Waste management of electric and electronic equipment: comparative analysis of end-of-life strategies

This article analyzes diverse aspects of the waste management of electronic and electric equipment. The scope of the study focuses on end-of-life strategies currently implemented in industrialized economies such as Japan, the United States, and the European Union. The objective is a comparative analysis of such strategies in order to identify logistic issues that may contribute to the further improvement of waste management policies. The results indicate that although all strategies follow the extended producer responsibility principle, in practice several logistic differences arise due to particular interpretations of the concept. In general, it was observed that a direct comparison is rather difficult since the strategies consider different legal frameworks, they cover different types and numbers of products, and the resultant mass flows and related operational costs are highly context-dependent variables. Therefore, it is not possible to indicate which strategy presents the highest overall efficiency. The study concludes that a little contribution is feasible if the advantages and weaknesses of the models depicted and discussed here are considered in further regulatory decisions.Extended version of the poster presentation A comparative analysis of end-of-life strategies for home appliances in Japan, America, and the European Union, accepted at the 31st Annual Meeting of Environmental Systems Research, Japan Society of Civil Engineers (JSCE), October 24–25, 2003, Kitakyushu, Japan     

Effect of Decalin Solvent on the Thermal Degradation of HDPE

The thermal cracking of HDPE in presence of different amounts of decalin was studied and compared with the reaction carried out in the absence of solvent. The decalin favours the mass and heat transfer during the reaction. In addition, it modifies the thermal degradation mechanism, which facilitates the formation of specific products. The use of decalin substantially increases the C₅–C₃₂ yield in comparison with the solventless reaction. In all cases, linear hydrocarbons such as n-paraffins, α-olefins and α,ω-dienes were detected. Increasing the decalin/plastic ratio led to enhanced α-olefin and n-paraffins yields, but the increase was more significant in the case of α-olefins, which are valuable compounds useful as raw chemicals. A reaction mechanism was proposed to explain the results obtained in presence of decalin. In these reactions, intramolecular radical transfer, secondary radical β-scission and hydrogen transfer from both decalin to intermediate radicals and from the polymer chain to regenerate the decalin play a significant role in determining the plastic conversion and the relative amounts of each product.     

Evaluation of the effect of automotive bumper recycling by life-cycle inventory analysis

This paper describes a case study of the application of life-cycle inventory analysis to automotive bumper recycling. Two scenarios of bumper recycling are compared. One is “bumper-to-bumper recycling,” in which we recycle bumpers into more bumpers. The other is “cascade recycling,” in which bumpers are recycled into different parts of a car with a lower function. Inventory analysis is applied to both these recycling scenarios by analyzing the stages of acquiring natural resources, manufacturing materials, and parts, disposal, and recycling. We chose air emission, solid waste, and fossil fuel resources as items of the inventory analysis. We quantified the effect of reductions in the environmental load by recycling bumpers, and found that reductions in the environmental load were larger with cascade recycling than with bumper-to-bumper recycling based on current conditions. Received: February 2, 2000 / Accepted: April 21, 2000     

Comparison of the weight-loss degradability of various biodegradable plastics under laboratory composting conditions

Eight kinds of biodegradable plastics were compared for their degradability in controlled laboratory composting conditions. A thin film of each plastic was mixed into the composting material, and weight-loss degradability was calculated from the weight changes of the film during composting. It was found that weight-loss degradability strongly depended on the specific kind of biodegradable plastic; two were very high, four moderate, and the remaining two very slight. The most easily degradable plastic degraded by as much as 81.4% over 8 days of composting. By comparing the weight-loss degradability with ultimate degradability, which is defined as a molar ratio of carbon loss as CO₂ to the carbon contained in the biodegradable plastic, the order of the ease of degradation of the biodegradable plastics differed. Received: February 7, 2000 / Accepted April 14, 2000     

Analysis of the role of waste minimisation clubs in reducing industrial water demand in the UK

As a result of the UK Government's waste policy, which increasingly encourages sustainable development, and the realisation that water in the UK cannot be treated as an unlimited resource, there is growing interest in reducing the demand for water by industry. A series of industrial waste minimisation clubs have been set up within the country. This paper identifies the effectiveness of these clubs in reducing the demand for water. An overview of some of the clubs show how there is a major discrepancy between potential and implemented water savings, whilst a more detailed analysis of three specific examples show how water demand and cost to the company can be reduced, with the project paying for itself within around 1 year. It appears that companies are able to reduce water consumption by approximately 30%. If this level of saving was taken up by the entire industrial sector in England and Wales, water consumption could be reduced by approximately 1500 Ml/day. This reduction would be more significant in regions of lower rainfall, for example East Anglia and Southeast England.     

