Synthesis of poly(hydroxyalkanoate) from hydrolyzed linseed oil

Pseudomonas putida was grown on a mixture of long-chain fatty acids obtained by hydrolysis of linseed oil. A poly(3-hydroxyalkanoate) containing 51.2% of unsaturated monomers was obtained. A considerable percentage (13.6%) was constituted by C₁₄ and C₁₆ monomers containing three double-bonds in the side chains. The polymer showed a high tendency to crosslink when it was kept in presence of air. In the crosslinked polymer no polyunsaturated monomers could be detected.     

仪化热电厂提高循环水浓缩倍率的措施

针对仪化热电厂将循环水用作冲灰水，导致浓缩倍率只有1.6，以及凝汽器铜管腐蚀结垢严重等问题，提出了隔断循环水与冲灰水的直接联系，实现闲路循环，对凝汽器铜管进行酸洗，并对循环水实施加缓蚀阻垢荆、杀菌剂和旁流过滤等办法，全部实施后产生了很好的效益，值得借鉴。     

O2-Fenton试剂处理对氨基苯磺酸废水的探讨

利用由O2和Fenton试剂组成的类Fenton系统处理对氨基苯磺酸废水,取得了很好的降解效果.当FeSO4(10g/L)投加量为1.2mL、H2O2(3%)投加量为3mL时,COD去除率可达到70%.     

Mechanical and Barrier Properties of Biodegradable Films Made from Chitosan and Poly (Lactic Acid) Blends

Biodegradable film blends of chitosan with poly(lactic acid) (PLA) were prepared by solution mixing and film casting. The main goal of these blends is to improve the water vapor barrier of chitosan by blending it with a hydrophobic biodegradable polymer from renewable resources. Mechanical properties of obtained films were assessed by tensile test. Thermal properties, water barrier properties, and water sensitivity were studied by differential scanning calorimeter analysis, water vapor permeability measurements, and surface-angle contact tests, respectively. The incorporation of PLA to chitosan improved the water barrier properties and decreased the water sensitivity of chitosan film. However, the tensile strength and elastic modulus of chitosan decreased with the addition of PLA. Mechanical and thermal properties revealed that chitosan and PLA blends are incompatible, consistent with the results of Fourier transform infrared (FTIR) analysis that showed the absence of specific interaction between chitosan and PLA.     

超声-双氧水和亚铁离子体系处理含酚废水研究

在实验装置上对超声-双氧水和亚铁离子体系联合处理含酚废水进行了实验研究。主要考察了废水初始pH值、初始双氧水浓度、超声功率、反应时间等因素对酚去除率的影响。实验结果表明：超声辐射可以在双氧水和亚铁离子体系氧化过程中起加速反应的作用，而且随着超声功率的增大，加速反应的能力增强；实验条件下废水初始pH值为4～6．8，初始双氧水浓度为140mg／L时酚去除效果最佳；超声-双氧水和亚铁离子体系处理含酚废水过程中苯酚的降解规律符合表现一级反应。     

尿中氚水和总氚的分析测定

用蒸馏-液闪法和氧化蒸馏-液闪法分别测量了氚污染人员尿中的氚水浓度和总氚(氚水和有机氚)浓度。根据72个高于本底水平的尿中氚水和总氚浓度分析比较，认为在氚内污染工作人员的尿中，有机氚与氚水的浓度比值为(5.4 3.7)％。     

金沙江对硫酸的缓冲性能分析

本文分析了金沙江对硫酸的缓冲特征，建立了江水的缓冲曲线方程，并且验证了此方程的有效性，证明用此方程预测硫酸进入金沙江后江水pH值的变化情况，其预测准确度在0.2个pH单位内。     

Environmental assessment of supercritical water oxidation of sewage sludge

Environmental aspects of using supercritical water oxidation (SCWO) to treat sewage sludge were studied using a life cycle assessment (LCA) methodology. The system studied is the first commercial scale SCWO plant for sewage sludge in the world, treating sludge from the municipal wastewater treatment facility in Harlingen, TX, USA. The environmental impacts were evaluated using three specific environmental attributes: global warming potential (GWP), photo-oxidant creation potential (POCP) and resource depletion; as well as two single point indicators: EPS2000 and EcoIndicator99. The LCA results show that for the described process, gas-fired preheating of the sludge is the major contributor to environmental impacts, and emissions from generating electricity for pumping and for oxygen production are also important. Overall, SCWO processing of undigested sewage sludge is an environmentally attractive technology, particularly when heat is recovered from the process. Energy-conserving measures and recovery of excess oxygen from the SCWO process should be considered for improving the sustainability potential.     

亚甲蓝湿式氧化影响因素研究

以湿式氧化技术对亚甲蓝水溶液进行处理,用水样COD去除率评价处理效果.考察了反应时间、温度、氧分压、搅拌速度、进水pH值以及进水浓度对处理效果的影响,并进行机理分析.实验确定的最佳操作工艺条件为:反应温度210℃、氧分压2.0 MPa、搅拌速度880 r/min、进水pH=11.30.在此条件下,COD为2 000mg/L的亚甲蓝水溶液,反应90min时COD去除率达93.2%.     

水解-接触氧化工艺处理针织染整废水

介绍了采用水解-接触氧化工艺处理针织染整废水,工程运行结果表明：CODcr和色度的去除率分别达到91.3%、88%,最终排放污水达到国家污水Ⅰ级标准.该工艺具有处理效果好、经济、运行稳定等特点,在染整废水处理中具有实用性.