulfate (PMS) was employed to enhance the PEC kinetics for oxidation of phenol (PhOH) at the anode and reduction of Ag⁺ at the cathode. The degradation efficiency of phenol (PhOH, 0.1 mmol/L) was increased from 42.8% to 96.9% by adding 5 mmol/L PMS at a potential of 0.25 V. Meanwhile, the Ag (by wt%) deposited on the cathode was 28.1% (Ag₂O) in PEC process, while that of Ag (by wt%) was 69.7% (Ag⁰) by adding PMS. According to the electrochemistry analysis, PMS, as photoelectrons acceptor, enhances the separation efficiency of charges and the direct h⁺ oxidation of PhOH at the photoanode. Meantime, the increasing cathode potential avoided H₂ evolution and strongly alkaline at the surface of cathode, thus enabling the deposition of Ag⁺ in the form of metallic silver with the help of PMS. In addition, PMS combined with PEC process was effective in treating photographic effluents.     

Preparation and characterization of activated carbon from a new raw lignocellulosic material: Flamboyant (Delonix regia) pods

Activated carbons were prepared from flamboyant pods by NaOH activation at three different NaOH:char ratios: 1:1 (AC-1), 2:1 (AC-2), and 3:1 (AC-3). The properties of these carbons, including BET surface area, pore volume, pore size distribution, and pore diameter, were characterized from N₂ adsorption isotherms. The activated carbons obtained were essentially microporous and had BET surface area ranging from 303 to 2463 m² g⁻¹.¹³C (CP/MAS and MAS) solid-state NMR shows that the lignocellulosic structures were completely transformed into a polycyclic material after activation process, thermogravimetry shows a high thermal resistance, Boehm titration and Fourier-transform infrared spectroscopy allowed characterizing the presence of functional groups on the surface of activated carbons. Scanning electron microscopy images showed a high pore development. The experimental results indicated the potential use of flamboyant pods as a precursor material in the preparation of activated carbon.