铁锰复合氧化物/壳聚糖珠:一种环境友好型除磷吸附剂

采用两步法制备了一种环境友好型除磷基吸附剂——铁锰复合氧化物/壳聚糖珠(FMCB),对其进行了表征,并对其磷吸附行为进行了系统研究.表征结果表明,该吸附剂为多孔纤维结构,比表面积为248 m~2·g~(-1),孔容为0.37 m~3·g~(-1).吸附实验结果表明,FMCB对磷的吸附容量远高于纯的壳聚糖颗粒,且Langmuir模型能更好地拟合FMCB对磷的吸附,最大吸附量为13.3 mg·g~(-1)(pH 7.0);准二级动力学模型能更好地拟合FMCB对磷吸附的动力学实验数据;溶液pH对磷的吸附影响较大,随着pH的增大,磷的吸附量逐渐降低;共存的Ca~(2+)和Mg~(2+)对磷吸附略有促进,而共存阴离子对磷吸附具有抑制作用,影响大小顺序为:SiO_3~(2-)CO_3~(2-)SO_4~(2-)≥Cl~-.吸附磷后的FMCB可用NaOH溶液进行脱附再生,并可重复使用.在进水磷初始浓度为3 mg·L~(-1)条件下,吸附达到穿透时(出水磷浓度达0.5 mg·L~(-1)),可处理约800个柱体积的模拟含磷废水.     

灼烧净水污泥对外源磷的吸附和固定作用

研究了不同投加方式下(混匀和覆盖)灼烧净水污泥对外源磷的累积吸附效果,以及吸附外源磷后底泥等温吸附效果和在厌氧条件下内源磷释放情况.结果表明,混匀和覆盖条件下,底泥对上覆水中磷的累积吸附量分别为11.496 mg和11.042 mg,明显高于对照实验(7.219 mg).通过对吸附外源磷后的底泥进行等温吸附实验,发现混匀条件和覆盖条件下磷最大吸附量(Smax)均有所增加,并且前者(7.795 mg·g~(-1))要高于后者(6.807 mg·g~(-1)),但磷平衡浓度(EPC0)前者(0.83mg·L~(-1))却明显大于后者(0.64 mg·L~(-1)),表明混匀条件下内源磷更容易释放.在厌氧环境下,混匀方式内源磷释放量仅为0.93 mg,不仅低于覆盖(1.49 mg),也明显低于对照实验(7.76 mg).覆盖条件下比释放速率的平均值(0.006 14)大于混匀(0.003 96),并均低于对照实验.这说明混匀对内源磷的持留能力更强.暗示了单纯用EPC0值来评价底泥对磷的固定能力是不妥的.     

土壤重金属钝化修复剂生物炭对镉的吸附特性研究

目前以生物炭为代表的生物质对重金属的吸附表现出良好的应用前景.为确定生物炭对溶液中镉的吸附性能,选用由棉花秸秆制备的生物炭,研究吸附等温线、吸附动力学以及温度、pH和离子强度等对生物炭吸附Cd2+的影响.研究表明,生物炭对Cd2+的吸附可以用Freundlich等温线较好地拟合,在不同温度下其饱和吸附量分别为9.738 mg.g-1(288.15 K)、10.14 mg.g-1(298.15 K)、10.40 mg.g-1(308.15 K)和10.71 mg.g-1(318.15 K),热力学参数表明生物炭吸附Cd2+的过程是自发的吸热过程;吸附动力学过程符合二级动力学模型,在40 min即可达到平衡;pH对生物炭吸附Cd2+的影响较大,在pH2～8范围时,生物炭对Cd2+的吸附量随pH的增加先上升后下降;生物炭对Cd2+的吸附量随着溶液离子强度的增大呈降低趋势.该项研究可为生物炭在土壤重金属污染修复中的应用提供一定的理论基础.     

La3+掺杂对吸附相反应制备TiO2复合催化剂的结晶过程及弱紫外光下活性的影响

利用吸附相反应技术制备弱紫外光响应的高效催化剂,并通过XRD、XPS以及HRTEM探索了不同焙烧温度下La3+掺杂量对TiO2结晶过程的影响.结合弱紫外光下甲基橙的降解反应,深入研究催化剂结晶过程的变化对弱紫外光下催化剂活性的影响.结果表明,La3+掺杂会抑制TiO2的结晶过程.当焙烧温度或者掺杂量较低时,La3+不能进入TiO2的晶格结构但会轻微地抑制TiO2的结晶过程;未进入晶格结构的La3+存在会引入光生载流子的浅能级捕获中心,在弱光体系中极大提升了催化剂的活性.当La3+的掺杂量为0.05%(原子分数)时,经过900℃焙烧后催化剂降解能力最高,其活性超过商用P25的2倍多.在较高La3+掺杂量(超过0.20%)时,900℃焙烧后一定量La3+进入TiO2的晶格结构而大大抑制了TiO2结晶;这种强烈的抑制作用使得催化剂中存在大量无定形结构TiO2,无定形TiO2甚至多于700℃焙烧后的催化剂,反而大大抑制了弱光体系中催化剂活性.     