Recyling of plastic wastes via pyrolysis

Pyrolysis for the simultaneous generation of oils and gases can be convenient to obtain hydrocarbons and even to recover crude petrochemicals or to generate energy from waste plastics. A Gray–King apparatus has been used to pyrolyze waste polyethylene (PE), polystyrene (PS), both separately and with different compositions. Thermogravimetric analysis of waste plastics indicated the critical temperatures, which should be effective for pyrolysis. The chosen heating rate was low in order to achieve higher liquid yields. The results showed that waste PS yielded higher liquid, and waste PE yielded higher gaseous products. The dominant liquid product of PS waste was styrene whereas for waste PE, prophenylbenzene was the dominant pyrolysis product.     

Converting waste polystyrene into a polymer flocculant for wastewater treatment

We have succeeded in converting waste polystyrene from electrical appliances into a polymer flocculant for treating some kinds of wastewater after chemical modification. Waste polystyrene, such as polystyrene foam and additive-containing TV cabinets, was converted into a water-soluble polymer, polystyrene sulfate (PSS), and PSS of various degrees of aqueous viscosity was obtained by introducing sulfone bridges during sulfonation. We examined the relationship between the degree of flocculation of wastewater and the aqueous viscosity of the PSS, and found that PSS with medium viscosity is most suitable for flocculating inorganic wastewater from a factory, and PSS with high viscosity is most suitable for dewatering organic domestic wastewater. We report how PSS containing sulfone bridges works as a polymer flocculant for treating wastewater. Received: July 19, 2000 / Accepted: September 21, 2000     

浅论城市生活垃圾的资源化系统

现在社会产生越来越多,组份越来越复杂的生活垃圾,已成为严重的环境和社会问题。本文通过对垃圾成份和数量的分析,结果国内外垃圾处理的发展现状,针对四川省省情,提出了加强垃圾分类收集、分选回收,以堆肥、焚烧、再生等手段实现垃圾的资源化系统。并且,对目前的垃圾处理所涉及到的政府职能和社会意识等软环境作了简单描述。     

铜铬电镀废液中铬回收方法

用亚硫酸钠将电镀废液中的六价铬还原为三价铬,用硫化钠除去铜,用氢氧化钠沉淀三价铬后,用一定量的硫酸溶解氢氧化铬后得到碱式硫酸铬加以回收利用。     

An advanced study on the hydrometallurgical processing of waste computer printed circuit boards to extract their valuable content of metals

This study refers to two chemical leaching systems for the base and precious metals extraction from waste printed circuit boards (WPCBs); sulfuric acid with hydrogen peroxide have been used for the first group of metals, meantime thiourea with the ferric ion in sulfuric acid medium were employed for the second one. The cementation process with zinc, copper and iron metal powders was attempted for solutions purification. The effects of hydrogen peroxide volume in rapport with sulfuric acid concentration and temperature were evaluated for oxidative leaching process. 2 M H₂SO₄ (98% w/v), 5% H₂O_2, 25 °C, 1/10 S/L ratio and 200 rpm were founded as optimal conditions for Cu extraction. Thiourea acid leaching process, performed on the solid filtrate obtained after three oxidative leaching steps, was carried out with 20 g/L of CS(NH₂)₂, 6 g/L of Fe³⁺, 0.5 M H₂SO₄, The cross-leaching method was applied by reusing of thiourea liquid suspension and immersing 5 g/L of this reagent for each other experiment material of leaching. This procedure has lead to the doubling and, respectively, tripling, of gold and silver concentrations into solution. These results reveal a very efficient, promising and environmental friendly method for WPCBs processing.