固载化瓜环的制备及其对磺胺间甲氧嘧啶的吸附性能研究

在微波无极灯下将烯氧基瓜环固载到巯基硅胶(MSG)上,制得固载化瓜环(ACB[6]-SG).通过红外光谱表征固载产物,并研究固载化瓜环对磺胺间甲氧嘧啶(SMM)的吸附性能.结果表明,SMM在固载化瓜环上的吸附基本在2 min内即可达到平衡;Henry方程和Freundlich方程均能较好地拟合SMM在固载化瓜环和巯基硅胶上的等温吸附曲线,但是SMM在固载化瓜环上的吸附主要是在瓜环中的分配,而SMM在巯基硅胶上的吸附则主要是多分子层的表面吸附作用;SMM在固载化瓜环上的平衡吸附量远大于在巯基硅胶上的平衡吸附量;SMM在两者上的吸附过程是一个放热过程,温度越低吸附效果越好.     

汽油在西北黄土上吸附特性的研究

通过动力学和热力学吸附实验,研究了汽油在西北地区黄土上的吸附行为,同时研究了提取的天然腐植酸对汽油在黄土上吸附行为的影响.结果表明,汽油在黄土上的吸附在6h内达到平衡.无论是否加入腐植酸,汽油在黄土上的吸附动力学过程均符合Elovich方程,其热力学吸附符合Freundlich方程.腐植酸的存在使汽油在黄土上的吸附能力减小.反应温度从25℃升高到45 C,汽油在土壤上的饱和吸附量从6.300mg·g-1减小到1.365 mg·g-1,表明汽油在黄土上的吸附属于放热反应.溶液pH和土壤粒径的增大,均不利于汽油在黄土上的吸附,溶液pH和土壤粒径越大,其在黄土上的吸附量越小.另外,在室温下对吸附了汽油的土壤样品和纯汽油挥发行为的研究表明,吸附了汽油的土壤样品的汽油挥发比纯汽油慢,其挥发率与时间成对数关系.     

Adsorption of lead on multi-walled carbon nanotubes with different outer diameters and oxygen contents: Kinetics, isotherms and thermodynamics

The effects of different outer diameters and surface oxygen contents on the adsorption of heavy metals onto six types of multi-walled carbon nanotubes (MWCNTs) were investigated in an aqueous solution and lead was chosen as a model metal ion. The results indicated that the percentage removal and adsorption capacity of lead remarkably increased with decreasing outer diameter due to larger specific surface area (SSA). The SSA-normalized maximum adsorption capacity (qm /SSA) and SSA-normalized adsorption coefficient (Kd /SSA) were strongly positively correlated with surface oxygen content, implying that lead adsorption onto MWCNTs significantly increases with the rise of oxygen content and decreases with decreasing SSA. The calculated thermodynamic parameters indicated that adsorption of lead on MWCNTs was endothermic and spontaneous. When the oxygen content of MWCNTs increased from 2.0% to 5.9%, the standard free energy (△ G0 ) became more negative, which implied that the oxygenated functional groups increased the adsorption affinity of MWCNTs for lead. Through calculation of enthalpy (△ H0 ), G0 and free energy of adsorption (Ea ), lead adsorption onto MWCNTs was recognized as a chemisorption process. The chemical interaction between lead and the phenolic groups of MWCNTs could be one of the main adsorption mechanisms due to highly positive correlations between the phenolic groups and K d /SSA or q m /SSA.     

Ethyl thiosemicarbazide intercalated organophilic calcined hydrotalcite as a potential sorbent for the removal of uranium(VI) and thorium(IV) ions from aqueous solutions

This work was conducted to determine the practicability of using a new adsorbent 4-ethyl thiosemicarbazide intercalated,organophilic calcined hydrotalcite(ETSC-OHTC) for the removal of uranium(U(VI)),and thorium(Th(IV)) from water and wastewater.The FTIR analysis helped in realizing the involvement of nitrogen and sulphur atoms of ETSC in binding the metal ions through complex formation.Parameters like adsorbent dosage,solution pH,initial metal ions concentration,contact time and ionic strength,that influence adsorption phenomenon,were studied.The optimum pH for maximum adsorption of U(VI) and Th(IV) was found to be in the range 4.0-6.0.The contact time required for reaching equilibrium was 4 hr.The pseudo second-order kinetic model was the best fit to represent the kinetic data.Analysis of the equilibrium adsorption data using Langmuir,Freundlich and Sips models showed that the Freundlich model was well suited to describe the metal ions adsorption.The K F values were 25.43 and 29.11mg/g for U(VI) and Th(IV),respectively,at 30°C.The adsorbent can be regenerated effectively from U(VI) and Th(IV) loaded ones using 0.01mol/L HCl.The new adsorbent was quite stable for many cycles,without much reduction in its adsorption capacity towards the metals.     

Pb(II) removal from water using Fe-coated bamboo charcoal with the assistance of microwaves

Bamboo charcoal(BC) was used as starting material to prepare iron-modified bamboo charcoal(Fe-MBC) by its impregnation in FeCl 3 and HNO 3 solutions simultaneously,followed by microwave heating.The material can be used as an adsorbent for Pb(Ⅱ) contaminants removal in water.The composites were prepared with Fe molar concentration of 0.5,1.0 and 2.0 mol/L and characterized by means of N 2 adsorption-desorption isotherms,X-ray diffraction spectroscopy(XRD),scanning electron microscopy coupled with energy dispersive X-ray spectrometry(SEM-EDS),Fourier transform infrared(FT-IR) and point of zero charge(pH pzc) measurements.Nitrogen adsorption analyses showed that the BET specific surface area and total pore volume increased with iron impregnation.The adsorbent with Fe molar concentration of 2 mol/L(2Fe-MBC) exhibited the highest surface area and produced the best pore structure.The Pb(Ⅱ) adsorption process of 2Fe-MBC and BC were evaluated in batch experiments and 2Fe-MBC showed an excellent adsorption capability for removal Pb(Ⅱ).The adsorption of Pb(Ⅱ) strongly depended on solution pH,with maximum values at pH 5.0.The ionic strength had a significant effect on the adsorption at pH < 6.0.The adsorption isotherms followed the Langmuir isotherm model well,and the maximum adsorption capacity for Pb(Ⅱ) was 200.38 mg/g for 2Fe-MBC.The adsorption processes were well fitted by a pseudo second-order kinetic model.Thermodynamic parameters showed that the adsorption of Pb(Ⅱ) onto Fe-MBC was feasible,spontaneous,and exothermic under the studied conditions,and the ion exchange mechanism played an significant role.These results have important implications for the design of low-cost and effective adsorbents in the removal of Pb(Ⅱ) from wastewater.     

Adsorption of 2-mercaptobenzothiazole from aqueous solution by organo-bentonite

The adsorption behavior of 2-mercaptobenzothiazole onto organo-bentonite was investigated.Natural bentonite from Gaozhou in Guangdong Province,China was collected.Organo-bentonite was prepared by intercalation of cetyltrimethyl ammonium bromide into the natural bentonite.The physicochemical properties of the prepared organo-bentonite were characterized by X-ray diffraction,N2 adsorption-desorption isotherm and Fourier transform infrared spectroscopy.The results showed that montmorillonite is the main component of the natural bentonite.The basal spacing of the natural bentonite is 1.47 nm,which increased to 1.98 nm on intercalation with cetyltrimethyl ammonium bromide.Moreover,both the surface area and pore volume increased with intercalation.Clear CH2 stretching(3000-2800 cm-1) and scissoring(1480-1450 cm-1) modes of the intercalated surfactants were observed for organobentonite.Compared with the pseudo first-order kinetic model,the pseudo second-order kinetic model is more suitable to describe the adsorption kinetics of 2-mercaptobenzothiazole onto organo-bentonite.The adsorption capacity of 2-mercaptobenzothiazole onto organo-bentonite increased with increasing initial concentration of 2-mercaptobenzothiazole,but decreased with increasing adsorbent dosage.The adsorption isotherm of 2-mercaptobenzothiazole onto organo-bentonite fits well with the Langmuir model.The maximum adsorption capacity of organo-bentonite for 2-mercaptobenzothiazole was 33.61 mg/g,indicating that organo-bentonite is a promising adsorbent for 2-mercaptobenzothiazole.